US Robotics USR5410 802.11g Wireless en Wheezy
Hola lista:
La situación es la siguiente:
La tarjeta PCMCIA US Robotics USR5410 funcionaba con Lenny. Esta tarjeta
tiene el chipset de Texas Instruments que funciona con el driver ACX100/111
y el firmware que no es libre "tiacx". La estoy usando en una lapto Fujitsu
Amilo-EL Series
La salida de "lspci" es:
Network controller: Texas Instruments ACX111 54 Mbps Wireless Interface
Al pasar a Squeeze note que ya no se incluía el paquete con el modulo
ACX100/111 compilado, así que seguí para testing. Hasta aquí todo bien.
Despues de poner todo a funcionar en Wheezy solo me quedaba la tarjeta
wireless de forma que me instalé las fuentes del modulo desde el paquete
acx100-source
Usando module-assistant compilé e instalé el modulo acx.
Lo hice así:
m-a prepare acx
m-a build acx
m-a install acx
Acto seguido copié el firmware que usaba bajo Lenny a /lib/firmware.
Inserté la tarjeta arranqué y al iniciar hald obtengo ...
Kernel panic - not sync: stack protector : Kernel stack is corrupted in:
c11db3be
Este mensaje es invariable. Lo obtengo aún sin haber insertado la tarjeta si
escribo "modprobe acx".
Esta es la salida en el /var/log/syslog
Feb 18 13:46:23 amilo kernel: [ 10.360137] acx: this driver is still
EXPERIMENTAL
Feb 18 13:46:23 amilo kernel: [ 10.360142] acx: reading README file and/or
Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further
questions/discussion
Feb 18 13:46:23 amilo kernel: [ 10.360149] acx: compiled to use 32bit I/O
access. I/O timing issues might occur, such as non-working firmware upload.
Report them
Feb 18 13:46:23 amilo kernel: [ 10.360154] acx: running on a little-endian
CPU
Feb 18 13:46:23 amilo kernel: [ 10.360156] acx: PCI/VLYNQ module v0.3.37
initialized, waiting for cards to probe...
Feb 18 13:46:23 amilo kernel: [ 10.360236] acx_pci 0000:02:00.0: enabling
device (0000 -> 0002)
Feb 18 13:46:23 amilo kernel: [ 10.360256] acx_pci 0000:02:00.0: PCI INT A
-> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
Feb 18 13:46:23 amilo kernel: [ 10.360270] acx_pci 0000:02:00.0: setting
latency timer to 64
Feb 18 13:46:23 amilo kernel: [ 10.360370] acx: found ACX111-based
wireless network card at 0000:02:00.0, irq:10, phymem1:0x10020000,
phymem2:0x10000000, me
m1:0xccfbc000, mem1_size:8192, mem2:0xccfc0000, mem2_size:131072
Feb 18 13:46:23 amilo kernel: [ 10.360376] initial debug setting is 0x000A
Feb 18 13:46:23 amilo kernel: [ 10.360404] using IRQ 10
Feb 18 13:46:23 amilo kernel: [ 10.360463] acx: need to load firmware for
acx111 chipset with radio ID 16, please provide via firmware hotplug:
Feb 18 13:46:23 amilo kernel: [ 10.360466] acx: either one file only
(<c>ombined firmware image file, radio-specific) or two files (radio-less
base image file *plus* separate <r>adio-specific extension file)
Feb 18 13:46:23 amilo kernel: [ 10.360473] requesting firmware image
'tiacx111c16'
Feb 18 13:46:23 amilo kernel: [ 10.360479] acx_pci 0000:02:00.0: firmware:
requesting tiacx111c16
Feb 18 13:46:23 amilo kernel: [ 10.363179] Intel ICH 0000:00:02.7: PCI INT
C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
Feb 18 13:46:23 amilo kernel: [ 10.654619] acx_write_fw (main/combined): 0
Feb 18 13:46:23 amilo kernel: [ 10.701621] acx_validate_fw
(main/combined): 0
Feb 18 13:46:23 amilo kernel: [ 11.166708] initializing max packet
templates
Feb 18 13:46:23 amilo kernel: [ 11.248094] dump queue head (from card):
Feb 18 13:46:23 amilo kernel: [ 11.248097] len: 24
Feb 18 13:46:23 amilo kernel: [ 11.248099] tx_memory_block_address: 19060
Feb 18 13:46:23 amilo kernel: [ 11.248101] rx_memory_block_address: 13560
Feb 18 13:46:23 amilo kernel: [ 11.248103] tx1_queue address: 12A94
Feb 18 13:46:23 amilo kernel: [ 11.248104] rx1_queue address: 12754
Feb 18 13:46:23 amilo kernel: [ 11.276124] intel8x0_measure_ac97_clock:
measured 55366 usecs (2663 samples)
Feb 18 13:46:23 amilo kernel: [ 11.276130] intel8x0: clocking to 48000
Feb 18 13:46:23 amilo kernel: [ 11.278041] Intel ICH Modem 0000:00:02.6:
PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
Feb 18 13:46:23 amilo kernel: [ 11.284749] NVS_vendor_offs:01CD
probe_delay:200 eof_memory:1114112
Feb 18 13:46:23 amilo kernel: [ 11.284756] CCAModes:04 Diversity:01
ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01
Feb 18 13:46:23 amilo kernel: [ 11.284760] AntennaID:00 Len:02 Data:01 02
Feb 18 13:46:23 amilo kernel: [ 11.284766] PowerLevelID:01 Len:02
Data:001E 000A
Feb 18 13:46:23 amilo kernel: [ 11.284771] DataRatesID:02 Len:05 Data:02
04 11 22 44
Feb 18 13:46:23 amilo kernel: [ 11.284779] DomainID:03 Len:06 Data:30 20
30 31 32 41
Feb 18 13:46:23 amilo kernel: [ 11.284789] ProductID:04 Len:09 Data:TI
ACX100
Feb 18 13:46:23 amilo kernel: [ 11.284793] ManufacturerID:05 Len:07
Data:TI Test
Feb 18 13:46:23 amilo kernel: [ 11.284798] get_mask 0x00004182, set_mask
0x00000000
Feb 18 13:46:23 amilo kernel: [ 11.296149] don't know how to get
sensitivity for radio type 0x16
Feb 18 13:46:23 amilo kernel: [ 11.296155] got sensitivity value 0
Feb 18 13:46:23 amilo kernel: [ 11.308107] got antenna value 0x4A
Feb 18 13:46:23 amilo kernel: [ 11.320154] got regulatory domain 0x30
Feb 18 13:46:23 amilo kernel: [ 11.320163] get_mask 0x00000000, set_mask
0x00000000 - after update
Feb 18 13:46:23 amilo kernel: [ 11.320170] new ratevector: 82 84 0B 0C 12
16 18 24 2C 30 48 60 6C
Feb 18 13:46:23 amilo kernel: [ 11.320185] setting RXconfig to 2010:0FDD
Feb 18 13:46:23 amilo kernel: [ 11.344177] acx: === chipset TNETW1130,
radio type 0x16 (Radia), form factor 0x01 ((mini-)PCI / CardBus), EEPROM
version 0x05: uploaded firmware 'Rev 1.2.1.34' ===
Feb 18 13:46:23 amilo kernel: [ 11.345353] creating /proc entry
driver/acx_wlan0
Feb 18 13:46:23 amilo kernel: [ 11.345376] creating /proc entry
driver/acx_wlan0_diag
Feb 18 13:46:23 amilo kernel: [ 11.345382] creating /proc entry
driver/acx_wlan0_eeprom
Feb 18 13:46:23 amilo kernel: [ 11.345388] creating /proc entry
driver/acx_wlan0_phy
Feb 18 13:46:23 amilo kernel: [ 11.345412] acx v0.3.37: net device wlan0,
driver compiled against wireless extensions 22 and Linux 2.6.32-5-686
Feb 18 13:46:23 amilo kernel: [ 11.346539] USB module v0.3.37 initialized,
probing for devices...
Feb 18 13:46:23 amilo kernel: [ 11.346618] usbcore: registered new
interface driver acx_usb
Feb 18 13:46:23 amilo kernel: [ 11.514862] udev[268]: renamed network
interface wlan0 to wlan1
Feb 18 13:46:23 amilo kernel: [ 13.079484] Adding 265032k swap on
/dev/sda6. Priority:-1 extents:1 across:265032k
Feb 18 13:46:23 amilo kernel: [ 13.428725] EXT3 FS on sda5, internal
journal
Feb 18 13:46:23 amilo kernel: [ 13.719621] loop: module loaded
Feb 18 13:46:23 amilo kernel: [ 14.348205] fuse init (API version 7.13)
Feb 18 13:46:23 amilo acpid: starting up with netlink and the input layer
Feb 18 13:46:23 amilo acpid: 1 rule loaded
Feb 18 13:46:23 amilo acpid: waiting for events: event logging is off
Feb 18 13:46:24 amilo kernel: [ 18.808912] eth0: Media Link On 100mbps
full-duplex
La salida del comando ls /lib/firmware es:
root@amilo:~# clear && ls -lha /lib/firmware/
total 404K
drwxr-xr-x 2 root root 4.0K Feb 18 13:27 .
drwxr-xr-x 13 root root 12K Feb 17 14:55 ..
-rw-r--r-- 1 root root 42K Sep 24 2004 acx100_usb.bin
-rw-r--r-- 1 root root 936 Apr 26 2004 radio0d.bin
-rw-r--r-- 1 root root 964 Apr 26 2004 radio11.bin
-rw-r--r-- 1 root root 912 Apr 26 2004 radio15.bin
-rw-r--r-- 1 root root 8.0K Jan 3 20:40 rt2561.bin
-rw-r--r-- 1 root root 8.0K Jan 3 20:40 rt2561s.bin
-rw-r--r-- 1 root root 8.0K Jan 3 20:40 rt2661.bin
-rw-r--r-- 1 root root 8.0K Jan 3 20:40 rt2860.bin
-rw-r--r-- 1 root root 4.0K Jan 3 20:40 rt2870.bin
-rw-r--r-- 1 root root 4.0K Jan 3 20:40 rt3070.bin
-rw-r--r-- 1 root root 4.0K Jan 3 20:40 rt3071.bin
-rw-r--r-- 1 root root 8.0K Jan 3 20:40 rt3090.bin
-rw-r--r-- 1 root root 2.0K Jan 3 20:40 rt73.bin
-rw-r--r-- 1 root root 75K Dec 18 22:54 tiacx111
-rw-r--r-- 1 root root 82K Dec 18 22:54 tiacx111c16
-rw-r--r-- 1 root root 83K Dec 18 22:55 tiacx111c17
-rw-r--r-- 1 root root 7.1K Dec 18 22:55 tiacx111r16
-rw-r--r-- 1 root root 8.8K Dec 18 22:55 tiacx111r17
Los archivos rt73 se deben a que en el lugar de la tarjeta US Robotics estoy
usando una interfaz wireless usb DLink DWA-110 que con los drivers de RALink
funciona, pero es incomodo de usar.
Creo no haber omitido información necesaria para que me puedan señalar que
hice mal, pues todo fue realizado completamente a ciegas.
Perdonen la exagerada longitud del mensaje y si además he violado alguna
norma de la lista, señálenlo y me corregiré.
Gracias por su tiempo a todos.
Reply to: