placa base con chip nforce
Hola a todos
En un ordenador con 4 discos duros dos IDE y 2 SATA (los SATA en RAID 0)
al hacer dmesg me sale lo siguiente:
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling
workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA,
hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA,
hdd:DMA
hda: MAXTOR 6L080J4, ATA DISK drive
hdb: Maxtor 6Y120L0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY CD-RW CRX175A1, ATAPI CD/DVD-ROM drive
hdd: PIONEER DVD-ROM DVD-115, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
SiI3112 Serial ATA: IDE controller at PCI slot 0000:01:0b.0
SiI3112 Serial ATA: chipset revision 2
SiI3112 Serial ATA: 100% native mode on irq 18
ide2: MMIO-DMA , BIOS settings: hde:pio, hdf:pio
ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
hde: Maxtor 6Y160M0, ATA DISK drive
ide2 at 0xe083c080-0xe083c087,0xe083c08a on irq 18
hdg: Maxtor 6Y160M0, ATA DISK drive
ide3 at 0xe083c0c0-0xe083c0c7,0xe083c0ca on irq 18
hda: max request size: 128KiB
hda: 156355584 sectors (80054 MB) w/1819KiB Cache,
CHS=65535/16/63, UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 >
hdb: max request size: 128KiB
hdb: 240121728 sectors (122942 MB) w/2048KiB Cache,
CHS=65535/16/63, UDMA(133)
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3 p4 < p5 p6 >
hde: max request size: 64KiB
hde: 320173056 sectors (163928 MB) w/7936KiB Cache,
CHS=19929/255/63
/dev/ide/host2/bus0/target0/lun0: p1 < >
hdg: max request size: 64KiB
hdg: 320173056 sectors (163928 MB) w/7936KiB Cache,
CHS=19929/255/63
/dev/ide/host2/bus1/target0/lun0: unknown partition table
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1052216k swap on /dev/hda9. Priority:-1 extents:1
EXT3 FS on hda8, internal journal
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/core/usb.c: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard
driver
Linux video capture interface: v1.00
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <bcollins@debian.org>
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]
MMIO=[e2084000-e20847ff] Max Packet=[2048]
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[e1008000-e10087ff] Max Packet=[2048]
drivers/usb/core/usb.c: registered new driver hiddev
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
NTFS driver 2.1.6 [Flags: R/O MODULE].
ohci1394: fw-host0: SelfID received outside of bus reset
sequence
mice: PS/2 mouse device common for all mice
input: GenPS/2 Genius Wheel Mouse on isa0060/serio1
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000077bcf0]
ip1394: $Rev: 1175 $ Ben Collins <bcollins@debian.org>
ip1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
ieee1394: Host added: ID:BUS[1-00:1023] GUID[00023c003002c9ae]
bttv: driver version 0.9.12 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt848 (rev 18) at 0000:01:09.0, irq: 17, latency: 32,
mmio: 0xdc000000
bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ff07ff [init]
bttv: readee error
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... <6>ts: Compaq
touchscreen protocol output
not found
bttv0: registered device video0
bttv0: registered device vbi0
SCSI subsystem initialized
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI)
Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 20, pci mem e0b20000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller
(#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 22, pci mem e0b24000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus
number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
devfs_mk_dev: could not append to parent for sound/audio
Creative EMU10K1 PCI Audio Driver, version 0.20a, 04:05:49 Apr
28 2004
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
ide-scsi is deprecated for cd burning! Use ide-cd and give
dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SONY Model: CD-RW CRX175A1 Rev: 5YS2
Type: CD-ROM ANSI SCSI revision:
02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: DVD-ROM DVD-115 Rev: 1.12
Type: CD-ROM ANSI SCSI revision:
02
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised:
dm@uk.sistina.com
NTFS volume version 3.0.
NTFS volume version 3.0.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.5-1-k7
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xd8000000
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 21, pci mem e0c1c000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus
number 3
PCI: cache line size of 64 is not supported by device
0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver
2003-Dec-29
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
forcedeth.c: Reverse Engineered nForce ethernet driver. Version
0.25.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth2: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 84846 usecs
intel8x0: clocking to 48000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
gameport: pci0000:01:07.1 speed 890 kHz
libata version 1.02 loaded.
lp0: using parport0 (interrupt-driven).
Los discos SATA son hde y hdg pero
¿como puedo montarlos como uno solo en RAID 0?
muchas gracias
Reply to: