Promise Ultra 100 TX2
Hi im having problems with the Promise Controller mentioned above.
The controller is installed :) and two hds are connected...
Above some informations any help is appreciated
uname -r
2.4.22-xfs
as a text file attached my dmesg
fdisk /dev/hde
Konnte /dev/hde nicht lessen (in engl: cant read /dev/hde)
root@fileserver:/proc/ide# ls
drivers hda hdc hdd hde hdf ide0 ide1 ide2 pdc202xx pdcnew
via
root@fileserver:/proc/ide# more pdc202xx
Ultra100 on M/B Chipset.
------------------------------- General Status
---------------------------------
Burst Mode : disabled
Host Mode : Normal
Bus Clocking : 33 PCI Internal
IO pad select : 10 mA
Status Polling Period : 0
Interrupt Check Status Polling Delay : 0
--------------- Primary Channel ---------------- Secondary Channel
-------------
enabled enabled
66 Clocking disabled disabled
Mode PCI Mode PCI
FIFO Empty FIFO Empty
--------------- drive0 --------- drive1 -------- drive0 ----------
drive1 ------
DMA enabled: no no no no
DMA Mode: NOTSET NOTSET NOTSET
NOTSET
PIO Mode: NOTSET NOTSET NOTSET
NOTSET
root@fileserver:/proc/ide# more pdcnew
Ultra100 TX2 Chipset.
With best regards
Michael Schlembach
I've stopped 7.594 spam messages. You can too!
One month FREE spam protection at www.cloudmark.com
Linux version 2.4.22-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Fr Okt 3 20:36:25 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=knoppix ro root=1601 hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1485.274 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2962.22 BogoMIPS
Memory: 515104k/524224k available (1262k kernel code, 8732k reserved, 534k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU0: AMD Unknown CPU Type stepping 00
per-CPU timeslice cutoff: 731.32 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1485.2551 MHz.
..... host bus clock speed is 270.0464 MHz.
cpu: 0, clocks: 2700464, slice: 1350232
CPU0<T0:2700464,T1:1350224,D:8,S:1350232,C:2700464>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb400, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3099] at 00:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe4000000, mapped to 0xe080d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:be80
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20268: IDE controller at PCI slot 00:0b.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:pio, hdh:pio
PDC20265: IDE controller at PCI slot 00:0f.0
PCI: Enabling device 00:0f.0 (0000 -> 0003)
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
ide4: BM-DMA at 0xb800-0xb807, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0xb808-0xb80f, BIOS settings: hdk:pio, hdl:pio
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1
ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
hdc: SAMSUNG SV1204H, ATA DISK drive
hdd: MAXTOR 4K060H3, ATA DISK drive
hde: SAMSUNG SP1604N, ATA DISK drive
hdf: Maxtor 6Y060L0, ATA DISK drive
hdf: set_drive_speed_status: status=0xff { Busy }
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0x9400-0x9407,0x9802 on irq 10
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 234493056 sectors (120060 MB) w/2048KiB Cache, CHS=232632/16/63
hdd: attached ide-disk driver.
hdd: host protected area => 1
hdd: 117266688 sectors (60041 MB) w/2000KiB Cache, CHS=116336/16/63
hde: attached ide-disk driver.
hde: status timeout: status=0xff { Busy }
hde: drive not ready for command
hde: host protected area => 1
hde: status timeout: status=0xff { Busy }
hde: drive not ready for command
hde: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63
hde: status timeout: status=0xff { Busy }
hde: drive not ready for command
hdf: attached ide-disk driver.
hdf: status timeout: status=0xff { Busy }
hdf: drive not ready for command
hdf: host protected area => 1
hdf: 120103200 sectors (61493 MB) w/2048KiB Cache, CHS=119150/16/63
hdf: status timeout: status=0xff { Busy }
hdf: drive not ready for command
ide-cd: passing drive hda to ide-scsi emulation.
hda: attached ide-scsi driver.
spurious 8259A interrupt: IRQ7.
Partition check:
hdc: hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 hdc9 >
hdd: hdd1
hde:hde: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
hde: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev 21:00 (hde), sector 0
end_request: I/O error, dev 21:00 (hde), sector 2
end_request: I/O error, dev 21:00 (hde), sector 4
end_request: I/O error, dev 21:00 (hde), sector 6
end_request: I/O error, dev 21:00 (hde), sector 0
end_request: I/O error, dev 21:00 (hde), sector 2
end_request: I/O error, dev 21:00 (hde), sector 4
end_request: I/O error, dev 21:00 (hde), sector 6
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, dev 21:00 (hde), sector 0
end_request: I/O error, dev 21:00 (hde), sector 2
end_request: I/O error, dev 21:00 (hde), sector 4
end_request: I/O error, dev 21:00 (hde), sector 6
unable to read partition table
hdf:hdf: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
hdf: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev 21:40 (hdf), sector 0
end_request: I/O error, dev 21:40 (hdf), sector 2
end_request: I/O error, dev 21:40 (hdf), sector 4
end_request: I/O error, dev 21:40 (hdf), sector 6
end_request: I/O error, dev 21:40 (hdf), sector 0
end_request: I/O error, dev 21:40 (hdf), sector 2
end_request: I/O error, dev 21:40 (hdf), sector 4
end_request: I/O error, dev 21:40 (hdf), sector 6
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, dev 21:40 (hdf), sector 0
end_request: I/O error, dev 21:40 (hdf), sector 2
end_request: I/O error, dev 21:40 (hdf), sector 4
end_request: I/O error, dev 21:40 (hdf), sector 6
unable to read partition table
ide: late registration of driver.
end_request: I/O error, dev 21:00 (hde), sector 312576640
pdcraid: Error reading superblock.
end_request: I/O error, dev 21:40 (hdf), sector 120103136
pdcraid: Error reading superblock.
end_request: I/O error, dev 21:00 (hde), sector 312576640
pdcraid: Error reading superblock.
end_request: I/O error, dev 21:40 (hdf), sector 120103136
pdcraid: Error reading superblock.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
end_request: I/O error, dev 21:00 (hde), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 21:40 (hdf), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 21:00 (hde), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 21:40 (hdf), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 21:00 (hde), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 21:40 (hdf), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 21:00 (hde), sector 8
hptraid: Error reading superblock.
Guestimating sector 234492031 for superblock
Guestimating sector 117259183 for superblock
Guestimating sector 312560384 for superblock
end_request: I/O error, dev 21:00 (hde), sector 312560384
silraid: Error reading superblock.
Guestimating sector 120102175 for superblock
end_request: I/O error, dev 21:40 (hdf), sector 120102168
silraid: Error reading superblock.
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1002
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 144k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
Adding Swap: 4882712k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,1), internal journal
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:50:29 Oct 3 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xc000, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0dba000, 00:40:f4:1e:c4:11, IRQ 5
eth0: Identified 8139 chip type 'RTL-8139C'
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
SGI XFS snapshot 2.4.22-2003-09-03_04:09_UTC with ACLs, realtime, no debug enabled
SGI XFS Quota Management subsystem
NTFS driver v1.1.22 [Flags: R/W MODULE]
EFS: 1.0a - http://aeschi.ch.eu.org/efs/
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
hde: set_drive_speed_status: status=0xff { Busy }
hde: set_drive_speed_status: status=0xff { Busy }
blk: queue c0335438, I/O limit 4095Mb (mask 0xffffffff)
hdf: set_drive_speed_status: status=0xff { Busy }
hdf: set_drive_speed_status: status=0xff { Busy }
blk: queue c0335580, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0334fcc, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0335114, I/O limit 4095Mb (mask 0xffffffff)
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: Printer, Samsung ML-6060
lp0: using parport0 (polling).
lp0: console ready
end_request: I/O error, dev 21:00 (hde), sector 0
end_request: I/O error, dev 21:40 (hdf), sector 0
end_request: I/O error, dev 21:00 (hde), sector 0
end_request: I/O error, dev 21:00 (hde), sector 0
ide-scsi: hda: unsupported command in request queue (0)
end_request: I/O error, dev 03:00 (hda), sector 0
ide-scsi: hda: unsupported command in request queue (0)
end_request: I/O error, dev 03:00 (hda), sector 2
ide-scsi: hda: unsupported command in request queue (0)
end_request: I/O error, dev 03:00 (hda), sector 4
ide-scsi: hda: unsupported command in request queue (0)
end_request: I/O error, dev 03:00 (hda), sector 6
Reply to: