Bug#240146: Acknowledgement (xserver-xfree86: crashes on ATi Radeon IGP340M during start)
See attachment.
Best regards,
Milan Jurik00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
Flags: bus master, 66Mhz, medium devsel, latency 64
Memory at ec000000 (32-bit, prefetchable) [size=64M]
Memory at e8013000 (32-bit, prefetchable) [size=4K]
Capabilities: [a0] AGP version 2.0
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e8100000-e81fffff
Prefetchable memory behind bridge: f8000000-fbffffff
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
Subsystem: IBM: Unknown device 0540
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at e8010000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
00:03.0 Modem: ALi Corporation Intel 537 [M5457 AC-Link Modem] (prog-if 00 [Generic])
Subsystem: IBM: Unknown device 0535
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at e8011000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 8400 [size=256]
Capabilities: [40] Power Management version 2
00:04.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
Subsystem: IBM: Unknown device 053e
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at 8800 [size=256]
Memory at e8012000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
00:06.0 Bridge: ALi Corporation M7101 PMU
Subsystem: IBM: Unknown device 053c
Flags: medium devsel
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: IBM: Unknown device 053b
Flags: bus master, medium devsel, latency 0
Capabilities: [a0] Power Management version 1
00:0b.0 Ethernet controller: Broadcom Corporation: Unknown device 170d (rev 01)
Subsystem: IBM: Unknown device 0545
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at e8000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
00:0c.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
Subsystem: IBM: Unknown device 0528
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if fa)
Subsystem: IBM: Unknown device 053d
Flags: bus master, medium devsel, latency 0
I/O ports at 8080 [size=16]
Capabilities: [60] Power Management version 2
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon IGP 340M (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 053a
Flags: bus master, stepping, fast Back2Back, 66Mhz, medium devsel, latency 66, IRQ 11
Memory at f8000000 (32-bit, prefetchable) [size=64M]
I/O ports at d000 [size=256]
Memory at e8100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Capabilities: [50] Power Management version 2
Linux version 2.6.4 (root@tsbook) (gcc version 3.3.3 (Debian)) #1 Wed Mar 17 09:56:37 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ef70000 (usable)
BIOS-e820: 000000000ef70000 - 000000000ef7b000 (ACPI data)
BIOS-e820: 000000000ef7b000 - 000000000ef7d000 (ACPI NVS)
BIOS-e820: 000000000ef80000 - 000000000f000000 (reserved)
BIOS-e820: 000000001ef80000 - 000000001f000000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
239MB LOWMEM available.
On node 0 totalpages: 61296
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 57200 pages, LIFO batch:13
HighMem zone: 0 pages, LIFO batch:1
DMI present.
IBM machine detected. Enabling interrupts during APM calls.
IBM machine detected. Disabling SMBus accesses.
ACPI: RSDP (v002 IBM ) @ 0x000f6d90
ACPI: XSDT (v001 IBM TP-1S 0x00001270 LTP 0x00000000) @ 0x0ef749ff
ACPI: FADT (v003 IBM TP-1S 0x00001270 IBM 0x00000001) @ 0x0ef74b00
ACPI: SSDT (v001 IBM TP-1S 0x00001270 MSFT 0x0100000e) @ 0x0ef74cb4
ACPI: ECDT (v001 IBM TP-1S 0x00001270 IBM 0x00000001) @ 0x0ef7aec5
ACPI: BOOT (v001 IBM TP-1S 0x00001270 LTP 0x00000001) @ 0x0ef7afd8
ACPI: DSDT (v001 IBM TP-1S 0x00001270 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=Linux ro root=302
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 2192.615 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Memory: 237888k/245184k available (2817k kernel code, 6580k reserved, 929k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4358.14 BogoMIPS
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.20GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd84c, last bus=4
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040220
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 2)
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: the driver 'system' has been registered
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f6de0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9d73, dseg 0x400
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: 00:01: ioport range 0x370-0x371 has been reserved
pnp: 00:01: ioport range 0x15e0-0x15ef has been reserved
pnp: 00:01: ioport range 0x1600-0x167f has been reserved
pnp: match found with the PnP device '00:02' and the driver 'system'
pnp: match found with the PnP device '00:0b' and the driver 'system'
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0x40b-0x40b has been reserved
pnp: 00:0b: ioport range 0x480-0x48f has been reserved
pnp: 00:0b: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0b: ioport range 0x8000-0x803f has been reserved
pnp: 00:0b: ioport range 0x8040-0x807f could not be reserved
pnp: match found with the PnP device '00:0c' and the driver 'system'
pnp: match found with the PnP device '00:0d' and the driver 'system'
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
SCSI subsystem initialized
ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: No IRQ known for interrupt pin A of device 0000:00:0f.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=14.32 MHz (RefDiv=31) Memory=183.00 Mhz, System=133.00 MHz
i2c_adapter i2c-0: registered as adapter #0
i2c_adapter i2c-1: registered as adapter #1
i2c_adapter i2c-2: registered as adapter #2
i2c_adapter i2c-3: registered as adapter #3
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
Non-DDC laptop panel detected
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
radeonfb: Monitor 1 type LCD found
radeonfb: Monitor 2 type no found
radeonfb: panel ID string: 1024x768
radeonfb: detected LVDS panel size from BIOS: 1024x768
radeondb: BIOS provided dividers will be used
radeonfb: Power Management enabled for Mobility chipsets
mtrr: base(0xf8000000) is not aligned on a size(0x3000000) boundary
radeonfb: ATI Radeon C7 SDR SGRAM 48 MB
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
Simple Boot Flag 0x1
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
SGI XFS with ACLs, security attributes, no debug enabled
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Using anticipatory io scheduler
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ACPI: No IRQ known for interrupt pin A of device 0000:00:0f.0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N030ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: DW-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 52754229 sectors (27010 MB)
native capacity is 58605120 sectors (30005 MB)
hda: 52754229 sectors (27010 MB) w/1740KiB Cache, CHS=55824/15/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 1658kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 17
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI: (supports S0 S3 S4 S5)
XFS mounting filesystem hda2
Ending clean XFS mount for filesystem: hda2
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
blk: queue ced7e800, I/O limit 4095Mb (mask 0xffffffff)
hdc: CHECK for good STATUS
Adding 514040k swap on /dev/hda5. Priority:-1 extents:1
bcm5700: no version for "struct_module" found: kernel tainted.
Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension (NICE) ver. 7.1.9 (11/03/03)
eth0: Broadcom BCM5901 100Base-TX found at mem e8000000, IRQ 11, node addr 00061bdfd4a6
eth0: Broadcom BCM5705 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, TSO ON
Non-volatile memory driver v1.2
thinkpad: I have registered to handle major: 10 minor: 170.
smapi: 32-bit protected mode SMAPI BIOS found. :-)
Linux agpgart interface v0.100 (c) Dave Jones
[drm] Initialized radeon 1.10.0 20020828 on minor 0: ATI Radeon RS200 Mobility IGP 340M
NTFS driver 2.1.6 [Flags: R/W MODULE].
NTFS volume version 3.1.
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: irq 11, pci mem d08f5000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit flow control ON
slamr: module license 'Smart Link Ltd.' taints kernel.
slamr: SmartLink AMRMO modem.
slamr: probe 10b9:5457 SL1800 card...
slamr: mc97 codec is SIL27
slamr: slamr0 is SL1800 card.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0466da0(lo)
IPv6 over IPv4 tunneling driver
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:00:0c.0 [1014:0528]
Yenta: ISA IRQ mask 0x04f8, PCI irq 11
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f 0x3b8-0x3df 0x480-0x48f
cs: IO port probe 0x0a00-0x0aff: clean.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
cdrom: This disc doesn't have any tracks I recognize!
Reply to: