Re: D-link DFE-530tx
Quoting Rob Weir <rweir@ertius.org>:
> On Sat, Nov 01, 2003 at 12:03:54PM +0100, Kurt Sys said
> > Hello,
> >
> > I have to install a new computer. I install Debian Woody (3.0r1) from
> > boot-CD (CD1 -- NON-US). Everything works fine except for one thing, I can't
> > get my ethernet card to work. I found on the net several people with similar
> > or the same problem, but I don't find an answer. So, here it is (again).
> > The network card is a D-link DFE-530tx. Following different sources, I need
> > the via-rhine module, but this won't work. Any other driver also doesn't
> > work.
[...snip...]
> This usually means the module is already loaded, or in the case of the
> Debian install kernels, that the module is built in. Have you checked
> "dmesg" to see if your card is already detected?
Hi,
Thanks for your reply (and the replies of others, but no, I didn't check 'dmesg'
yet. I add here some more output. I upgraded to kernel 2.4.18 (which is on CD1
also), and tried the most obvious possibilities (via-rhine, sundance and realtek
modules). I didn't include any of them in the kernel, so they won't be in the
kernel, I guess, and they cannot be inserted as a module.
tnx,
Kurt.
---- lsmod ----
Module Size Used by Not tainted
ufs 48224 0 (unused)
umsdos 23680 0 (unused)
msdos 4924 0 [umsdos]
udf 77952 0 (unused)
vfat 9340 1
dummy 928 0 (unused)
-----
----- dmesg -----
[... upper part cropped ....]
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24db
PCI: Device 00:1f.1 not available because of resource collisions
PCI_IDE: chipset revision 2
PCI_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
PCI_IDE: unknown IDE controller on PCI bus 00 device fa, VID=8086, DID=24d1
PCI_IDE: chipset revision 2
PCI_IDE: 100% native mode on irq 18
ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:pio, hdh:pio
hda: Maxtor 6Y060L0, ATA DISK drive
hdc: CDU5211, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 120103200 sectors (61493 MB) w/2048KiB Cache, CHS=119150/16/63
hdc: ATAPI 52X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: [PTBL] [7476/255/63] hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 hda11
hda12 hda13 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Unsupported Intel chipset (device id: 2570), you might want to try
agp_try_unsupported=1.
agpgart: no supported devices found.
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] Initialized radeon 1.1.1 20010405 on minor 1
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
es1371: version v0.30 time 14:56:19 Nov 1 2003
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64
uhci.c: USB UHCI at I/O 0xcc00, IRQ 16
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
uhci.c: USB UHCI at I/O 0xd000, IRQ 19
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
uhci.c: USB UHCI at I/O 0xd400, IRQ 18
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
uhci.c: USB UHCI at I/O 0xd800, IRQ 16
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 240k freed
Adding Swap: 2080408k swap-space (priority -1)
via-rhine.c:v1.10-LK1.1.13 Nov-17-2001 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
8139too Fast Ethernet driver 0.9.24
ne.c: You must supply "io=0xNNN" value(s) for ISA cards.
via-rhine.c:v1.10-LK1.1.13 Nov-17-2001 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/drivers.html
8139too Fast Ethernet driver 0.9.24
atp.c:v1.09 8/9/2000 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/atp.html
sundance.c:v1.01b 17-Jan-2002 Written by Donald Becker
http://www.scyld.com/network/sundance.html
via-rhine.c:v1.10-LK1.1.13 Nov-17-2001 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
via-rhine.c:v1.10-LK1.1.13 Nov-17-2001 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
sundance.c:v1.01b 17-Jan-2002 Written by Donald Becker
http://www.scyld.com/network/sundance.html
8139too Fast Ethernet driver 0.9.24
atp.c:v1.09 8/9/2000 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/atp.html
eth0: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
ne.c: You must supply "io=0xNNN" value(s) for ISA cards.
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/drivers.html
udf: registering filesystem
-----
Reply to: