Re: eth0 y eth1 colision
Yo creo que es problema de rutas. Prueba a añadirle una ruta statica
para que vaya a la LAN.
route add 192.168.1.2 192.168.1.1 (Mirate como se hace que este seguro
que falla)
Suerte
On 8/19/05, fernando villarroel <bbddlinux@yahoo.es> wrote:
> Te pego las salidas de netstat, ifconfig y otros
>
> woody:/home/fvillarroel# netstat -nr
> Kernel IP routing table
> Destination Gateway Genmask Flags
> MSS Window irtt Iface
> 10.52.xx.x 0.0.0.0 255.255.255.255 UH
> 40 0 0 ppp0
> 192.168.2.0 0.0.0.0 255.255.255.0 U
> 40 0 0 vpn
> 192.168.1.0 0.0.0.0 255.255.255.0 U
> 40 0 0 eth1
> 192.168.1.0 0.0.0.0 255.255.255.0 U
> 40 0 0 vpn
> 0.0.0.0 10.52.xx.x 0.0.0.0 UG
> 40 0 0 ppp0
> woody:/home/fvillarroel#
>
> woody:/home/fvillarroel# ifconfig
> eth0 Link encap:Ethernet HWaddr
> 00:50:BA:4F:6D:B1
> UP BROADCAST RUNNING MULTICAST MTU:1500
> Metric:1
> RX packets:544 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:320 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0 txqueuelen:100
> RX bytes:61105 (59.6 KiB) TX bytes:42852
> (41.8 KiB)
> Interrupt:9 Base address:0xa100
>
> eth1 Link encap:Ethernet HWaddr
> 00:20:AF:71:66:49
> inet addr:192.168.1.1 Bcast:192.168.1.255
> Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500
> Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:18 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0 txqueuelen:100
> RX bytes:0 (0.0 b) TX bytes:756 (756.0 b)
> Interrupt:10 Base address:0x300
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:32 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:32 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0 txqueuelen:0
> RX bytes:3276 (3.1 KiB) TX bytes:3276 (3.1
> KiB)
>
> ppp0 Link encap:Point-to-Point Protocol
> inet addr:200.111.xx.xx P-t-P:10.52.xx.x
> Mask:255.255.255.255
> UP POINTOPOINT RUNNING NOARP MULTICAST
> MTU:1492 Metric:1
> RX packets:452 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:221 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0 txqueuelen:3
> RX bytes:45547 (44.4 KiB) TX bytes:31957
> (31.2 KiB)
>
> vpn Link encap:Point-to-Point Protocol
> inet addr:192.168.1.1 P-t-P:192.168.1.1
> Mask:255.255.255.0
> UP POINTOPOINT RUNNING NOARP MULTICAST
> MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0
> frame:0
> TX packets:0 errors:0 dropped:0 overruns:0
> carrier:0
> collisions:0 txqueuelen:10
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>
>
> woody:/home/fvillarroel# route
> Kernel IP routing table
> Destination Gateway Genmask Flags
> Metric Ref Use Iface
> 10.52.xx.x * 255.255.255.255 UH
> 0 0 0 ppp0
> 192.168.2.0 * 255.255.255.0 U
> 0 0 0 vpn
> localnet * 255.255.255.0 U
> 0 0 0 eth1
> localnet * 255.255.255.0 U
> 0 0 0 vpn
> default 10.52.xx.x 0.0.0.0 UG
> 0 0 0 ppp0
>
> woody:/var/log# lspci
> 00:00.0 Host bridge: Intel Corp. 440FX - 82441FX PMC
> [Natoma] (rev 02)
> 00:0d.0 PCI bridge: IBM IBM27-82351 (rev 01)
> 00:12.0 SCSI storage controller: LSI Logic / Symbios
> Logic (formerly NCR) 53c875 (rev 03)
> 00:14.0 EISA bridge: Compaq Computer Corporation PCI
> to EISA Bridge (rev 07)
> 01:06.0 VGA compatible controller: Cirrus Logic GD
> 5430/40 [Alpine] (rev 22)
> 01:07.0 Network controller: Compaq Computer
> Corporation ProLiant Integrated Netelligent 10/100
> (rev 10)
> 01:09.0 SCSI storage controller: LSI Logic / Symbios
> Logic (formerly NCR) 53c875 (rev 03)
> 01:0b.0 Ethernet controller: D-Link System Inc RTL8139
> Ethernet (rev 10)
> woody:/var/log#
>
>
> Te pego lo que me tira dmesg al iniciar el servidor:
>
> TLAN: eth2 irq=10, io=7800, Compaq Netelligent
> Integrated 10/100 TX UTP, Rev. 16
> TLAN: 1 device installed, PCI: 1 EISA: 0
> eth0: Setting 100mbps full-duplex based on
> auto-negotiated partner ability 41e1.
> eth1: Setting Rx mode to 1 addresses.
>
>
> Como ves tengo una vpn y fuinciona perfecto, con
> equipos que estan remotamente.
> Ademas eth0 esta sin dreccion ip ya que por ahy se
> levanta la interfaz ppp0 (ADSL)
>
>
> TLAN corresponde a una tarjeta integrada que trae el
> servidor, pero que esa si que esta mala fisicamente en
> el switch de coneccion, no se puede usar
>
> Ya he probado varias alternativas y nada.
>
> Lo otro es que no me deja instalar el modulo via-rhine
> que correspionde al modulo que usan las tarjetas de
> d-link, pero no me deja. De que otra forma le puedo
> cargar el modulo de las tarjetas d-link, ademas de
> modconf
>
>
> Mi teoria es problema en la tarjeta aunque he probado
> cambiandolas, de hecho tengo un set de 4 tarjetas
> d-link, 3com y no creo que esten todas malas, lo otro
> que pienso es que el hub este presentando problemas.
>
> Bueno ojala me puedas ayudar
>
> Fernando Villarroel
>
> --- DK <ionidk@gmail.com> escribió:
>
> > El problema no lo veo en el eth0 mas bien diria que
> > esta en el eth1 o
> > sino en la tabla de rutas. Tambien podria darse el
> > caso de que la
> > propia tarjeta estuviera mal. Has probado a
> > configurar solo la eth0 o
> > la eth1? Quizas la eth1 este mal.
> > Un ping a la IP de la eth1 responde?
> > No tendras iptables no? Si pones iptables -L existe
> > algun drop que
> > pueda ser el causante de los problemas?
> >
> > Un saludo
> >
> >
> > On 8/19/05, Luis Vega <fodsite@gmail.com> wrote:
> > > eth0 es con ip 0.0.0.0 ?
> > > a que te refieres con eso?.
> > >
> > > Si te conectas con eth0, me imagino que tienes una
> > conexion adsl con pppoe.
> > >
> > > A mi parece la interfaz eth0 no deberia llevar
> > ninguna configuracion, ya que
> > > se le asigna un IP cuando se establece la conexion
> > con internet.
> > >
> > > --
> > > Luis Vega M.
> > > Linux Registered User #356394
> > > http://fodsite.webcindario.com
> >
>
>
>
>
>
>
> ______________________________________________
> Renovamos el Correo Yahoo!
> 1GB de capacidad, nuevos servicios y más seguridad
> http://correo.yahoo.es
>
Reply to: