Re: boot list

[Manoj Srivastava <srivasta@debian.org>]

Hi,

	Here is the lilo.conf from my laptop, please note that
 multiple images are referenced, beyond the two that make-kpkg
 manages. 

	manoj

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda2

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda5

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
#
install=/boot/boot-bmp.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=50

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#

#message=/etc/lilo.message
        prompt
        single-key
        timeout=300

# Four keywords are added to 'lilo.conf' to allow the usage of bitmap
# screens
bitmap=/boot/debian.bmp
bmp-table=30p,100p,1,18,
bmp-colors=15,,11,8,,15
bmp-timer=366p,329p,6,8,0

##verbose = 3

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=Linux

image = /vmlinuz
        label = Linux
        read-only
        alias=1

image = /vmlinuz.old
        label = LinuxOLD
        optional
        read-only
        alias=2

image = /vmlinuz.stable
        label = Stable
        optional
        read-only
        alias=3

image = /vmlinuz.unstable
        label = Unstable
        optional
        read-only
        alias=4

image=/boot/linux
        label=Rescue
        root=/dev/ram0
        initrd=/boot/root.bin
        optional
        append="load_ramdisk=1 mem=127M"
        alias=5

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#       label=HURD
#       restricted
#       alias=6

other=/dev/hda1
        label=Win2k
        table = /dev/hda
        alias=6


-- 
 All life evolves by the differential survival of replicating
 entities. Dawkins
Manoj Srivastava   <srivasta@debian.org>  <http://www.debian.org/%7Esrivasta/>
1024R/C7261095 print CB D9 F4 12 68 07 E4 05  CC 2D 27 12 1D F5 E8 6E
1024D/BF24424C print 4966 F272 D093 B493 410B  924B 21BA DABB BF24 424C