Conexion ADSL: Porque todo es tan complicado? - Mas cerca de la Solucion
Hola, sigo con mi problema pero mas cerca de la solucion. Jugueteando un poco logre configurar ppp y durante unos segundos logre navegar(entre a la pag de google hice una busqueda), ero luego se callo y no pude hacer mas nada. Antes de conectarme ejecute los siguientes comandos
* pon
* plog
* ifconfig
y esto es lo que me salio:
Debian:/etc/network# pon
Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
Debian:/etc/network# plog
Dec 20 19:00:15 Debian pppd[3922]: Couldn't increase MRU to 1500
Dec 20 19:00:15 Debian pppd[3922]: Couldn't increase MRU to 1500
Dec 20 19:00:15 Debian pppd[3922]: PAP authentication succeeded
Dec 20 19:00:15 Debian pppd[3922]: peer from calling number 00:90:1A:41:1B:14 authorized
Dec 20 19:00:16 Debian pppd[3922]: not replacing default route to eth1 [10.0.0.2]
Dec 20 19:00:16 Debian pppd[3922]: Cannot determine ethernet address for proxy ARP
Dec 20 19:00:16 Debian pppd[3922]: local IP address 200.127.140.169
Dec 20 19:00:16 Debian pppd[3922]: remote IP address 200.51.241.227
Dec 20 19:00:16 Debian pppd[3922]: primary DNS address 200.42.97.110
Dec 20 19:00:16 Debian pppd[3922]: secondary DNS address 200.42.0.110
Debian:/etc/network# ifconfig
eth0 Link encap:Ethernet HWaddr 00:E0:4C:C0:02:8A
inet addr:172.16.100.1 Bcast:172.16.255.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:4cff:fec0:28a/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:3512 (3.4 KiB)
Interrupt:185 Base address:0xd400
eth1 Link encap:Ethernet HWaddr 00:0F:EA:D1:A1:50
inet addr:10.0.0.1 Bcast:255.255.255.255 Mask:255.255.255.252
inet6 addr: fe80::20f:eaff:fed1:a150/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:733 errors:0 dropped:0 overruns:0 frame:0
TX packets:522 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:81463 (79.5 KiB) TX bytes:45929 (44.8 KiB)
Interrupt:217 Base address:0xec00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:800 (800.0 b) TX bytes:800 (800.0 b)
ppp0 Link encap:Point-to-Point Protocol
inet addr:200.127.140.169 P-t-P:200.51.241.227 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:808 (808.0 b) TX bytes:54 (54.0 b)
Luego de esto hice:
route add default ppp0
y ahi me andubo. Cuando dejo de andar, detuve la red (networking stop; networking start) y volvi a ejecutar todo eso, pero la ultima interfaz(ppp0) no aparece, solo me aparecio una o dos veces. Al ejecutar nuevamente:
route add default ppp0
No estiste el dispositivo...
Sugerencias?
Reply to: