Debian hostap USB prism2 : HELP
Hi,
I am trying to get a USB Linksys, Inc. WUSB12v1.1 802.11b which uses
the Prism2 chipset to work on a debian system 2.4.27-2-386 using the
hostap driver.
Running lsusb I get
Bus 001 Device 001: ID 0000:0000
Bus 001 Device 002: ID 066b:2213 Linksys, Inc. WUSB12v1.1 802.11b
Adapter
So I figure the hardware is at least being seen
ls /lib/modules/2.4.27-2-386/net
hostap_crypt_ccmp.o
hostap_crypt_tkip.o
hostap_crypt_wep.o
hostap.o
hostap_pci.o
hostap_plx.o
This is my current lsmod, doing a modprobe hostap
Adds hostap to the top of the list
Module Size Used by Not tainted
input 3040 0 (autoclean)
apm 8428 1 (autoclean)
aes 31488 1 (autoclean)
airo_cs 3108 0 (unused)
airo 38776 1 [airo_cs]
ds 5844 4 [airo_cs]
appletalk 17796 12 (autoclean)
parport_pc 19432 1 (autoclean)
lp 5540 0 (autoclean)
parport 21608 1 (autoclean) [parport_pc lp]
af_packet 11048 2 (autoclean)
ipt_REJECT 3160 1 (autoclean)
ipt_MASQUERADE 1304 1 (autoclean)
ipt_state 504 3 (autoclean)
iptable_mangle 2040 0 (autoclean) (unused)
iptable_nat 14766 1 (autoclean) [ipt_MASQUERADE]
ip_conntrack 17000 0 (autoclean) [ipt_MASQUERADE ipt_state
iptable_nat]
iptable_filter 1644 1 (autoclean)
ip_tables 10400 8 [ipt_REJECT ipt_MASQUERADE ipt_state
iptable_mangle iptable_nat iptable_filter]
usb-uhci 19504 0 (unused)
usbcore 52268 1 [usb-uhci]
maestro3 23152 1
ac97_codec 11252 0 [maestro3]
soundcore 3268 2 [maestro3]
ide-scsi 8272 0
sym53c8xx_2 58592 0 (unused)
scsi_mod 86052 2 [ide-scsi sym53c8xx_2]
3c59x 23312 1
yenta_socket 8804 4
pcmcia_core 38020 0 [airo_cs ds yenta_socket]
agpgart 39108 0 (unused)
ide-cd 27072 0
cdrom 26212 0 [ide-cd]
rtc 5768 0 (autoclean)
ext3 65388 1 (autoclean)
jbd 34628 1 (autoclean) [ext3]
ide-detect 288 0 (autoclean) (unused)
piix 7784 1 (autoclean)
ide-disk 12448 2 (autoclean)
cmd64x 6596 1 (autoclean)
ide-core 91832 2 (autoclean) [ide-scsi ide-cd
ide-detect piix ide-disk cmd64x]
unix 12752 202 (autoclean)
This is the part where I loose the plot, how do I associate the hostap
with the hardware so that it is visable in an ifconfig -a so I can
add an IP address and all the other good stuff.
This is my current ifconfig, I have an Ethernet card wired connecting
and a cisco pcmcia card 802.11b which both worked fine straight from
the install.
Been banging my head against this for a couple of weeks and I'm not
getting anywhere.
Appreciate any hints, ideas, solutions or good places to look or other
fun commands I can mess with.
Thanks for your time.
eth0 Link encap:Ethernet HWaddr 00:00:86:44:DD:D6
inet addr:192.168.1.100 Bcast:192.168.1.255
Mask:255.255.255.0
EtherTalk Phase 2 addr:65280/7
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:79 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
RX bytes:1240 (1.2 KiB) TX bytes:9296 (9.0 KiB)
eth1 Link encap:Ethernet HWaddr 00:09:7C:14:A2:FA
inet addr:192.168.200.109 Bcast:192.168.200.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:22 errors:1650 dropped:0 overruns:0 frame:1650
TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
collisions:15
RX bytes:2469 (2.4 KiB) TX bytes:7139 (6.9 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
EtherTalk Phase 2 addr:0/0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6872 errors:0 dropped:0 overruns:0 frame:0
TX packets:6872 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
RX bytes:565433 (552.1 KiB) TX bytes:565433 (552.1 KiB)
wifi0 Link encap:UNSPEC HWaddr
00-09-7C-14-A2-FA-00-00-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:2312 Metric:1
RX packets:22 errors:1650 dropped:0 overruns:0 frame:1650
TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
collisions:15
RX bytes:2469 (2.4 KiB) TX bytes:7139 (6.9 KiB)
Reply to: