ATI problems
Hi Folks,
I am having real trouble with configuring my ATI 128 Ultra card. I did
search through the list archive and found references but they could not help
me out. I have just made a fresh install on a system.
Gdm refuses to start and when manually started it says fatal error no
screens found.
I tried XFreee86 -configure. It says it has found a valid configuration but
unfortunately the appropriate data has not been added to xf86PciInfo.h and
says to forward scanpic -v to the XFree 86 team.
I would appreciate some help on this.
Thank you
regards
Harshu.
pci bus 0x0 cardnum 0x00 function 0x0000: vendor 0x8086 device 0x1a30
Intel Device unknown
CardVendor 0x1028 card 0x0110 (Card unknown)
STATUS 0x2090 COMMAND 0x0106
CLASS 0x06 0x00 0x00 REVISION 0x03
pci bus 0x0 cardnum 0x01 function 0x0000: vendor 0x8086 device 0x1a31
Intel Device unknown
STATUS 0x00a0 COMMAND 0x0107
CLASS 0x06 0x04 0x00 REVISION 0x03
HEADER 0x01 LATENCY 0x40
PRIBUS 0x00 SECBUS 0x01 SUBBUS 0x01 SECLT 0x40
IOBASE 0xe000 IOLIM 0xefff SECSTATUS 0x02a0
NOPREFETCH_MEMBASE 0xff900000 MEMLIM 0xffafffff
PREFETCH_MEMBASE 0xf8000000 MEMLIM 0xfbffffff
NO_FAST_B2B NO_SEC_BUS_RST NO_M_ABRT VGA_EN ISA_EN NO_PERR_EN
pci bus 0x0 cardnum 0x1e function 0x0000: vendor 0x8086 device 0x244e
Intel Device unknown
STATUS 0x0080 COMMAND 0x0107
CLASS 0x06 0x04 0x00 REVISION 0x12
HEADER 0x01 LATENCY 0x00
PRIBUS 0x00 SECBUS 0x02 SUBBUS 0x02 SECLT 0x40
IOBASE 0xd000 IOLIM 0xdfff SECSTATUS 0xa280
NOPREFETCH_MEMBASE 0xff700000 MEMLIM 0xff8fffff
PREFETCH_MEMBASE 0xfff00000 MEMLIM 0x000fffff
NO_FAST_B2B NO_SEC_BUS_RST NO_M_ABRT NO_VGA_EN ISA_EN NO_PERR_EN
pci bus 0x0 cardnum 0x1f function 0x0000: vendor 0x8086 device 0x2440
Intel Device unknown
STATUS 0x0280 COMMAND 0x000f
CLASS 0x06 0x01 0x00 REVISION 0x12
HEADER 0x80 LATENCY 0x00
pci bus 0x0 cardnum 0x1f function 0x0001: vendor 0x8086 device 0x244b
Intel Device unknown
CardVendor 0x1028 card 0x0110 (Card unknown)
STATUS 0x0280 COMMAND 0x0005
CLASS 0x01 0x01 0x80 REVISION 0x12
BASE4 0x0000ffa1 addr 0x0000ffa0 I/O
BYTE_0 0xe307e307 BYTE_1 0x00 BYTE_2 0x806c968 BYTE_3 0xffffffff
pci bus 0x0 cardnum 0x1f function 0x0002: vendor 0x8086 device 0x2442
Intel Device unknown
CardVendor 0x1028 card 0x0110 (Card unknown)
STATUS 0x0280 COMMAND 0x0005
CLASS 0x0c 0x03 0x00 REVISION 0x12
BASE4 0x0000ff81 addr 0x0000ff80 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x04 INT_LINE 0x0b
pci bus 0x0 cardnum 0x1f function 0x0003: vendor 0x8086 device 0x2443
Intel Device unknown
CardVendor 0x1028 card 0x0110 (Card unknown)
STATUS 0x0280 COMMAND 0x0001
CLASS 0x0c 0x05 0x00 REVISION 0x12
BASE4 0x0000ccd1 addr 0x0000ccd0 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x02 INT_LINE 0x0a
BYTE_0 0x01 BYTE_1 0x00 BYTE_2 0x806d058 BYTE_3 0xffffffff
pci bus 0x0 cardnum 0x1f function 0x0004: vendor 0x8086 device 0x2444
Intel Device unknown
CardVendor 0x1028 card 0x0110 (Card unknown)
STATUS 0x0280 COMMAND 0x0005
CLASS 0x0c 0x03 0x00 REVISION 0x12
BASE4 0x0000ff61 addr 0x0000ff60 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x03 INT_LINE 0x09
pci bus 0x0 cardnum 0x1f function 0x0005: vendor 0x8086 device 0x2445
Intel Device unknown
CardVendor 0x1028 card 0x0110 (Card unknown)
STATUS 0x0280 COMMAND 0x0005
CLASS 0x04 0x01 0x00 REVISION 0x12
BASE0 0x0000c801 addr 0x0000c800 I/O
BASE1 0x0000cc41 addr 0x0000cc40 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x02 INT_LINE 0x0a
pci bus 0x1 cardnum 0x00 function 0x0000: vendor 0x1002 device 0x5446
ATI Device unknown
CardVendor 0x1002 card 0x0408 (ATI, Card unknown)
STATUS 0x02b0 COMMAND 0x0083
CLASS 0x03 0x00 0x00 REVISION 0x00
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x10
BASE0 0xf8000008 addr 0xf8000000 MEM PREFETCHABLE
BASE1 0x0000ec01 addr 0x0000ec00 I/O
BASE2 0xff9fc000 addr 0xff9fc000 MEM
BASEROM 0x80000000 addr 0x80000000 not-decode-enabled
MAX_LAT 0x00 MIN_GNT 0x08 INT_PIN 0x01 INT_LINE 0x03
pci bus 0x2 cardnum 0x09 function 0x0000: vendor 0x1282 device 0x9102
Device unknown
CardVendor 0x4554 card 0x434e (Card unknown)
STATUS 0x8210 COMMAND 0x0107
CLASS 0x02 0x00 0x00 REVISION 0x31
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0x0000dc01 addr 0x0000dc00 I/O
BASE1 0xff7ffc00 addr 0xff7ffc00 MEM
BASEROM 0xff800000 addr 0xff800000 not-decode-enabled
MAX_LAT 0x28 MIN_GNT 0x14 INT_PIN 0x01 INT_LINE 0x0b
BYTE_0 0x28000000 BYTE_1 0x00 BYTE_2 0x806de38 BYTE_3 0xffffffff
This is a pre-release version of XFree86, and is not supported in any
way. Bugs may be reported to XFree86@XFree86.Org and patches submitted
to fixes@XFree86.Org. Before reporting bugs in pre-release versions,
please check the latest version in the XFree86 CVS repository
(http://www.XFree86.Org/cvs)
XFree86 Version 4.1.0.1 / X Window System
(protocol Version 11, revision 0, vendor release 6510)
Release Date: 21 December 2001
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/FAQ)
Build Operating System: Linux 2.4.17 i686 [ELF]
Module Loader present
(==) Log file: "/var/log/XFree86.0.log", Time: Sat Nov 23 05:11:18 2002
(--) using VT number 7
(WW) Cannot open APM
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.4
XFree86 XInput driver : 0.2
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.2
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.2
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.4
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,1a30 card 1028,0110 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 8086,1a31 card 0000,0000 rev 03 class 06,04,00 hdr 01
(II) PCI: 00:1e:0: chip 8086,244e card 0000,0000 rev 12 class 06,04,00 hdr 01
(II) PCI: 00:1f:0: chip 8086,2440 card 0000,0000 rev 12 class 06,01,00 hdr 80
(II) PCI: 00:1f:1: chip 8086,244b card 1028,0110 rev 12 class 01,01,80 hdr 00
(II) PCI: 00:1f:2: chip 8086,2442 card 1028,0110 rev 12 class 0c,03,00 hdr 00
(II) PCI: 00:1f:3: chip 8086,2443 card 1028,0110 rev 12 class 0c,05,00 hdr 00
(II) PCI: 00:1f:4: chip 8086,2444 card 1028,0110 rev 12 class 0c,03,00 hdr 00
(II) PCI: 00:1f:5: chip 8086,2445 card 1028,0110 rev 12 class 04,01,00 hdr 00
(II) PCI: 01:00:0: chip 1002,5446 card 1002,0408 rev 00 class 03,00,00 hdr 00
(II) PCI: 02:09:0: chip 1282,9102 card 4554,434e rev 31 class 02,00,00 hdr 00
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.4
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) PCI-to-ISA bridge:
(II) PCI-to-PCI bridge:
(II) PCI-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0e (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B]
[1] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[2] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[B]
[3] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xff900000 - 0xffafffff (0x200000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
(II) Bus 2: bridge is at (0:30:0), (0,2,2), BCTRL: 0x06 (VGA_EN is cleared)
(II) Bus 2 I/O range:
[0] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B]
[1] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[2] -1 0 0x0000d800 - 0x0000d8ff (0x100) IX[B]
[3] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0xff700000 - 0xff8fffff (0x200000) MX[B]
(II) Bus 2 prefetchable memory range:
(II) Bus -1: bridge is at (0:31:0), (0,-1,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus -1 I/O range:
(II) Bus -1 non-prefetchable memory range:
(II) Bus -1 prefetchable memory range:
(--) PCI:*(1:0:0) ATI unknown chipset (0x5446) rev 0, Mem @ 0xf8000000/26, 0xff9fc000/14, I/O @ 0xec00/8, BIOS @ 0x80000000/17
List of video drivers:
atimisc
r128
radeon
mga
glint
nv
tga
s3virge
sis
rendition
neomagic
i740
tdfx
savage
cirrus
vmware
tseng
trident
chips
apm
glide
fbdev
i128
ati
i810
imstt
ark
cyrix
siliconmotion
vesa
vga
v4l
(II) LoadModule: "atimisc"
(II) Loading /usr/X11R6/lib/modules/drivers/atimisc_drv.o
(II) Module atimisc: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 6.3.6
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "r128"
(II) Loading /usr/X11R6/lib/modules/drivers/r128_drv.o
(II) Module r128: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 4.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "radeon"
(II) Loading /usr/X11R6/lib/modules/drivers/radeon_drv.o
(II) Module radeon: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 4.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "mga"
(II) Loading /usr/X11R6/lib/modules/drivers/mga_drv.o
(II) Module mga: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "glint"
(II) Loading /usr/X11R6/lib/modules/drivers/glint_drv.o
(II) Module glint: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "nv"
(II) Loading /usr/X11R6/lib/modules/drivers/nv_drv.o
(II) Module nv: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "tga"
(II) Loading /usr/X11R6/lib/modules/drivers/tga_drv.o
(II) Module tga: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "s3virge"
(II) Loading /usr/X11R6/lib/modules/drivers/s3virge_drv.o
(II) Module s3virge: vendor="Kevin Brosius"
compiled for 4.1.0.1, module version = 1.6.13
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "sis"
(II) Loading /usr/X11R6/lib/modules/drivers/sis_drv.o
(II) Module sis: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 0.6.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "rendition"
(II) Loading /usr/X11R6/lib/modules/drivers/rendition_drv.o
(II) Module rendition: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 4.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "neomagic"
(II) Loading /usr/X11R6/lib/modules/drivers/neomagic_drv.o
(II) Module neomagic: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "i740"
(II) Loading /usr/X11R6/lib/modules/drivers/i740_drv.o
(II) Module i740: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "tdfx"
(II) Loading /usr/X11R6/lib/modules/drivers/tdfx_drv.o
(II) Module tdfx: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "savage"
(II) Loading /usr/X11R6/lib/modules/drivers/savage_drv.o
(II) Module savage: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.1.16
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "cirrus"
(II) Loading /usr/X11R6/lib/modules/drivers/cirrus_drv.o
(II) Module cirrus: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "vmware"
(II) Loading /usr/X11R6/lib/modules/drivers/vmware_drv.o
(II) Module vmware: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 10.4.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "tseng"
(II) Loading /usr/X11R6/lib/modules/drivers/tseng_drv.o
(II) Module tseng: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "trident"
(II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o
(II) Module trident: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "chips"
(II) Loading /usr/X11R6/lib/modules/drivers/chips_drv.o
(II) Module chips: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "apm"
(II) Loading /usr/X11R6/lib/modules/drivers/apm_drv.o
(II) Module apm: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "glide"
(II) Loading /usr/X11R6/lib/modules/drivers/glide_drv.o
(II) Module glide: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) Loading sub module "glide2x"
(II) LoadModule: "glide2x"
(WW) Warning, couldn't open module glide2x
(II) UnloadModule: "glide2x"
(EE) Glide driver:
Could not load the shared library file for Glide: "libglide2x.so"!
You need to have Glide installed to run the glide driver for XFree86.
Also, you need to tell XFree86 where the libglide2x.so file is placed
by making a soft link in the /usr/X11R6/lib/modules directory that points
to the libglide2x.so file. For example (if your libglide2x.so file is in
/usr/lib):
# ln -s /usr/lib/libglide2x.so /usr/X11R6/lib/modules
(II) UnloadModule: "glide"
(II) Unloading /usr/X11R6/lib/modules/drivers/glide_drv.o
(EE) Failed to load module "glide" (submodule could not be loaded, 2)
(II) LoadModule: "fbdev"
(II) Loading /usr/X11R6/lib/modules/drivers/fbdev_drv.o
(II) Module fbdev: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "i128"
(II) Loading /usr/X11R6/lib/modules/drivers/i128_drv.o
(II) Module i128: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "ati"
(II) Loading /usr/X11R6/lib/modules/drivers/ati_drv.o
(II) Module ati: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 6.3.6
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "i810"
(II) Loading /usr/X11R6/lib/modules/drivers/i810_drv.o
(II) Module i810: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "imstt"
(II) Loading /usr/X11R6/lib/modules/drivers/imstt_drv.o
(II) Module imstt: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "ark"
(II) Loading /usr/X11R6/lib/modules/drivers/ark_drv.o
(II) Module ark: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 0.5.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "cyrix"
(II) Loading /usr/X11R6/lib/modules/drivers/cyrix_drv.o
(II) Module cyrix: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "siliconmotion"
(II) Loading /usr/X11R6/lib/modules/drivers/siliconmotion_drv.o
(II) Module siliconmotion: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.2.2
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "vesa"
(II) Loading /usr/X11R6/lib/modules/drivers/vesa_drv.o
(II) Module vesa: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "vga"
(II) Loading /usr/X11R6/lib/modules/drivers/vga_drv.o
(II) Module vga: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 4.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.4
(II) LoadModule: "v4l"
(II) Loading /usr/X11R6/lib/modules/drivers/linux/v4l_drv.o
(II) Module v4l: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 0.0.1
ABI class: XFree86 Video Driver, version 0.4
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) Active PCI resource ranges:
[0] -1 0 0xff7ffc00 - 0xff7ffcff (0x100) MX[B]
[1] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B]
[2] -1 0 0x80000000 - 0x8001ffff (0x20000) MX[B](B)
[3] -1 0 0xff9fc000 - 0xff9fffff (0x4000) MX[B](B)
[4] -1 0 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[5] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[6] -1 0 0x0000cc40 - 0x0000cc7f (0x40) IX[B]
[7] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B]
[8] -1 0 0x0000ff60 - 0x0000ff7f (0x20) IX[B]
[9] -1 0 0x0000ccd0 - 0x0000ccdf (0x10) IX[B]
[10] -1 0 0x0000ff80 - 0x0000ff9f (0x20) IX[B]
[11] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B]
[12] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xff7ffc00 - 0xff7ffcff (0x100) MX[B]
[1] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B]
[2] -1 0 0x80000000 - 0x8001ffff (0x20000) MX[B](B)
[3] -1 0 0xff9fc000 - 0xff9fffff (0x4000) MX[B](B)
[4] -1 0 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[5] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[6] -1 0 0x0000cc40 - 0x0000cc7f (0x40) IX[B]
[7] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B]
[8] -1 0 0x0000ff60 - 0x0000ff7f (0x20) IX[B]
[9] -1 0 0x0000ccd0 - 0x0000ccdf (0x10) IX[B]
[10] -1 0 0x0000ff80 - 0x0000ff9f (0x20) IX[B]
[11] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B]
[12] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xff7ffc00 - 0xff7ffcff (0x100) MX[B]
[6] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B]
[7] -1 0 0x80000000 - 0x8001ffff (0x20000) MX[B](B)
[8] -1 0 0xff9fc000 - 0xff9fffff (0x4000) MX[B](B)
[9] -1 0 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[13] -1 0 0x0000cc40 - 0x0000cc7f (0x40) IX[B]
[14] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B]
[15] -1 0 0x0000ff60 - 0x0000ff7f (0x20) IX[B]
[16] -1 0 0x0000ccd0 - 0x0000ccdf (0x10) IX[B]
[17] -1 0 0x0000ff80 - 0x0000ff9f (0x20) IX[B]
[18] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B]
[19] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B](B)
(II) Primary Device is: PCI 01:00:0
S3VProbe begin
(II) Loading sub module "cirrus_laguna"
(II) LoadModule: "cirrus_laguna"
(II) Loading /usr/X11R6/lib/modules/drivers/cirrus_laguna.o
(II) Module cirrus_laguna: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.4
(II) Loading sub module "cirrus_alpine"
(II) LoadModule: "cirrus_alpine"
(II) Loading /usr/X11R6/lib/modules/drivers/cirrus_alpine.o
(II) Module cirrus_alpine: vendor="The XFree86 Project"
compiled for 4.1.0.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.4
(--) VMware Guest X Server 10.4.0 - build=
CYRIX: Device Sections found: 1
Fatal server error:
XFree86 has found a valid card configuration.
Unfortunately the appropriate data has not been added to xf86PciInfo.h.
Please forward 'scanpci -v' output to XFree86 support team.
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
# File generated by xf86config.
#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
# This loads the GLX module
# Load "glx"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#
# FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# The module search path. The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "Dont Zoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
# Option "Protocol" "Xqueue"
Option "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""
# Option "XkbDisable"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc104"
Option "XkbLayout" "us"
Option "XkbVariant" "us"
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/psaux"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
# Option "Protocol" "Xqueue"
# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.
# Option "BaudRate" "9600"
# Option "SampleRate" "150"
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"
# ChordMiddle is an option for some 3-button Logitech mice
Option "ChordMiddle"
EndSection
# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "My Monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5 - 57.0
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-160
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "ATI Rage 128"
Driver "ati"
VideoRam 16384
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "ATI Rage 128"
Monitor "My Monitor"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Reply to: