On Tue, 2016-02-16 at 19:00 +0530, Ritesh Raj Sarraf wrote: > A couple days ago, I removed the smartmontools package. I suspected > that that may be causing trouble. For the last couple days, my klog > was > clean and I was tempted to report. I installed smartmontools again, and ran some commands manually. And have some concerning report. And I think the reporting may be correct because where my HDD is located, temperature may be high. -- Ritesh Raj Sarraf RESEARCHUT - http://www.researchut.com "Necessity is the mother of invention."
smartctl 6.4 2014-10-07 r4002 [armv7l-linux-4.1.16-v7+] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda Green (AF)
Device Model: ST2000DL001-9VT156
Serial Number: 5YD0S8LQ
LU WWN Device Id: 5 000c50 02ec00d59
Firmware Version: CC96
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5900 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Feb 16 19:12:26 2016 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error medium or hardware error (serious)
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 633) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 348) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 552224292
3 Spin_Up_Time 0x0003 093 092 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4253
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 62050510
9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 10634
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 767
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 096 096 000 Old_age Always - 4
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 25770197000
189 High_Fly_Writes 0x003a 094 094 000 Old_age Always - 6
190 Airflow_Temperature_Cel 0x0022 044 039 045 Old_age Always FAILING_NOW 56 (Min/Max 24/59 #2345)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 66
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 6983
194 Temperature_Celsius 0x0022 056 061 000 Old_age Always - 56 (0 19 0 0 0)
195 Hardware_ECC_Recovered 0x001a 123 099 000 Old_age Always - 552224292
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 8
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 5786 (251 0 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2995904255
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1995971153
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 10633 hours (443 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 da 08 ff ff ff 4f 00 9d+22:59:30.548 READ DMA EXT
25 da 20 ff ff ff 4f 00 9d+22:59:30.524 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:27.183 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.907 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.906 READ DMA EXT
Error 3 occurred at disk power-on lifetime: 10633 hours (443 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 da 08 ff ff ff 4f 00 9d+22:59:27.183 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.907 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.906 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.905 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.905 READ DMA EXT
Error 2 occurred at disk power-on lifetime: 10633 hours (443 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 da 08 ff ff ff 4f 00 9d+22:59:23.907 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.906 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.905 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.905 READ DMA EXT
25 da 08 ff ff ff 4f 00 9d+22:59:23.905 READ DMA EXT
Error 1 occurred at disk power-on lifetime: 10633 hours (443 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 da f0 ff ff ff 4f 00 9d+22:59:20.172 READ DMA EXT
25 da f0 ff ff ff 4f 00 9d+22:59:20.168 READ DMA EXT
25 da f0 ff ff ff 4f 00 9d+22:59:20.164 READ DMA EXT
35 da 40 ff ff ff 4f 00 9d+22:59:20.162 WRITE DMA EXT
35 da f0 ff ff ff 4f 00 9d+22:59:20.158 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8279 -
# 2 Short offline Aborted by host 50% 8279 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Attachment:
signature.asc
Description: This is a digitally signed message part