printing broken in potato install
I have just installed potato on a machine which happily
ran slink before. During the install it refused to
load the lp module---
>Error installing lp module
>/lib/modules/2.2.17/misc/lp.o:init_module:Device or resource busy
>Hint: this error can be caused by incorrect module parameters, including invalid IO or IRQ parameters
>/lib/modules/2.2.17/misc/lp.o:insmod /lib/modules/2.2.17/misc/lp.o failed
>/lib/modules/2.2.17/misc/lp.o:insmod lp failed
---so I put in parport which someone mentioned some time ago.
At bootup, if the printer is on, parport detects the
printer correctly-- see attatched dmesg log-- but when
I try to cat testfile > /dev/lp0 or lp1, bash complains
that no such devices exist.
If someone can tell me where in the fine manual to look
for help, I should be most grateful.
TIA,
Doug.
Linux version 2.2.17 (herbert@arnor) (gcc version 2.95.2 20000313 (Debian GNU/Linux)) #1 Sun Jun 25 09:24:41 EST 2000
Detected 400917 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.54 BogoMIPS
Memory: 127044k/131072k available (1732k kernel code, 416k reserved, 1740k data, 140k init)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfb330
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
apm: disabled on user request.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
loop: registered device at major 7
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC26400B, ATA DISK drive
hdd: ATAPI CD-ROM DRIVE 36X MAXIMUM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: WDC AC26400B, 6149MB w/512kB Cache, CHS=784/255/63
hdd: ATAPI 32X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi: <fdomain> Detection failed (no card)
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0
Failed initialization of WD-7000 SCSI card!
IBM MCA SCSI: No Microchannel-bus support present -> Aborting.
megaraid: v107 (December 22, 1999)
aec671x_detect:
3w-xxxx: tw_findcards(): No cards found.
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 140k freed
NET4: Unix domain sockets 1.0 for Linux NET4.0.
Adding Swap: 64224k swap-space (priority -1)
AWE32: not detected
parport0: PC-style at 0x378 (0x778) [SPP,ECP,ECPEPP,ECPPS2]
parport0: detected irq 7; use procfs to enable interrupt-driven operation.
parport_probe: succeeded
parport0: Printer, Kyocera FS-680
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256).
SLIP linefill/keepalive option.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
registered device ppp0
PPP BSD Compression module registered
PPP Deflate Compression module registered
Reply to: