Hmmm, ok here's what I got from setserial: /dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4 /dev/ttyS1, UART: unknown, Port: 0x02f8, IRQ: 3 /dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4 /dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3 Is the problem that the UART is unknown? Someone else suggested that I uncomment a line in /etc/rc.boot/0setserial but it looked like it was already uncommented... > Did the solution (uncommenting appropriate line in > /etc/rc.boot/0setserial) I wrote to the orginal poster worked for you? Attached is some (hopefully) helpful files... -- Deniz Dogan Spencer wrote: > I received this from one person>> > > I'm using one of these without problems ... the only problem was at the > beginning because it was in com3 and the mouse in com1 and they were > sharing the same IRQ. Check setserial (man setserial) to solve the problem > > Best regards, > > Fernando Tricas > > -----Original Message----- > From: Christopher M. Wesneski <wesneski@flash.net> > To: sbend@washington.navy.mil <sbend@washington.navy.mil> > Cc: debian-user@lists.debian.org <debian-user@lists.debian.org> > Date: Sunday, August 02, 1998 3:26 PM > Subject: Re: Diamond Supra Express PNP internal modem , Linux , and you. > > > > > > >> ---------- > >> From: Christopher M. Wesneski[SMTP:WESNESKI@FLASH.NET] > >> Sent: Sunday, August 02, 1998 6:23:10 PM > >> To: sbend@washington.navy.mil > >> Cc: debian-user@lists.debian.org > >> Subject: Re: Diamond Supra Express PNP internal modem , Linux , and you. > >> Auto forwarded by a Rule > >> > >I have the exact same modem and I can't get it to work either. > > > >sbend@washington.navy.mil wrote: > > > >> Can someone please tell me if it is possible to use above modem with > >> Linux. Thank you for your assistance. > >> > >> -- > >> Unsubscribe? mail -s unsubscribe debian-user-request@lists.debian.org < > /dev/null > > > > > > > >
#! /bin/sh # /etc/rc.serial # Initializes the serial ports on your system # # Distributed with setserial version 2.10 # # Standard flags you want your serial devices to have # Examples: SAK, pgrp_lockout, session_lockout # STD_FLAGS="session_lockout" SETSERIAL=/bin/setserial echo -n "Configuring serial ports...." # Do wild interrupt detection # rtn=`${SETSERIAL} -W /dev/ttyS0 >/dev/null 2>&1` if [ $? -gt 0 ] then # Could not configure the serial port echo "failed..." echo " Trying to load the serial module manually..." insmod serial if [ $? -eq 0 ] then echo -n " Success.. retrying configuration..." rtn=`${SETSERIAL} -W /dev/ttyS0 >& /dev/null` if [ $? -gt 0 ] then echo "failed!" echo "Aborting serial configuration. Check the serial modules..." exit 1 fi fi fi # echo $rtn # # There have been multiple reports of late that the auto configuration # if the serial ports is broken with some new motherboards, especially # multi-processor ones. For this reason, all the autoconfiguration has # now been removed by default, and instead only com1 and 2 are configured. # The irqs are assigned manually. Note that we still need an automatic # test to find out what uart we are using. ${SETSERIAL} -b /dev/ttyS0 irq 4 port 0x3F8 skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} -b /dev/ttyS1 irq 3 port 0x2F8 skip_test autoconfig ${STD_FLAGS} ############################################################### # # AUTOMATIC CONFIGURATION # # Uncomment the appropriate lines below to enable auto-configuration # of a particular board. Or comment them out to disable them.... # # NOTE! Although the automatic configuration is enabled by default, # I strongly suggest that you comment out this section and use the # manual configuration section instead. It's more work to set up, but # it's more reliable. # ############################################################### # Do AUTOMATIC_IRQ probing # AUTO_IRQ=auto_irq # These are the standard COM1 through COM4 devices # # If you have an internal modem with a Rockwell Chipset, add a "skip_test" # to the /dev/ttyS3 line below. (It's not added by default because it will # screw up people with 8514 displays). # # ${SETSERIAL} -b /dev/ttyS0 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} # ${SETSERIAL} -b /dev/ttyS1 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} # # The typical user will only have 2 serial ports. To try and minimise # problems, all other configurations have been commented out! # #${SETSERIAL} -b /dev/ttyS2 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/ttyS3 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # These are for the first AST Fourport board (base address 0x1A0) # #${SETSERIAL} -b /dev/ttyS4 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS5 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS6 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS7 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # These are for the second AST Fourport board (base address 0x2A0) # #${SETSERIAL} -b /dev/ttyS8 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS9 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS10 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS11 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # These are the 3rd and 4th ports on the Accent Async board. # #${SETSERIAL} -b /dev/ttyS12 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS13 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # Usenet Serial Board II (base address 0x100) # #${SETSERIAL} -b /dev/ttyS16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # BocaBoard 4 port (BB-1004) (base address 0x100) # #${SETSERIAL} -b /dev/ttyS16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # BocaBoard 8 port (BB-1008) (base address 0x100), # or two BB-1004's (base addresses 0x100 and 0x120) # #${SETSERIAL} -b /dev/ttyS16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS20 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS21 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS22 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS23 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # BocaBoard 16 port (BB-1008), (base address 0x100), # or two BB-1008's (base addresses 0x100 and 0x140), # or four BB-1004's (base address 0x100, 0x120, 0x140, and 0x160) # # Warning --- some of these ports may conflict with the Future Domain # SCSI controller. If you want to run both the BocaBoards and the # Future Domain controller, you may need to change the port assignment # of the Bocaboards -- see below in the section on manual configuration. # #${SETSERIAL} -b /dev/ttyS16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS20 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS21 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS22 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS23 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS24 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS25 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS26 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS27 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS28 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS29 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS30 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS31 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # This enables the new multiport masking feature, which is highly recommened # for Bocaboard ports. Uncomment only the first line if you have a # BB-1004 or BB-1008. Uncomment both lines if you have a BB-2016. # These numbers assume the Bocaboard is located at address 0x100. If you # change this, remember to change the port1 and port2 addresses. # #${SETSERIAL} /dev/ttyS16 set_multiport port1 0x107 mask1 0xff match1 0 #${SETSERIAL} /dev/ttyS16 set_multiport port2 0x147 mask2 0xff match2 0 # ############################################################### # # MANUAL CONFIGURATION # # If you want to do manual configuration of one or more of your # serial ports, uncomment and modify the relevant lines. # ############################################################### # These are the standard COM1 through COM4 devices # #${SETSERIAL} -b /dev/ttyS0 uart 16450 port 0x3F8 irq 4 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS1 uart 16450 port 0x2F8 irq 3 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS2 uart 16450 port 0x3E8 irq 4 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS3 uart 16450 port 0x2E8 irq 3 ${STD_FLAGS} # These are the first set of AST Fourport ports # #${SETSERIAL} -b /dev/ttyS4 uart 16450 port 0x1A0 irq 9 fourport ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS5 uart 16450 port 0x1A8 irq 9 fourport ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS6 uart 16450 port 0x1B0 irq 9 fourport ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS7 uart 16450 port 0x1B8 irq 9 fourport ${STD_FLAGS} # These are the second set of AST Fourport ports # #${SETSERIAL} -b /dev/ttyS8 uart 16450 port 0x2A0 irq 5 fourport ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS9 uart 16450 port 0x2A8 irq 5 fourport ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS10 uart 16450 port 0x2B0 irq 5 fourport ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS11 uart 16450 port 0x2B8 irq 5 fourport ${STD_FLAGS} # These are the 3rd and 4th ports on the Accent Async board. # #${SETSERIAL} -b /dev/ttyS12 uart 16450 port 0x330 irq 4 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS13 uart 16450 port 0x338 irq 4 ${STD_FLAGS} # These are two spare devices you can use to customize for # some board which is not supported above.... #${SETSERIAL} -b /dev/ttyS14 uart XXXXX port XXXX irq X ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS15 uart XXXXX port XXXX irq X ${STD_FLAGS} # These are the ports used for either the Usenet Serial II # board, or the Boca Board 4, 8, or 16 port boards. # # Uncomment only the first 4 lines for the Usenet Serial II board, # and uncomment the first 4, 8, or all 16 lines for the # Boca Board BB-1004, BB-1008, and BB-2016 respectively. # #${SETSERIAL} -b /dev/ttyS16 uart 16550A port 0x100 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS17 uart 16550A port 0x108 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS18 uart 16550A port 0x110 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS19 uart 16550A port 0x118 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS20 uart 16550A port 0x120 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS21 uart 16550A port 0x128 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS22 uart 16550A port 0x130 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS23 uart 16550A port 0x138 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS24 uart 16550A port 0x140 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS25 uart 16550A port 0x148 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS26 uart 16550A port 0x150 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS27 uart 16550A port 0x158 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS28 uart 16550A port 0x160 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS29 uart 16550A port 0x168 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS30 uart 16550A port 0x170 irq 12 ${STD_FLAGS} #${SETSERIAL} -b /dev/ttyS31 uart 16550A port 0x178 irq 12 ${STD_FLAGS} ########################################################### # # Print the results of the serial configuration process # ########################################################### echo "done." ${SETSERIAL} -bg /dev/ttyS*
# # For details of this file format, see isapnp.conf(5) # # LD n = Logical device, ie write to reg 7 # IO n = IO descriptor n # BASE n = IO/Mem address # INT n = Interrupt req n # IRQ n = Interrupt level # MODE = line levels etc # ACT = Activate #(debug) #(IGNORECRC) #(READPORT 0x3bb) #(ISOLATE) #(IDENTIFY *) #(CONFIGURE DFX0000/1493 (LD 0 (IO 0 (BASE 0x3e8)) (INT 0 (IRQ 12 (MODE +E))) (ACT Y))) #(CONFIGURE DFX0000/1493 (LD 0 (REG 7 (PEEK)) (REG 0x30 (PEEK)))) #(CONFIGURE DFX0000/1493 (LD 1 (REG 7 (PEEK)) (REG 0x30 (PEEK)))) # Try to force logical device 2 (which doesn't exist)... #(CONFIGURE DFX0000/1493 (LD 1 (REG 7 (POKE 2) (PEEK)) (REG 0x30 (PEEK)))) # .. hence this gives an error #(CONFIGURE DFX0000/1493 (LD 2 (REG 7 (PEEK)) (REG 0x30 (PEEK)))) #(WAITFORKEY)
# $Id: pnpdump.c,v 1.1.1.2 1998/01/07 05:17:47 fred Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DNEEDNANOSLEEP # # Trying port address 0203 # Board 1 has serial identifier 9b 00 08 30 ae 81 13 b0 4e # Board 2 has serial identifier 04 1d 7a c3 f8 9c 00 8c 0e # (DEBUG) (READPORT 0x0203) (ISOLATE) (IDENTIFY *) # Card 1: (serial identifier 9b 00 08 30 ae 81 13 b0 4e) # Vendor Id SUP1381, Serial Number 536750, checksum 0x9B. # Version 1.0, Vendor version 0.0 # ANSI string -->SupraExpress 336i PnP Voice Modem<-- # # Logical device id SUP1381 # Device support I/O range check register # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE SUP1381/536750 (LD 0 # Compatible device id SUP1290 # Multiple choice time, choose one only ! # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03f8)) # IRQ 4. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02f8)) # IRQ 3. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03e8)) # IRQ 4. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02e8)) # IRQ 3. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03e8)) # IRQ 5. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02e8)) # IRQ 5. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03e8)) # IRQ 3, 4, 5, 7, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02e8)) # IRQ 3, 4, 5, 7, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03f8)) # IRQ 3, 4, 5, 7, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02f8)) # IRQ 3, 4, 5, 7, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0200)) # IRQ 3, 4, 5, 7, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # End dependent functions # (ACT Y) )) # End tag... Checksum 0x00 (OK) # Card 2: (serial identifier 04 1d 7a c3 f8 9c 00 8c 0e) # Vendor Id CTL009c, Serial Number 494584824, checksum 0x04. # Version 1.0, Vendor version 1.2 # ANSI string -->Creative SB32 PnP<-- # # Logical device id CTL0041 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL009c/494584824 (LD 0 # ANSI string -->Audio<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # IRQ 5. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 1)) # Next DMA channel 5. # 16 bit DMA only # Logical device is not a bus master # DMA may not execute in count by byte mode # DMA may execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 5)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 1 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 1 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0330)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # Number of IO addresses required: 4 # (IO 2 (BASE 0x0388)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 5, 6 or 7. # 16 bit DMA only # Logical device is not a bus master # DMA may not execute in count by byte mode # DMA may execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 5)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # Number of IO addresses required: 4 # (IO 2 (BASE 0x0388)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 5, 6 or 7. # 16 bit DMA only # Logical device is not a bus master # DMA may not execute in count by byte mode # DMA may execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 5)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0300)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 5, 6 or 7. # 16 bit DMA only # Logical device is not a bus master # DMA may not execute in count by byte mode # DMA may execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 5)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # Number of IO addresses required: 4 # (IO 2 (BASE 0x0388)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0300)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Start dependent functions: priority functional # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 5, 6 or 7. # 16 bit DMA only # Logical device is not a bus master # DMA may not execute in count by byte mode # DMA may execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 5)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 16 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0394 # IO base alignment 4 bytes # Number of IO addresses required: 4 # (IO 2 (BASE 0x0388)) # End dependent functions # (ACT Y) )) # # Logical device id CTL7002 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL009c/494584824 (LD 1 # ANSI string -->Game<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0x0200 # IO base alignment 1 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0200)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0x0208 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0200)) # End dependent functions # (ACT Y) )) # # Logical device id CTL0021 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL009c/494584824 (LD 2 # ANSI string -->WaveTable<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0620 # Maximum IO base address 0x0620 # IO base alignment 1 bytes # Number of IO addresses required: 4 # (IO 0 (BASE 0x0620)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0620 # Maximum IO base address 0x0680 # IO base alignment 32 bytes # Number of IO addresses required: 4 # (IO 0 (BASE 0x0620)) # End dependent functions # (ACT Y) )) # # Logical device id CTL2011 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL009c/494584824 (LD 3 # Compatible device id PNP0600 # ANSI string -->IDE<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # IRQ 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 10 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0168 # Maximum IO base address 0x0168 # IO base alignment 1 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0168)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x036e # Maximum IO base address 0x036e # IO base alignment 1 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x036e)) # Start dependent functions: priority acceptable # IRQ 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 11 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x01e8 # Maximum IO base address 0x01e8 # IO base alignment 1 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x01e8)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03ee # Maximum IO base address 0x03ee # IO base alignment 1 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x03ee)) # Start dependent functions: priority acceptable # IRQ 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 10 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0180 # Maximum IO base address 0x01b8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0180)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0306 # Maximum IO base address 0x033e # IO base alignment 8 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0306)) # Start dependent functions: priority functional # IRQ 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 15 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0170 # Maximum IO base address 0x0170 # IO base alignment 1 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0170)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0376 # Maximum IO base address 0x0376 # IO base alignment 1 bytes # Number of IO addresses required: 1 # (IO 1 (BASE 0x0376)) # End dependent functions # (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY)
Attachment:
Ppp.log
Description: application/unknown-content-type-log_auto_file
begin: vcard fn: Chris Wesneski n: Wesneski;Chris adr: http://wwp.mirabilis.com/8555629;;;Dallas, Texas;;;USA email;internet: wesneski@flash.net note: gunner@rubin.zenonline.com x-mozilla-cpt: ;0 x-mozilla-html: TRUE version: 2.1 end: vcard