Bug#378713: xserver-xorg-video-ati: DRI disabled because it cannot see AGP kernel interface
On Tue, 2006-07-18 at 17:44 +0200, Michel Dänzer wrote:
> Note that I don't think lsmod lists the modules in the order they were
> loaded. Also, the above message was written back when both radeon and
> agpgart were still monolithic modules. Now that they have both been
> split into core and backend modules, the safest bet is to make sure that
> both the agpgart and intel_agp modules are loaded before both the drm
> and radeon modules. Running
>
> modprobe -r radeon; modprobe radeon
>
> should achive this in your case. If restarting the X server after doing
> this still doesn't enable the DRI, please provide the kernel output.
I did what you suggested (several times) and DRI is still disabled.
Here are the kernel messages. As you can read, I use a standard Debian
kernel. In the error messages at the end, the PID are those of the X
servers.
--
Laurent Bonnaud.
http://www.lis.inpg.fr/pages_perso/bonnaud/
Linux version 2.6.17-1-686 (Debian 2.6.17-4) (waldi@debian.org) (gcc version 4.1.2 20060708 (prerelease) (Debian 4.1.1-8)) #1 SMP Mon Jul 17 12:45:08 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff74000 (usable)
BIOS-e820: 000000003ff74000 - 000000003ff76000 (ACPI NVS)
BIOS-e820: 000000003ff76000 - 000000003ff97000 (ACPI data)
BIOS-e820: 000000003ff97000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
1023MB LOWMEM available.
found SMP MP-table at 000fe710
On node 0 totalpages: 262004
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 257908 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000feb90
ACPI: RSDT (v001 DELL WS 360 0x00000008 ASL 0x00000061) @ 0x000fd164
ACPI: FADT (v001 DELL WS 360 0x00000008 ASL 0x00000061) @ 0x000fd19c
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffc8d51
ACPI: MADT (v001 DELL WS 360 0x00000008 ASL 0x00000061) @ 0x000fd210
ACPI: BOOT (v001 DELL WS 360 0x00000008 ASL 0x00000061) @ 0x000fd27c
ACPI: ASF! (v016 DELL WS 360 0x00000008 ASL 0x00000061) @ 0x000fd2a4
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2793.443 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030716k/1048016k available (1478k kernel code, 16660k reserved, 540k data, 164k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5592.05 BogoMIPS (lpj=11184110)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 1 processors activated (5592.05 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 5122k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfba82, last bus=2
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0a: ioport range 0x800-0x85f could not be reserved
pnp: 00:0a: ioport range 0xc00-0xc7f has been reserved
pnp: 00:0a: ioport range 0x860-0x8ff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: fe900000-feafffff
PREFETCH window: d8000000-efffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: fe800000-fe8fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
audit: initializing netlink socket (disabled)
audit(1153224714.796:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 USB2 USB3 PCI1 KBD
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 164k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Intel(R) PRO/1000 Network Driver - version 7.0.33-k2-NAPI
Copyright (c) 1999-2005 Intel Corporation.
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 18 (level, low) -> IRQ 169
ieee1394: Initialized config rom entry `ip1394'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
e1000: 0000:02:0c.0: e1000_probe: (PCI:33MHz:32-bit) 00:0c:f1:89:ea:a8
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 177
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[fe8db800-fe8dbfff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 185, io base 0x0000ff80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 1.20 loaded.
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 193, io base 0x0000ff60
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000ff40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 185, io base 0x0000ff20
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xffa80800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide1...
hdc: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000000000000f1]
ide1 at 0x170-0x177,0x376 on irq 15
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 169
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 169
hdc: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata1: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3e01 87:4003 88:207f
ata1: dev 0 ATA-6, max UDMA/133, 234375000 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ata2: SATA port has no device.
scsi1 : ata_piix
Vendor: ATA Model: ST3120026AS Rev: 8.05
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 234375000 512-byte hdwr sectors (120000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 234375000 512-byte hdwr sectors (120000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: sda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 670462
ext3_orphan_cleanup: deleting unreferenced inode 1987708
ext3_orphan_cleanup: deleting unreferenced inode 1987668
ext3_orphan_cleanup: deleting unreferenced inode 1985339
ext3_orphan_cleanup: deleting unreferenced inode 1984642
ext3_orphan_cleanup: deleting unreferenced inode 670509
ext3_orphan_cleanup: deleting unreferenced inode 1984457
ext3_orphan_cleanup: deleting unreferenced inode 686827
ext3_orphan_cleanup: deleting unreferenced inode 1474021
ext3_orphan_cleanup: deleting unreferenced inode 3452270
ext3_orphan_cleanup: deleting unreferenced inode 3793718
ext3_orphan_cleanup: deleting unreferenced inode 3793712
ext3_orphan_cleanup: deleting unreferenced inode 3793710
ext3_orphan_cleanup: deleting unreferenced inode 3793705
ext3_orphan_cleanup: deleting unreferenced inode 3793701
EXT3-fs: sda1: 15 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Real Time Clock Driver v1.12ac
hw_random hardware driver 1.0.0 loaded
input: PC Speaker as /class/input/input1
EDAC MC: Ver: 2.0.0 Jul 17 2006
EDAC i82875p: i82875p init one
PCI: Unable to reserve mem region #1:1000@fecf0000 for device 0000:00:06.0
EDAC MC0: Giving out device to "i82875p_edac" i82875p: PCI 0000:00:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55586 usecs
intel8x0: clocking to 48000
EXT3 FS on sda1, internal journal
Probing IDE interface ide0...
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 524280k swap on /swapfile. Priority:-1 extents:140 across:1306072k
NET: Registered protocol family 15
e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
ip_tables: (C) 2000-2006 Netfilter Core Team
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [VBTN]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
device eth0 entered promiscuous mode
audit(1153224786.274:2): dev=eth0 prom=256 old_prom=0 auid=4294967295
eth0: no IPv6 routers present
nacctd uses obsolete (PF_INET,SOCK_PACKET)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
powernow: This module only works with AMD K7 CPUs
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 185
[drm] Initialized radeon 1.24.0 20060225 on minor 0
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 7105 using kernel context 0
mice: PS/2 mouse device common for all mice
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 16819 using kernel context 0
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 4 ports detected
usb 3-2.2: new low speed USB device using uhci_hcd and address 3
usb 3-2.2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-2.2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ts: Compaq touchscreen protocol output
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 18019 using kernel context 0
usb 3-2: USB disconnect, address 2
usb 3-2.2: USB disconnect, address 3
[drm] Module unloaded
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 185
[drm] Initialized radeon 1.24.0 20060225 on minor 0
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 18850 using kernel context 0
[drm] Module unloaded
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 185
[drm] Initialized radeon 1.24.0 20060225 on minor 0
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 19073 using kernel context 0
Reply to: