Hi, and thanks for taking you time! Here are the outputs you asked for: Output of ´lspci -vv´: ============== 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G550 AGP (rev 01) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G550 Dual Head DDR 32Mb Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 42000000 (32-bit, prefetchable) Region 1: Memory at 40800000 (32-bit, non-prefetchable) Region 2: Memory at 40000000 (32-bit, non-prefetchable) Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1 --- Output of `scanpci -v`: =============== pci bus 0x1 cardnum 0x00 function 0x0000: vendor 0x102b device 0x2527 Matrox Device unknown CardVendor 0x102b card 0x0f84 (Matrox, Card unknown) STATUS 0x0290 COMMAND 0x0007 CLASS 0x03 0x00 0x00 REVISION 0x01 BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x08 BASE0 0x42000008 addr 0x42000000 MEM PREFETCHABLE BASE1 0x40800000 addr 0x40800000 MEM BASE2 0x40000000 addr 0x40000000 MEM MAX_LAT 0x20 MIN_GNT 0x10 INT_PIN 0x01 INT_LINE 0x0b BYTE_0 0x400a1520 BYTE_1 0x00 BYTE_2 0x806d680 BYTE_3 0xffffffff Output of `X -configure` is attached in X.CON Thanks again, Pontus ----- Original Message ----- From: "Michael Perry" <mperry@lnxpowered.org> To: <pontus.edvardsson@bredband.net> Sent: Thursday, December 27, 2001 5:42 PM Subject: Matrox G550 32mb under woody > HI- > > I only get the digest option to debian-users so please excuse the > personal followup. I will followup to the list also. One question, or > perhaps two... > > 1) when you do a X -configure, what is the final output of the command? > Does it say that a valid card was found but is not included a scanned > file? > > 2) what does lspci -vv or scanpci -v show? > > Thanks. > > -- > Michael Perry | "Do or do not; there is no try" Master Yoda > mperry@lnxpowered.org | http://www.lnxpowered.org > >
Attachment:
X.CON
Description: Binary data