Re: can't boot new kernel - VFS error
On Wednesday 25 September 2002 08:52, John Reinke wrote:
> (I'm resending this, since I don't see it in the archives for yesterday.)
>
> I've not been successful with any of the solutions to similar problems
> I've found on the web so far, so hopefully someone here can offer
> suggestions.
>
> I am unable to boot a kernel I compiled on a new woody installation. I
> used the kernel source 2.4.18 package, and I've tried compiling both the
> traditional way, and with make-kpkg, with the same results.
>
> Here's the last few lines displayed on the screen (hopefully no typos - I
> had to write it down):
>
>
> hda1: bad access: block=2, count=2
> end_request: I/O error, dev 03:01 (hda), sector 2
> EXT2-fs: unable to read superblock
> hda1: bad access: block=64, count=2
> end_request: I/O error, dev 03:01 (hda), sector 64
> isofs_read_super: bread failed, dev=03:01, iso_blknum=16, block=32
> kernel panic: VFS: Unable to mount root fs on 03:01
>
>
> Here's what I've tried so far (according to web searches):
>
> -I don't think anything is wrong with hda1. It worked with the original
> Woody install, and still works when I use a recovery floppy.
> -I have ext2, IDE, and anything else that I think is needed for booting
> compiled into the new kernel, not modules.
> -I don't have initrd settings in lilo.conf, but to my knowledge I don't
> need it.
> -My lilo.conf is virtually identical to how it was before wanting to use
> the new kernel.
>
>
> I used my config from the kernel I used on potato (2.2.x) as a guide when
> chosing options on this kernel, so I might have missed important options
> if they didn't exist them. Since Woody shipped with a 2.2.x kernel, are
> there any changes that I might need to make to the system for 2.4.x to
> work?
>
> I've included my .config file and my lilo.conf files below, since those
> might shed some light.
>
> Any suggestions?
>
> Thanks,
> John
>
>
> -----
>
> lilo.conf (comments removed):
>
>
> lba32
>
> boot=/dev/hda
>
> root=/dev/hda1
>
> install=/boot/boot-menu.b
>
> map=/boot/map
>
> delay=20
>
> vga=normal
>
> default=Linux
>
> image=/vmlinuz
> label=Linux
> read-only
> # restricted
> # alias=1
>
> image=/vmlinuz.old
> label=LinuxOLD
> read-only
> optional
> # restricted
> # alias=2
>
>
> -----
>
> kernel config:
>
>
> #
> # Automatically generated make config: don't edit
> #
> CONFIG_X86=y
> CONFIG_ISA=y
> # CONFIG_SBUS is not set
> CONFIG_UID16=y
>
> #
> # Code maturity level options
> #
> # CONFIG_EXPERIMENTAL is not set
>
> #
> # Loadable module support
> #
> CONFIG_MODULES=y
> CONFIG_MODVERSIONS=y
> CONFIG_KMOD=y
>
> #
> # Processor type and features
> #
> # CONFIG_M386 is not set
> # CONFIG_M486 is not set
> # CONFIG_M586 is not set
> # CONFIG_M586TSC is not set
> # CONFIG_M586MMX is not set
> # CONFIG_M686 is not set
> # CONFIG_MPENTIUMIII is not set
> # CONFIG_MPENTIUM4 is not set
> # CONFIG_MK6 is not set
> CONFIG_MK7=y
> # CONFIG_MELAN is not set
> # CONFIG_MCRUSOE is not set
> # CONFIG_MWINCHIPC6 is not set
> # CONFIG_MWINCHIP2 is not set
> # CONFIG_MWINCHIP3D is not set
> # CONFIG_MCYRIXIII is not set
> CONFIG_X86_WP_WORKS_OK=y
> CONFIG_X86_INVLPG=y
> CONFIG_X86_CMPXCHG=y
> CONFIG_X86_XADD=y
> CONFIG_X86_BSWAP=y
> CONFIG_X86_POPAD_OK=y
> # CONFIG_RWSEM_GENERIC_SPINLOCK is not set
> CONFIG_RWSEM_XCHGADD_ALGORITHM=y
> CONFIG_X86_L1_CACHE_SHIFT=6
> CONFIG_X86_TSC=y
> CONFIG_X86_GOOD_APIC=y
> CONFIG_X86_USE_3DNOW=y
> CONFIG_X86_PGE=y
> CONFIG_X86_USE_PPRO_CHECKSUM=y
> # CONFIG_TOSHIBA is not set
> # CONFIG_I8K is not set
> # CONFIG_MICROCODE is not set
> # CONFIG_X86_MSR is not set
> # CONFIG_X86_CPUID is not set
> CONFIG_NOHIGHMEM=y
> # CONFIG_HIGHMEM4G is not set
> # CONFIG_HIGHMEM64G is not set
> # CONFIG_MATH_EMULATION is not set
> # CONFIG_MTRR is not set
> # CONFIG_SMP is not set
> # CONFIG_X86_UP_APIC is not set
>
> #
> # General setup
> #
> CONFIG_NET=y
> CONFIG_PCI=y
> # CONFIG_PCI_GOBIOS is not set
> # CONFIG_PCI_GODIRECT is not set
> CONFIG_PCI_GOANY=y
> CONFIG_PCI_BIOS=y
> CONFIG_PCI_DIRECT=y
> CONFIG_PCI_NAMES=y
> # CONFIG_EISA is not set
> # CONFIG_MCA is not set
> CONFIG_HOTPLUG=y
>
> #
> # PCMCIA/CardBus support
> #
> # CONFIG_PCMCIA is not set
>
> #
> # PCI Hotplug Support
> #
> CONFIG_SYSVIPC=y
> CONFIG_BSD_PROCESS_ACCT=y
> CONFIG_SYSCTL=y
> CONFIG_KCORE_ELF=y
> # CONFIG_KCORE_AOUT is not set
> CONFIG_BINFMT_AOUT=y
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=y
> CONFIG_PM=y
> CONFIG_APM=y
> # CONFIG_APM_IGNORE_USER_SUSPEND is not set
> # CONFIG_APM_DO_ENABLE is not set
> # CONFIG_APM_CPU_IDLE is not set
> # CONFIG_APM_DISPLAY_BLANK is not set
> CONFIG_APM_RTC_IS_GMT=y
> # CONFIG_APM_ALLOW_INTS is not set
> # CONFIG_APM_REAL_MODE_POWER_OFF is not set
>
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
>
> #
> # Parallel port support
> #
> CONFIG_PARPORT=y
> CONFIG_PARPORT_PC=y
> CONFIG_PARPORT_PC_CML1=y
> # CONFIG_PARPORT_SERIAL is not set
> # CONFIG_PARPORT_AMIGA is not set
> # CONFIG_PARPORT_MFC3 is not set
> # CONFIG_PARPORT_ATARI is not set
> # CONFIG_PARPORT_GSC is not set
> # CONFIG_PARPORT_SUNBPP is not set
> # CONFIG_PARPORT_OTHER is not set
> # CONFIG_PARPORT_1284 is not set
>
> #
> # Plug and Play configuration
> #
> CONFIG_PNP=y
> CONFIG_ISAPNP=y
>
> #
> # Block devices
> #
> CONFIG_BLK_DEV_FD=y
> # CONFIG_BLK_DEV_XD is not set
> # CONFIG_PARIDE is not set
> # CONFIG_BLK_CPQ_DA is not set
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> # CONFIG_BLK_DEV_LOOP is not set
> # CONFIG_BLK_DEV_NBD is not set
> # CONFIG_BLK_DEV_RAM is not set
>
> #
> # Multi-device support (RAID and LVM)
> #
> # CONFIG_MD is not set
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> # CONFIG_PACKET_MMAP is not set
> CONFIG_NETLINK_DEV=y
> CONFIG_NETFILTER=y
> # CONFIG_NETFILTER_DEBUG is not set
> # CONFIG_FILTER is not set
> CONFIG_UNIX=y
> CONFIG_INET=y
> # CONFIG_IP_MULTICAST is not set
> CONFIG_IP_ADVANCED_ROUTER=y
> # CONFIG_IP_MULTIPLE_TABLES is not set
> # CONFIG_IP_ROUTE_MULTIPATH is not set
> # CONFIG_IP_ROUTE_TOS is not set
> CONFIG_IP_ROUTE_VERBOSE=y
> # CONFIG_IP_ROUTE_LARGE_TABLES is not set
> # CONFIG_IP_PNP is not set
> # CONFIG_NET_IPIP is not set
> # CONFIG_NET_IPGRE is not set
> # CONFIG_INET_ECN is not set
> CONFIG_SYN_COOKIES=y
>
> #
> # IP: Netfilter Configuration
> #
> CONFIG_IP_NF_CONNTRACK=y
> # CONFIG_IP_NF_FTP is not set
> # CONFIG_IP_NF_IRC is not set
> CONFIG_IP_NF_IPTABLES=y
> # CONFIG_IP_NF_MATCH_LIMIT is not set
> # CONFIG_IP_NF_MATCH_MAC is not set
> # CONFIG_IP_NF_MATCH_MARK is not set
> # CONFIG_IP_NF_MATCH_MULTIPORT is not set
> # CONFIG_IP_NF_MATCH_TOS is not set
> # CONFIG_IP_NF_MATCH_AH_ESP is not set
> # CONFIG_IP_NF_MATCH_LENGTH is not set
> # CONFIG_IP_NF_MATCH_TTL is not set
> # CONFIG_IP_NF_MATCH_TCPMSS is not set
> # CONFIG_IP_NF_MATCH_STATE is not set
> CONFIG_IP_NF_FILTER=y
> # CONFIG_IP_NF_TARGET_REJECT is not set
> # CONFIG_IP_NF_NAT is not set
> # CONFIG_IP_NF_MANGLE is not set
> # CONFIG_IP_NF_TARGET_LOG is not set
> # CONFIG_IP_NF_TARGET_ULOG is not set
> # CONFIG_IP_NF_TARGET_TCPMSS is not set
>
> #
> #
> #
> # CONFIG_IPX is not set
> CONFIG_ATALK=m
> # CONFIG_DECNET is not set
> # CONFIG_BRIDGE is not set
>
> #
> # QoS and/or fair queueing
> #
> # CONFIG_NET_SCHED is not set
>
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
>
> #
> # ATA/IDE/MFM/RLL support
> #
> CONFIG_IDE=y
>
> #
> # IDE, ATA and ATAPI Block devices
> #
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_HD_IDE is not set
> # CONFIG_BLK_DEV_HD is not set
> CONFIG_BLK_DEV_IDEDISK=y
> # CONFIG_IDEDISK_MULTI_MODE is not set
> # CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
> # CONFIG_BLK_DEV_COMMERIAL is not set
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> # CONFIG_BLK_DEV_IDEFLOPPY is not set
> # CONFIG_BLK_DEV_IDESCSI is not set
>
> #
> # IDE chipset support/bugfixes
> #
> CONFIG_BLK_DEV_CMD640=y
> # CONFIG_BLK_DEV_CMD640_ENHANCED is not set
> # CONFIG_BLK_DEV_ISAPNP is not set
> CONFIG_BLK_DEV_RZ1000=y
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> CONFIG_BLK_DEV_ADMA=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> CONFIG_IDEDMA_PCI_AUTO=y
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_BLK_DEV_AEC62XX is not set
> # CONFIG_BLK_DEV_ALI15X3 is not set
> # CONFIG_BLK_DEV_AMD74XX is not set
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> # CONFIG_BLK_DEV_PIIX is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_PDC202XX is not set
> # CONFIG_BLK_DEV_SVWKS is not set
> # CONFIG_BLK_DEV_SIS5513 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_VIA82CXXX is not set
> # CONFIG_IDE_CHIPSETS is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_IDEDMA_IVB is not set
> # CONFIG_DMA_NONPCI is not set
> CONFIG_BLK_DEV_IDE_MODES=y
>
> #
> # SCSI support
> #
> CONFIG_SCSI=y
>
> #
> # SCSI support type (disk, tape, CD-ROM)
> #
> CONFIG_BLK_DEV_SD=y
> CONFIG_SD_EXTRA_DEVS=40
> # CONFIG_CHR_DEV_ST is not set
> # CONFIG_CHR_DEV_OSST is not set
> # CONFIG_BLK_DEV_SR is not set
> CONFIG_CHR_DEV_SG=y
>
> #
> # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
> #
> # CONFIG_SCSI_DEBUG_QUEUES is not set
> # CONFIG_SCSI_MULTI_LUN is not set
> CONFIG_SCSI_CONSTANTS=y
> # CONFIG_SCSI_LOGGING is not set
>
> #
> # SCSI low-level drivers
> #
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_7000FASST is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AHA152X is not set
> # CONFIG_SCSI_AHA1542 is not set
> # CONFIG_SCSI_AHA1740 is not set
> CONFIG_SCSI_AIC7XXX=y
> CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
> CONFIG_AIC7XXX_RESET_DELAY_MS=15000
> # CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
> # CONFIG_SCSI_DPT_I2O is not set
> # CONFIG_SCSI_ADVANSYS is not set
> # CONFIG_SCSI_IN2000 is not set
> # CONFIG_SCSI_AM53C974 is not set
> # CONFIG_SCSI_MEGARAID is not set
> # CONFIG_SCSI_BUSLOGIC is not set
> # CONFIG_SCSI_CPQFCTS is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_DTC3280 is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_EATA_DMA is not set
> # CONFIG_SCSI_EATA_PIO is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_GENERIC_NCR5380 is not set
> # CONFIG_SCSI_IPS is not set
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_PPA is not set
> # CONFIG_SCSI_IMM is not set
> # CONFIG_SCSI_NCR53C406A is not set
> # CONFIG_SCSI_NCR53C7xx is not set
> # CONFIG_SCSI_SYM53C8XX_2 is not set
> # CONFIG_SCSI_NCR53C8XX is not set
> # CONFIG_SCSI_SYM53C8XX is not set
> # CONFIG_SCSI_PAS16 is not set
> # CONFIG_SCSI_PCI2000 is not set
> # CONFIG_SCSI_PCI2220I is not set
> # CONFIG_SCSI_PSI240I is not set
> # CONFIG_SCSI_QLOGIC_FAS is not set
> # CONFIG_SCSI_QLOGIC_ISP is not set
> # CONFIG_SCSI_QLOGIC_FC is not set
> # CONFIG_SCSI_QLOGIC_1280 is not set
> # CONFIG_SCSI_SEAGATE is not set
> # CONFIG_SCSI_SIM710 is not set
> # CONFIG_SCSI_SYM53C416 is not set
> # CONFIG_SCSI_DC390T is not set
> # CONFIG_SCSI_T128 is not set
> # CONFIG_SCSI_U14_34F is not set
> # CONFIG_SCSI_ULTRASTOR is not set
>
> #
> # Fusion MPT device support
> #
> # CONFIG_FUSION is not set
> # CONFIG_FUSION_BOOT is not set
> # CONFIG_FUSION_ISENSE is not set
> # CONFIG_FUSION_CTL is not set
> # CONFIG_FUSION_LAN is not set
>
> #
> # I2O device support
> #
> # CONFIG_I2O is not set
>
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
>
> #
> # ARCnet devices
> #
> # CONFIG_ARCNET is not set
>
> #
> # Appletalk devices
> #
> # CONFIG_APPLETALK is not set
> # CONFIG_LTPC is not set
> # CONFIG_COPS is not set
> # CONFIG_IPDDP is not set
> CONFIG_DUMMY=m
> # CONFIG_BONDING is not set
> # CONFIG_EQUALIZER is not set
> # CONFIG_TUN is not set
> # CONFIG_NET_SB1000 is not set
>
> #
> # Ethernet (10 or 100Mbit)
> #
> CONFIG_NET_ETHERNET=y
> # CONFIG_HAPPYMEAL is not set
> # CONFIG_SUNGEM is not set
> CONFIG_NET_VENDOR_3COM=y
> # CONFIG_EL1 is not set
> # CONFIG_EL2 is not set
> # CONFIG_ELPLUS is not set
> # CONFIG_EL3 is not set
> # CONFIG_3C515 is not set
> CONFIG_VORTEX=y
> # CONFIG_LANCE is not set
> # CONFIG_NET_VENDOR_SMC is not set
> # CONFIG_NET_VENDOR_RACAL is not set
> # CONFIG_DEPCA is not set
> # CONFIG_HP100 is not set
> # CONFIG_NET_ISA is not set
> CONFIG_NET_PCI=y
> # CONFIG_PCNET32 is not set
> # CONFIG_APRICOT is not set
> # CONFIG_CS89x0 is not set
> # CONFIG_TULIP is not set
> # CONFIG_DE4X5 is not set
> # CONFIG_DGRS is not set
> # CONFIG_DM9102 is not set
> CONFIG_EEPRO100=y
> # CONFIG_FEALNX is not set
> # CONFIG_NATSEMI is not set
> CONFIG_NE2K_PCI=y
> # CONFIG_8139TOO is not set
> # CONFIG_SIS900 is not set
> # CONFIG_EPIC100 is not set
> # CONFIG_SUNDANCE is not set
> # CONFIG_TLAN is not set
> # CONFIG_VIA_RHINE is not set
> # CONFIG_WINBOND_840 is not set
> # CONFIG_NET_POCKET is not set
>
> #
> # Ethernet (1000 Mbit)
> #
> # CONFIG_ACENIC is not set
> # CONFIG_DL2K is not set
> # CONFIG_NS83820 is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_SK98LIN is not set
> # CONFIG_FDDI is not set
> # CONFIG_PLIP is not set
> # CONFIG_PPP is not set
> # CONFIG_SLIP is not set
>
> #
> # Wireless LAN (non-hamradio)
> #
> # CONFIG_NET_RADIO is not set
>
> #
> # Token Ring devices
> #
> # CONFIG_TR is not set
> # CONFIG_NET_FC is not set
>
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
>
> #
> # Amateur Radio support
> #
> # CONFIG_HAMRADIO is not set
>
> #
> # IrDA (infrared) support
> #
> # CONFIG_IRDA is not set
>
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
>
> #
> # Old CD-ROM drivers (not SCSI, not IDE)
> #
> # CONFIG_CD_NO_IDESCSI is not set
>
> #
> # Input core support
> #
> # CONFIG_INPUT is not set
> CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
> CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_SERIAL=y
> # CONFIG_SERIAL_CONSOLE is not set
> # CONFIG_SERIAL_EXTENDED is not set
> # CONFIG_SERIAL_NONSTANDARD is not set
> CONFIG_UNIX98_PTYS=y
> CONFIG_UNIX98_PTY_COUNT=256
> CONFIG_PRINTER=y
> # CONFIG_LP_CONSOLE is not set
> # CONFIG_PPDEV is not set
>
> #
> # I2C support
> #
> # CONFIG_I2C is not set
>
> #
> # Mice
> #
> # CONFIG_BUSMOUSE is not set
> CONFIG_MOUSE=y
> CONFIG_PSMOUSE=y
> # CONFIG_82C710_MOUSE is not set
> # CONFIG_PC110_PAD is not set
>
> #
> # Joysticks
> #
> # CONFIG_INPUT_GAMEPORT is not set
>
> #
> # Input core support is needed for gameports
> #
>
> #
> # Input core support is needed for joysticks
> #
> # CONFIG_QIC02_TAPE is not set
>
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> # CONFIG_INTEL_RNG is not set
> # CONFIG_NVRAM is not set
> # CONFIG_RTC is not set
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
>
> #
> # Ftape, the floppy tape device driver
> #
> # CONFIG_FTAPE is not set
> CONFIG_AGP=y
> # CONFIG_AGP_INTEL is not set
> # CONFIG_AGP_I810 is not set
> # CONFIG_AGP_VIA is not set
> # CONFIG_AGP_AMD is not set
> # CONFIG_AGP_SIS is not set
> # CONFIG_AGP_ALI is not set
> # CONFIG_AGP_SWORKS is not set
> CONFIG_DRM=y
> CONFIG_DRM_OLD=y
>
> #
> # DRM 4.0 drivers
> #
> # CONFIG_DRM40_TDFX is not set
> # CONFIG_DRM40_GAMMA is not set
> CONFIG_DRM40_R128=y
> # CONFIG_DRM40_RADEON is not set
> # CONFIG_DRM40_I810 is not set
> # CONFIG_DRM40_MGA is not set
> # CONFIG_MWAVE is not set
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
>
> #
> # File systems
> #
> CONFIG_QUOTA=y
> # CONFIG_AUTOFS_FS is not set
> # CONFIG_AUTOFS4_FS is not set
> # CONFIG_REISERFS_FS is not set
> # CONFIG_EXT3_FS is not set
> # CONFIG_JBD is not set
> # CONFIG_FAT_FS is not set
> # CONFIG_CRAMFS is not set
> # CONFIG_TMPFS is not set
> # CONFIG_RAMFS is not set
> CONFIG_ISO9660_FS=y
> # CONFIG_JOLIET is not set
> CONFIG_ZISOFS=y
> # CONFIG_MINIX_FS is not set
> # CONFIG_VXFS_FS is not set
> # CONFIG_NTFS_FS is not set
> # CONFIG_HPFS_FS is not set
> CONFIG_PROC_FS=y
> CONFIG_DEVPTS_FS=y
> # CONFIG_ROMFS_FS is not set
> CONFIG_EXT2_FS=y
> # CONFIG_SYSV_FS is not set
> # CONFIG_UDF_FS is not set
> # CONFIG_UFS_FS is not set
>
> #
> # Network File Systems
> #
> # CONFIG_CODA_FS is not set
> # CONFIG_NFS_FS is not set
> # CONFIG_NFSD is not set
> # CONFIG_SUNRPC is not set
> # CONFIG_LOCKD is not set
> # CONFIG_SMB_FS is not set
> # CONFIG_NCP_FS is not set
> CONFIG_ZISOFS_FS=y
> CONFIG_ZLIB_FS_INFLATE=y
>
> #
> # Partition Types
> #
> CONFIG_PARTITION_ADVANCED=y
> # CONFIG_ACORN_PARTITION is not set
> # CONFIG_OSF_PARTITION is not set
> # CONFIG_AMIGA_PARTITION is not set
> # CONFIG_ATARI_PARTITION is not set
> CONFIG_MAC_PARTITION=y
> # CONFIG_MSDOS_PARTITION is not set
> # CONFIG_SGI_PARTITION is not set
> # CONFIG_ULTRIX_PARTITION is not set
> # CONFIG_SUN_PARTITION is not set
> # CONFIG_SMB_NLS is not set
> # CONFIG_NLS is not set
>
> #
> # Console drivers
> #
> CONFIG_VGA_CONSOLE=y
> # CONFIG_VIDEO_SELECT is not set
>
> #
> # Sound
> #
> CONFIG_SOUND=m
> # CONFIG_SOUND_BT878 is not set
> # CONFIG_SOUND_CMPCI is not set
> CONFIG_SOUND_EMU10K1=m
> # CONFIG_SOUND_FUSION is not set
> # CONFIG_SOUND_CS4281 is not set
> # CONFIG_SOUND_ES1370 is not set
> # CONFIG_SOUND_ES1371 is not set
> # CONFIG_SOUND_ESSSOLO1 is not set
> # CONFIG_SOUND_MAESTRO is not set
> # CONFIG_SOUND_ICH is not set
> # CONFIG_SOUND_SONICVIBES is not set
> # CONFIG_SOUND_TRIDENT is not set
> # CONFIG_SOUND_MSNDCLAS is not set
> # CONFIG_SOUND_MSNDPIN is not set
> # CONFIG_SOUND_VIA82CXXX is not set
> CONFIG_SOUND_OSS=m
> # CONFIG_SOUND_TRACEINIT is not set
> # CONFIG_SOUND_DMAP is not set
> # CONFIG_SOUND_SGALAXY is not set
> # CONFIG_SOUND_ADLIB is not set
> # CONFIG_SOUND_ACI_MIXER is not set
> # CONFIG_SOUND_CS4232 is not set
> # CONFIG_SOUND_SSCAPE is not set
> # CONFIG_SOUND_GUS is not set
> # CONFIG_SOUND_VMIDI is not set
> # CONFIG_SOUND_TRIX is not set
> # CONFIG_SOUND_MSS is not set
> # CONFIG_SOUND_MPU401 is not set
> # CONFIG_SOUND_NM256 is not set
> # CONFIG_SOUND_MAD16 is not set
> # CONFIG_SOUND_PAS is not set
> # CONFIG_SOUND_PSS is not set
> CONFIG_SOUND_SB=m
> CONFIG_SOUND_AWE32_SYNTH=m
> # CONFIG_SOUND_WAVEFRONT is not set
> # CONFIG_SOUND_MAUI is not set
> CONFIG_SOUND_YM3812=m
> # CONFIG_SOUND_OPL3SA1 is not set
> # CONFIG_SOUND_OPL3SA2 is not set
> # CONFIG_SOUND_YMFPCI is not set
> # CONFIG_SOUND_UART6850 is not set
> # CONFIG_SOUND_AEDSP16 is not set
>
> #
> # USB support
> #
> # CONFIG_USB is not set
>
> #
> # USB Controllers
> #
>
> #
> # USB Device Class drivers
> #
>
> #
> # USB Human Interface Devices (HID)
> #
>
> #
> # Input core support is needed for USB HID
> #
>
> #
> # USB Imaging devices
> #
>
> #
> # USB Multimedia devices
> #
>
> #
> # Video4Linux support is needed for USB Multimedia device support
> #
>
> #
> # USB Network adaptors
> #
>
> #
> # USB port drivers
> #
>
> #
> # USB Serial Converter support
> #
>
> #
> # USB Miscellaneous drivers
> #
>
> #
> # Kernel hacking
> #
> # CONFIG_DEBUG_KERNEL is not set
It is exactly the same problem I had! I have to use 2.4.19 and I compiled it
several times and everytime this message appeared. I installed a kernell by
apt-get; It could boot the system but with a lot of errors,( Mainly it
compains that the root filesystem is readonly)
Help us please!
Reply to: