Re: Etch, Xorg, reconfigure
Am Sonntag, 10. September 2006 12:46 schrieb Kevin Mark:
> On Sun, Sep 10, 2006 at 12:33:23PM +0200, Bernd Kloss wrote:
> > Hi,
> > trying to make a clone, I have problems reconfiguring Xserver using
> > dpkg-reconfigure xserver-xorg
> >
> > lspci on target reports:
> > 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome
> > Pro VGA Adapter (rev 01)
> >
> > lspci on source reports:
> > 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY
> > [Radeon 7000/VE]
> >
> > /var/log/Xorg.0.log on target reads:
> >
> > (==) Log file: "/var/log/Xorg.0.log", Time: Sat Sep 9 20:30:33 2006
> > (==) Using config file: "/etc/X11/xorg.conf"
> > (==) ServerLayout "Default Layout"
> > (**) |-->Screen "Default Screen" (0)
> > (**) | |-->Monitor "Standardbildschirm"
> > (**) | |-->Device "ATI Technologies, Inc. Radeon RV100 QY [Radeon
> > 7000/VE]" (**) |-->Input Device "Generic Keyboard"
> > (**) |-->Input Device "Configured Mouse"
> > (WW) The directory "/usr/X11R6/lib/X11/fonts/misc" does not exist.
> > Entry deleted from font path.
> > II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
> >
> > .......................................many..............................
> >....... ATI Radeon X850 XT PE (R480) (PCIE),
> > ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 SE (R480)
> > (AGP), ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 XT PE (R480)
> > (AGP) (II) Primary Device is: PCI 01:00:0
> > (II) ATI: Candidate "Device" section "ATI Technologies, Inc. Radeon
> > RV100 QY [Radeon 7000/VE]".
> > (II) ATI: Shared non-ATI VGA in PCI/AGP slot 1:0:0 detected.
> > (EE) No devices detected.
> > Fatal server error:
> > no screens found
> >
> > To me this means, that there is still the source-graphics installed.
> >
> > I tryed to dpkg-reconfigure xserver-xorg, but could not find the right
> > settings. What to do?
> > Thanks for helping.
>
> Hi Bernd,
> first, you did not say HOW you cloned the system. But it would seem that
> you did not setup the target system with the correct video setting.
> the source server has a ati radeon 7000/ve and
> the target server has a S3 Unicrome Pro
> If you ran 'dpkg-reconfigure xserver-xorg', you would try to find a
> diffrent setting. i'm not sure what the best setting is, but you can
> always start with the basic 'vesa' driver. Google for a more featurefull
> driver. The source card can use: vesa,ati or radeon. The message seems
> to say that you setup the target with one of these settings. Also,
> sometimes you may need a 'lower level' reconfigure, this is done with
> 'dpkg-reconfigure -plow xserver-xorg'.
> Cheer,
> Kev
Hi, Kev,
thank you, but I did not succeed.
Cloning:
find -depth ! -path "./data/*" | cpio -a -o -H crc -V | gzip -f | split -b
4000m --verbose - ./sicher/hda1-09-09-06B.cpio.gz
Changing the settings:
I tried
sudo dpkg-reconfigure -phigh xserver-xorg
as well as
sudo dpkg-reconfigure -plow xserver-xorg
The answer always is:
xserver-xorg postinst warning: not updateing /etc/X11/X : file has been
customized
I tried VESA and VGA. There is another client under SuSE 9.3 and the xorg.conf
says: VESA, Framebuffer. Putting these settings into the Debian-Client did
not help, because a fbdev is missing
What to do about that???
Thank you.
Reply to: