OPL3-SA3 Sound problem
I have looked over the Linux HOWTO and searched the archives
but nothing seems to help. I am thinking that maybe isapnp is not
running at boot since I see no reference to it in dmesg. How
do I find out if it is? Where do I set it up to run if it isn't
running?
Below is my setup... any obvious blunders here?
***** dmesg (edited)
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
----------------------------------------------------------------------
***** lsmod
bsd_comp 3672 0 (autoclean)
nls_cp437 3880 1 (autoclean)
lockd 41720 0 (autoclean) (unused)
sunrpc 55452 0 (autoclean) [lockd]
serial 19640 1 (autoclean)
opl3 10972 0
fbcon-vga 1916 0 (unused)
ppp_deflate 38336 0
ppp 20300 2 [bsd_comp ppp_deflate]
slhc 4404 1 [ppp]
ad1848 15480 0
sound 56364 0 [opl3 ad1848]
soundcore 2440 3 [sound]
soundlow 368 0 [sound]
vfat 9408 0 (unused)
umsdos 23936 0 (unused)
unix 11336 27 (autoclean)
----------------------------------------------------------------------
***** cat /dev/sndstat
OSS/Free:3.8s2++-971130
Load type: Driver loaded as a module
Kernel: Linux localhostnl 2.2.18pre21 #1 Sat Nov 18 18:47:15 EST 2000 i586
Config options: 0
Installed drivers:
Card config:
Audio devices:
Synth devices:
Midi devices:
Timers:
0: System clock
Mixers:
----------------------------------------------------------------------
***** /etc/isapnp.conf (generated by pnpdump -c)
# $Id: pnpdump.c,v 1.21 1999/12/09 22:28:33 fox Exp $
# Release isapnptools-1.21 (library isapnptools-1.21)
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
# (for library: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR)
#
# Trying port address 0273
# Board 1 has serial identifier cb 80 86 00 01 30 00 a8 65
# Board 2 has serial identifier 84 bc a4 b5 93 30 30 72 56
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier cb 80 86 00 01 30 00 a8 65)
# Vendor Id YMH0030, Serial Number 2156265473, checksum 0xCB.
# Version 1.0, Vendor version 0.0
# ANSI string -->OPL3-SA3 Snd System<--
#
# Logical device id YMH0021
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE YMH0030/2156265473 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 1 (SIZE 8) (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 2 (SIZE 8) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
(IO 3 (SIZE 2) (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0370
# Maximum IO base address 0x0370
# IO base alignment 2 bytes
# Number of IO addresses required: 2
(IO 4 (SIZE 2) (BASE 0x0370))
# IRQ 5.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
(DMA 0 (CHANNEL 0))
# Next DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
(DMA 1 (CHANNEL 1))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0240
# Maximum IO base address 0x0240
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0240))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e80
# Maximum IO base address 0x0e80
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0e80))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 2 (SIZE 8) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0300
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0100))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0f48
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 2 (SIZE 8) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0334
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0100))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# End dependent functions
(NAME "YMH0030/2156265473[0]{OPL3-SA3 Snd System }")
(ACT Y)
))
#
# Logical device id YMH0022
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE YMH0030/2156265473 (LD 1
# Compatible device id PNPb02f
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0201
# Maximum IO base address 0x0201
# IO base alignment 1 bytes
# Number of IO addresses required: 1
(IO 0 (SIZE 1) (BASE 0x0201))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0201
# Maximum IO base address 0x0211
# IO base alignment 16 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0201))
# End dependent functions
(NAME "YMH0030/2156265473[1]{OPL3-SA3 Snd System }")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier 84 bc a4 b5 93 30 30 72 56)
# Vendor Id USR3030, Serial Number 3164910995, checksum 0x84.
# Version 1.0, Vendor version 0.0
# ANSI string -->U.S. Robotics 56K FAX INT<--
#
# Logical device id USR3030
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE USR3030/3164910995 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8))
# IRQ 3, 5 or 7.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8))
# *** Bad resource data (Clarifications 4.6.2): IRQ 2 invalid, changing to 9
# IRQ 3, 4, 5, 7 or 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8))
# *** Bad resource data (Clarifications 4.6.2): IRQ 2 invalid, changing to 9
# IRQ 3, 4, 5, 7 or 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02e8))
# *** Bad resource data (Clarifications 4.6.2): IRQ 2 invalid, changing to 9
# IRQ 3, 4, 5, 7 or 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# End dependent functions
(NAME "USR3030/3164910995[0]{U.S. Robotics 56K FAX INT}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Reply to: