Cdbrännarproblem

[Fredrik Nilsson <hebbe@BamseFar.lodiz.nu>]

Hej 
Jag har ett rätt stort problem med min Mitsumi cdbrännare.
När jag försöker bränna något startar den upp bränningsprocessen, men när
den kommer till att börja bränna sttår den bara och söker på skivan. Det
händer ingenting. Tacksam om det vore nån som har nån aning vad det kan
vara. Har klippt in scanbus och det som cdrecord slänger ut.
Den fungerar fint att läsa ifrån. Jag kör simulerad SCSI.

 
Cdrecord release 1.8a30 Copyright (C) 1995-1999 Jörg Schilling
Using libscg version 'schily-0.1'
scsibus0:
        0,0,0     0) 'MITSUMI ' 'CR-2801TE       ' '1.07' Removable CD-ROM
        0,1,0     1) *
        0,2,0     2) *
        0,3,0     3) *
        0,4,0     4) *
        0,5,0     5) *
        0,6,0     6) *
        0,7,0     7) *

Cdrecord release 1.8a30 Copyright (C) 1995-1999 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Using libscg version 'schily-0.1'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'MITSUMI '
Identifikation : 'CR-2801TE       '
Revision       : '1.07'
Device seems to be: Philips CDD-522.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
Drive buf size : 409600 = 400 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data  449 MB        
Total size:     516 MB (51:08.94) = 230171 sectors
Lout start:     516 MB (51:10/71) = 230171 sectors
Current Secsize: -1
ATIP info from disk:
  Indicated writing power: 4
  Is not unrestricted
  Is not erasable
  ATIP start of lead in:  -11570 (97:27/55)
  ATIP start of lead out: 333235 (74:05/10)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 12
Manufacturer: Mitsui Chemicals, Inc.
Blocks total: 333235 Blocks current: 333235 Blocks remaining: 103064
RBlocks total: 343270 RBlocks current: 343270 RBlocks remaining: 113099
Starting to write CD/DVD at speed 2 in write mode for single session.
Last chance to quit, starting real write in 1 seconds.
Waiting for reader process to fill input-buffer ... input-buffer ready.
Starting new track at sector: 0
Track 01:   0 of 449 MB written.cdrecord: Input/output error. write_g1:
scsi sendcmd: retryable error
CDB:  2A 00 00 00 00 10 00 00 10 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 06 00 00 00 00 28 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x28 Qual 0x00 (not ready to ready change, medium may have
changed) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.001s timeout 40s

write track data: error after 32768 bytes
Sense Bytes: 70 00 00 00 00 00 00 06 00 00 00 00 00 00 20 20 20 20
Writing  time:   78.571s
Fixating...
cdrecord: Input/output error. close track/session: scsi sendcmd: retryable
error
CDB:  5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 06 00 00 00 00 10 04 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x10 Qual 0x04 (id crc or ecc error) [No matching qualifier]
Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.001s timeout 480s
Fixating time:    0.004s
cdrecord: fifo had 129 puts and 2 gets.
cdrecord: fifo was 0 times empty and 1 times full, min fill was 99%.