Re: problem whit optic fibre adapter (emulex LP952)
Can we get some relevant dmesg and /var/log/boot output? Also, are you loading
libfc? You'll need it in addition to lpfc.
Have you tried building a custom kernel with all the stuff built in, not as modules?
--
Stan
Marco Vaschetto put forth on 1/19/2010 2:35 AM:
> Stan Hoeppner ha scritto:
>> Marco Vaschetto put forth on 1/16/2010 6:38 PM:
>>
>>
>>> Jan 14 14:10:28 ssdsmb1tls kernel: lpfc 0000:03:01.0: 0:0442 Adapter
>>> failed to init, mbxCmd x88 CONFIG_PORT, mbxStatus x12 Data: x0
>>> Jan 14 14:10:28 ssdsmb1tls kernel: lpfc 0000:03:01.0: 0:0442 Adapter
>>> failed to init, mbxCmd x88 CONFIG_PORT, mbxStatus x12 Data: x0"
>>>
>>
>> This could be caused by any number of things. Send complete lspci (no
>> switches)
>> output and we'll go from there.
>>
>>
> Hi,
>
> this is the complite output of lspci -vv
>
> 00:00.0 Host bridge: Broadcom GCNB-LE Host Bridge (rev 32)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Kernel modules: sworks-agp
>
> 00:00.1 Host bridge: Broadcom GCNB-LE Host Bridge
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Kernel modules: sworks-agp
>
> 00:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
> (prog-if 00 [VGA controller])
> Subsystem: Compaq Computer Corporation Proliant Rage XL
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping+ SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (2000ns min), Cache Line Size: 64 bytes
> Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: I/O ports at 2400 [size=256]
> Region 2: Memory at f5ff0000 (32-bit, non-prefetchable) [size=4K]
> [virtual] Expansion ROM at 98040000 [disabled] [size=128K]
> Capabilities: [5c] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702X
> Gigabit Ethernet (rev 02)
> Subsystem: Compaq Computer Corporation NC7760 Gigabit Server
> Adapter (PCI-X, 10/100/1000-T)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (16000ns min), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 19
> Region 0: Memory at f5fe0000 (64-bit, non-prefetchable) [size=64K]
> [virtual] Expansion ROM at 98060000 [disabled] [size=64K]
> Capabilities: [40] PCI-X non-bridge device
> Command: DPERE- ERO- RBC=512 OST=1
> Status: Dev=ff:1f.1 64bit+ 133MHz+ SCD- USC- DC=simple
> DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data <?>
> Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+
> Queue=0/3 Enable-
> Address: 084280808000409c Data: 14a6
> Kernel driver in use: tg3
> Kernel modules: tg3
>
> 00:05.0 System peripheral: Compaq Computer Corporation Advanced System
> Management Controller
> Subsystem: Compaq Computer Corporation Device b0f3
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 1800 [size=256]
> Region 1: Memory at f5fd0000 (32-bit, non-prefetchable) [size=256]
>
> 00:06.0 RAID bus controller: Compaq Computer Corporation Smart Array
> 64xx (rev 01)
> Subsystem: Compaq Computer Corporation Smart Array 641
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 21
> Region 0: Memory at f5fc0000 (64-bit, non-prefetchable) [size=8K]
> Region 2: I/O ports at 2800 [size=256]
> Region 3: Memory at f5f80000 (64-bit, non-prefetchable) [size=256K]
> [virtual] Expansion ROM at 98000000 [disabled] [size=256K]
> Capabilities: [d0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [dc] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=2048 OST=8
> Status: Dev=fd:01.0 64bit+ 133MHz+ SCD- USC- DC=simple
> DMMRBC=2048 DMOST=8 DMCRS=128 RSCEM- 266MHz- 533MHz-
> Capabilities: [f0] Vital Product Data <?>
> Kernel driver in use: cciss
> Kernel modules: cciss
>
> 00:07.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05)
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> I/O behind bridge: 00003000-00003fff
> Memory behind bridge: f7800000-f7bfffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Kernel modules: shpchp
>
> 00:08.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05)
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 00004000-00004fff
> Memory behind bridge: f7c00000-f7ffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Kernel modules: shpchp
>
> 00:09.0 Fibre Channel: Emulex Corporation LP952 Fibre Channel Host
> Adapter (rev 01)
> Subsystem: Emulex Corporation LP952 Fibre Channel Host Adapter
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 27
> Region 0: Memory at f5f70000 (64-bit, non-prefetchable) [size=4K]
> Region 2: Memory at f5f60000 (64-bit, non-prefetchable) [size=256]
> Region 4: I/O ports at 2c00 [size=256]
> Kernel modules: lpfc
>
> 00:0e.0 IDE interface: Broadcom CSB6 IDE Controller (rev a0) (prog-if 82
> [Master PriP])
> Subsystem: Broadcom Device 0213
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64
> Interrupt: pin ? routed to IRQ 14
> Region 0: I/O ports at 01f0 [size=8]
> Region 1: I/O ports at 03f4 [size=1]
> Region 2: I/O ports at 0170 [size=8]
> Region 3: I/O ports at 0374 [size=1]
> Region 4: I/O ports at 2000 [size=16]
> Capabilities: [b0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: Serverworks_IDE
> Kernel modules: serverworks
>
> 00:0f.0 ISA bridge: Broadcom CSB6 South Bridge (rev a0)
> Subsystem: Broadcom Device 0201
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR- INTx-
> Latency: 32
> Kernel driver in use: piix4_smbus
> Kernel modules: i2c-piix4
>
> 00:0f.2 USB Controller: Broadcom CSB6 OHCI USB Controller (rev 05)
> (prog-if 10 [OHCI])
> Subsystem: Broadcom Device 0220
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (20000ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at f5f50000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
>
> 00:0f.3 Host bridge: Broadcom GCLE-2 Host Bridge
> Subsystem: Broadcom Device 0230
> Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Kernel modules: sworks-agp
>
> 01:04.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet
> Pro 100 (rev 08)
> Subsystem: Compaq Computer Corporation NC3134 Fast Ethernet NIC (dual
> port)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 23
> Region 0: Memory at f7bf0000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at 3000 [size=64]
> Region 2: Memory at f7a00000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> Kernel driver in use: e100
> Kernel modules: eepro100, e100
>
> 01:05.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet
> Pro 100 (rev 08)
> Subsystem: Compaq Computer Corporation NC3134 Fast Ethernet NIC (dual
> port)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 24
> Region 0: Memory at f79f0000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at 3040 [size=64]
> Region 2: Memory at f7800000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> Kernel driver in use: e100
> Kernel modules: eepro100, e100
>
> 02:04.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet
> Pro 100 (rev 08)
> Subsystem: Compaq Computer Corporation NC3134 Fast Ethernet NIC (dual
> port)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 25
> Region 0: Memory at f7ff0000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at 4000 [size=64]
> Region 2: Memory at f7e00000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> Kernel driver in use: e100
> Kernel modules: eepro100, e100
>
> 02:05.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet
> Pro 100 (rev 08)
> Subsystem: Compaq Computer Corporation NC3134 Fast Ethernet NIC (dual
> port)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 26
> Region 0: Memory at f7df0000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at 4040 [size=64]
> Region 2: Memory at f7c00000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> Kernel driver in use: e100
> Kernel modules: eepro100, e100
>
> tank's.
>
> Marco Vaschetto
>
>
Reply to: