Re: hdb status error, dma disabled by itself on hda and hdb
Hugo Vanwoerkom wrote:
The last time I saw this it was the end of my disk.
What does
/usr/sbin/smartctl -a -d ata /dev/hdb
say?
Hugo
Here it is what it says:
##################################################
~# /usr/sbin/smartctl -s on -a -d ata /dev/hdb
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar SE family
Device Model: WDC WD1200JB-00DUA3
Serial Number: WD-WMACM2151885
Firmware Version: 75.13B75
User Capacity: 120,034,123,776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Feb 21 17:24:18 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (4335) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 59) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0007 148 146 021 Pre-fail
Always - 3616
4 Start_Stop_Count 0x0032 095 095 040 Old_age
Always - 5209
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail
Always - 0
9 Power_On_Hours 0x0032 070 070 000 Old_age
Always - 22350
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 467
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always
- 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
##################################################
So, how does it look?
thanks,
->HS
Reply to: