config X - s3 virge

[Shao Zhang <shao@cia.com.au>]

Hi,
	I have a 4mb diamond 3d s3 virge video card. From XFree86.org, I
read that "1280x1024 at 24/32 bpp for a 4 Meg".

	However, I can only achieve 16 at 1024x768. When I try -bpp 24, I
get the following output:

	virge:/home/s2193893# X -bpp 24 :1

XFree86 Version 3.3.2.3 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: July 15 1998
        If the server is older than 6-12 months, or if your card is newer
        than the above date, look for a newer version before reporting
        problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.36 i686 [ELF] 
Configured drivers:
  S3V: accelerated server for S3 graphics adaptors (Patchlevel 0)
      s3_ViRGE
(using VT number 8)

XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keycodes: "xfree86"
(**) XKB: types: "default"
(**) XKB: compat: "default"
(**) XKB: symbols: "us(pc101)"  
(**) XKB: geometry: "pc"        
(**) XKB: rules: "xfree86"      
(**) XKB: model: "pc102"        
(**) XKB: layout: "us"          
(**) Mouse: type: PS/2, device: /dev/mouse, resolution: 100
(**) Mouse: buttons: 3          
(**) S3V: Graphics device ID: "Primary Card"
(**) S3V: Monitor ID: "Primary Monitor"
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc:unscaled,/usr/X11R6/lib/X11/fonts/75dpi:unscaled,/usr/X11R6/lib/X11/fonts/100dpi:unscaled,/usr/X11R6/lib/X11/fonts/Type1,/usr/X11R6/lib/X11/fonts/Speedo,/usr/X11R6/lib/X11/fonts/misc,/usr/X11R6/lib/X11/fonts/75dpi,/usr/X11R6/lib/X11/fonts/100dpi,/usr/X11R6/lib/X11/fonts/chinese/:unscaled,/usr/local/chinese-fonts/,unix/:7101"
(--) S3V: PCI: ViRGE rev 6, Linear FB @ 0xe0000000
(--) S3V: chipset:   ViRGE rev. 6
(--) S3V: chipset driver: s3_ViRGE
(**) S3V: videoram:  4096k      
(--) S3V: Ramdac type: s3_trio64
(--) S3V: Ramdac speed: 135 MHz  (57 MHz for 32 bpp)
(--) S3V: Using Trio32/64 programmable clock (MCLK 54.886 MHz)
(--) S3V: Maximum allowed dot-clock: 57.000 MHz
(--) S3V: Clock for mode "1024x768" is too high for the configured
hardware.
        Limit is  57.000 MHz    
                                
Fatal server error:             
No valid modes found.           


	Could someone please help me?

	THanks.

Shao.
____________________________________________________________________________
Shao Zhang - Running Debian 2.1  ___ _               _____
Department of Communications    / __| |_  __ _ ___  |_  / |_  __ _ _ _  __ _ 
University of New South Wales   \__ \ ' \/ _` / _ \  / /| ' \/ _` | ' \/ _` |
Sydney, Australia               |___/_||_\__,_\___/ /___|_||_\__,_|_||_\__, |
Email: shao@cia.com.au                                                  |___/ 
_____________________________________________________________________________