Re: cdwriter configuration problems
Please fold likne in 72.
Need to compile SCSI CDrom support. I think.
Read CD-WRITING HOWTO for detail.
Osamu
On Sun, Feb 11, 2001 at 07:20:49PM -0600, Bernard and Jennifer Cohen wrote:
>
> I have been having trouble getting my cdwriter to work using xcdroast. I got it to the point of writing an audio cd when all it produced was 12 tracks of noise and a new beer coaster. When looking at the ide/scsi devices recognized by xcdroast the cdwriter is shown under both scsi and ide devices and the regular cdrom is not recognized at all. I have enclosed a what I hope is a all the relevant information as to set up. Would somebody also please provide me with some sources on module set-up particularly the instructions recognized by etc/modules.conf and how to connect all those char-major-xxx with the modules, and what modules to add to etc/modules.
> Thanks,
> Bernie Cohen
>
>
>
>
> from .config:
>
> CONFIG_BLK_DEV_FD=y
> CONFIG_BLK_DEV_IDE=y
> # CONFIG_BLK_DEV_HD_IDE is not set
> CONFIG_BLK_DEV_IDEDISK=y
> CONFIG_BLK_DEV_IDECD=m
> # CONFIG_BLK_DEV_IDETAPE is not set
> # CONFIG_BLK_DEV_IDEFLOPPY is not set
> CONFIG_BLK_DEV_IDESCSI=m
>
> # SCSI support
> #
> CONFIG_SCSI=y
> # CONFIG_BLK_DEV_SD is not set
> # CONFIG_CHR_DEV_ST is not set
> CONFIG_BLK_DEV_SR=y
> CONFIG_BLK_DEV_SR_VENDOR=y
> CONFIG_CHR_DEV_SG=y
> # CONFIG_SCSI_MULTI_LUN is not set
> CONFIG_SCSI_CONSTANTS=y
> # CONFIG_SCSI_LOGGING is not set
>
> CONFIG_ISO9660_FS=y
> CONFIG_JOLIET=y
>
> only line added to etc/modules.conf:
>
> options ide-cd ignore=hdc
>
>
> proc/modules:
>
> ppp_deflate 39392 0 (autoclean)
> bsd_comp 3880 0 (autoclean)
> ide-scsi 7144 0
> ide-cd 22904 0
> cdrom 26524 0 [ide-cd]
> sd_mod 15536 0 (unused)
> joy-analog 4808 0 (unused)
> joystick 5628 0 [joy-analog]
> softoss2 56696 0
> awe_wave 156756 0
> opl3 10952 0
> sb 32948 0
> uart401 6128 0 [sb]
> sound 56344 0 [softoss2 awe_wave opl3 sb uart401]
> soundlow 416 0 [sound]
> soundcore 2596 7 [sb sound]
>
> cdrecord -scanbus:
>
> Cdrecord 1.8 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg Schilling
> Using libscg version 'schily-0.1'
> scsibus0:
> 0,0,0 0) 'YAMAHA ' 'CRW8824E ' '1.00' Removable CD-ROM
> 0,1,0 1) *
> 0,2,0 2) *
> 0,3,0 3) *
> 0,4,0 4) *
> 0,5,0 5) *
> 0,6,0 6) *
> 0,7,0 7) *
>
>
> edited from dmesg |more:
>
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
> hda: Maxtor 91366U4, ATA DISK drive
> hdb: CD-ROM Drive/F5A, ATAPI CDROM drive
> hdc: YAMAHA CRW8824E, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: Maxtor 91366U4, 13029MB w/2048kB Cache, CHS=1661/255/63, UDMA
> Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M
> FDC 0 is a post-1991 82077
> scsi : 0 hosts.
> scsi : detected total.
>
> hdb: ATAPI 48X CD-ROM drive, 128kB Cache
> Uniform CD-ROM driver Revision: 3.11
> ide-cd: ignoring drive hdc
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> scsi : 1 host.
> Vendor: YAMAHA Model: CRW8824E Rev: 1.00
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.11
>
> this is appended to 'dmesg |more' after xcdroast has been entered and then closed:
>
> cdrom: open failed.
> VFS: Disk change detected on device ide0(3,64)
> cdrom: open failed.
> VFS: Disk change detected on device ide0(3,64)
> ide-scsi: hdc: unsupported command in request queue (0)
> end_request: I/O error, dev 16:00 (hdc), sector 0
--
+ Osamu Aoki <debian@aokiconsulting.com>, GnuPG-key: 1024D/D5DE453D +
+ Fingerprint: 814E BD64 3288 40E7 E88E 3D92 C3F8 EA94 D5DE 453D +
+ === http://www.aokiconsulting.com ======= Cupertino, CA USA === +
Reply to: