Re: ag

[Murat Demirten <murat@debian.org>]

Selam,

eth0: RealTek RTL8139 Fast Ethernet at 0xa800, IRQ 0, 00:90:47:02:cf:af.

Burada görüldüğü gibi ethernet kartına Linux IRQ 0'ı veriyor. Burada
kart çalışmayacaktır. Hatta büyük olasılıkla sizde tek ethernet olmasına
rağmen aynı kartı eth1 ve irq 0 olarak siz modulunu yuklediginizde gene
taniyor.

Çözüm, eğer makinede başka bir işletim sistemi varsa windows gibi kartın
orada çalışıp çalışmadığını bir kontrol edin. Çalışıyorsa hangi irq'yu
kullandigini ogrenin.

Gene BIOS'unuz Lilo gelmeden hemen once PCI veriyolundaki device'lari
listeleyen turden ise orada Pause ile durdurun ve Network Adapter
benzeri aygıta BIOS'un hangi IRQ değerini set ettiğini not edin.

Ben donanımsal bir problem olduğunu düşünüyorum hala. Kartı farklı PCI
slotlara takıp denediniz mi?

22-05-2003 Perşembe günü saat 04:22 sularında, Mustafa Salih dedi ki:
> ifconfig .. eth0 .. gibi seyler yazdigimda temporarily unavailable
> diyor ifconfig .. eth1 .. icin de device busy diyor   modconf ile
> modulu kaldiriyorum yine yok kuruyorum yine yok   ilginc bir sey
> ifconfig dedigimde sade lo geliyor eth0 yok ifconfig eth0 dedigimde
> dogru ip ile beraber geliyor bir diger sey route dedigimde ekrana
> hicbir sey gelmiyor (127.0.0.1 de yok)   ben nerde hata yapiyorum.    
> dmesg ciktisi ise soyle   Linux version 2.2.20-idepci
> (herbert@gondolin) (gcc version 2.7.2.3) #1 Sat Apr 20 12:45:19 EST
> 2002
> BIOS-provided physical RAM map:
>  BIOS-e820: 0009f000 @ 00000000 (usable)
>  BIOS-e820: 0fefc000 @ 00100000 (usable)
> Detected 602201 kHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 1202.58 BogoMIPS
> Memory: 257636k/262128k available (1164k kernel code, 412k reserved,
> 2844k data, 72k init)
> Dentry hash table entries: 32768 (order 6, 256k)
> Buffer cache hash table entries: 262144 (order 8, 1024k)
> Page cache hash table entries: 65536 (order 6, 256k)
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> 256K L2 cache (8 way)
> CPU: L2 Cache: 256K
> CPU: Intel Pentium III (Coppermine) stepping 03
> Checking 386/387 coupling... OK, FPU using exception 16 error
> reporting.
> Checking 'hlt' instruction... OK.
> Checking for popad bug... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
> PCI: PCI BIOS revision 2.10 entry at 0xf0890
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Enabling I/O for device 00:50
> PCI: Enabling I/O for device 00:60
> PCI: Enabling memory for device 00:60
> PCI: 00:20 [1106/0596]: Work around ISA DMA hangs (00)
> Activating ISA DMA hang workarounds.
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> TCP: Hash tables configured (ehash 262144 bhash 65536)
> Starting kswapd v 1.5 
> vga16fb: initializing
> vga16fb: mapped to 0xc00a0000
> Console: switching to colour frame buffer device 80x30
> fb0: VGA16 VGA frame buffer device
> Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
> enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> pty: 256 Unix98 ptys configured
> RAM disk driver initialized:  16 RAM disks of 4096K size
> loop: registered device at major 7
> VP_IDE: IDE controller on PCI bus 00 dev 21
> VP_IDE: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
>     ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:pio, hdd:DMA
> hda: IC35L040AVER07-0, ATA DISK drive
> hdd: ASUS CD-S500/A, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: IC35L040AVER07-0, 39266MB w/1916kB Cache, CHS=5005/255/63
> hdd: ATAPI 50X CD-ROM drive, 128kB Cache
> Uniform CD-ROM driver Revision: 3.11
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> 3c59x.c 18Feb01 Donald Becker and others
> http://www.scyld.com/network/vortex.html
> pcnet32.c: PCI bios is present, checking for devices...
> rtl8139.c:v1.07 5/6/99 Donald Becker
> http://cesdis.gsfc.nasa.gov/linux/drivers/rtl8139.html
> eth0: RealTek RTL8139 Fast Ethernet at 0xa800, IRQ 0,
> 00:90:47:02:cf:af.
> via-rhine.c:v1.08b-LK1.0.1 12/14/2000  Written by Donald Becker
>   http://www.scyld.com/network/via-rhine.html
> Partition check:
>  hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
> apm: BIOS version 1.2 Flags 0x0b (Driver version 1.13)
> apm: disabled on user request.
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 72k freed
> Adding Swap: 666656k swap-space (priority -1)
> lp: no devices found
> lp: no devices found
> lp: no devices found
> lp: no devices found
> lp: no devices found
> lp: no devices found
> eth1: 8139too Fast Ethernet driver 0.9.18-pre4 Jeff Garzik
> <jgarzik@mandrakesoft.com>
> eth1: Linux-2.2 bug reports to Jens David
> <dg1kjd@afthd.tu-darmstadt.de>
> eth1: RealTek RTL8139 Fast Ethernet board found at 0xd0072000, IRQ 0
> eth1: Chip is 'RTL-8139C' - MAC address '00:90:47:02:cf:af'.