SCSI

[Greg Green <greg@advantagecom.com>]

Hello all:

I am having problems detecting my scsi drives.  I have three drives all
jumpered correctly and I recompiled the kernel for raid5, and also for
my correct scsi controller.  I installed the correct raid145 patch, and
raidtools, and the latest linuxthreads. The problem is that I cannot
mkfs or mdcreate on these drives. I cannot even fdisk them, I keep
getting "unable to open /dev/sda."  The PC Bios detects the SCSI card on
boot up, but then Linux detects 0 scsi.  I have a NCR53875J SCSI
controller.
Below is my dmesg, I would appreciate any suggestions.
Thanks,
Greg Green

Below is my dmesg, I would appreciate any suggestions.

Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fae70
pcibios_init : BIOS32 Service Directory entry at 0xfb310
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb340
Probing PCI hardware.
Calibrating delay loop.. ok - 59.80 BogoMIPS
Memory: 63160k/65536k available (772k kernel code, 384k reserved, 1220k
data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized

Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.

Checking 'hlt' instruction... Ok.
Intel Pentium with F0 0F bug - workaround enabled.
moving IDT ...  ... done
Linux version 2.0.32 (root@ADCOMLX01) (gcc version 2.7.2.1) #1 Mon Feb 9
07:11:26 MST 1998
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
PS/2 auxiliary pointing device detected -- driver installed.
Real Time Clock Driver v1.07
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
    ide0: BM-DMA at 0xf000-0xf007
    ide1: BM-DMA at 0xf008-0xf00f
hda: ST32140A, 2015MB w/128kB Cache, CHS=1023/64/63
hdc: 655A, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
scsi : 0 hosts.
scsi : detected total.
PPP: version 2.2.0 (dynamic channel allocation)
TCP compression code copyright 1989 Regents of the University of
California
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
eth0: 3Com 3c905 Boomerang 100baseTx at 0x6100, 00:60:08:04:3c:f8, IRQ
11
  8K word-wide RAM 3:5 Rx:Tx split, autoselect/MII interface.
eth0: MII transceiver found at address 24.
  Enabling bus-master transmits and whole-frame receives.
eth0: Overriding PCI latency timer (CFLT) setting of 32, new value is
248.
3c59x.c:v0.46C 10/14/97 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
Partition check:
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 130748k swap-space (priority -1)
Module inserted $Id: cdrom.c,v 0.8 1996/08/10 10:52:11 david Exp $
eexpress.c: Module autoprobe not recommended, give io=xx.
loading device 'eth1'...
eexpress.c: Failed to register card at 0x0.





--
TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word "unsubscribe" to
debian-user-request@lists.debian.org . 
Trouble?  e-mail to templin@bucknell.edu .