Re: disco-duro-chungo
Éste poblema mismo me ocurria a mi en un servidor que monté. Tenia dos
discos de 60 en un ATARAID tipo 1 y éste error me lo daba siempre al
arrancar cuando tenia los discos metidos en cajetines extraibles.
Conectándolos directamente a la manguera no daba ese error.
El servidor corria Potato (ahora Woody) con un kernel 2.4.14 y la
controladora RAID és una Konwel con chip hpt570 (pero ya te digo que no
era fallo de la controladora si no de los cajetines). Ahora el servidor
está funcionando con los cajetines conectados a pleno rendimiento y no
da ningún problema.
El lun, 14-10-2002 a las 22:54, Manwe Sulimo escribió:
> He comprado un disco duro. Lo he particionado con la cd de la woody, he instalado el sistema base y he actualizado a testing. Mi sorpresa cuando al copiar el directorio home de otro disco me daba una tasa de 100MB/MINUTO!! Luego al usar mi sistema wme di cuenta de que las X y las aplicaciones son inestables. El error que me suelen dar los programas es el siguiente:
>
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hdb: DMA disabled
>
> este error tambien me lo da en el arranque del kernel que he compilado aunque no el kernel que me instaló la woody. Aqui pongo los dos mensajes del arranque de los dos kernels. Ayuda por favor.
>
> Linux version 2.4.18monolith (root@taniquetil) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 jue oct 10 03:24:22 CEST 2002
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
> BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
> BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> On node 0 totalpages: 131056
> zone(0): 4096 pages.
> zone(1): 126960 pages.
> zone(2): 0 pages.
> Kernel command line: BOOT_IMAGE=Linux ro root=305
> Initializing CPU#0
> Detected 1541.235 MHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 3073.63 BogoMIPS
> Memory: 513436k/524224k available (1350k kernel code, 10404k reserved, 410k data, 192k init, 0k highmem)
> Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
> Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
> Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
> CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After vendor init, caps: 0383fbff c1c3fbff 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
> CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
> CPU: AMD Athlon(tm) XP 1800+ stepping 02
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> PCI: PCI BIOS revision 2.10 entry at 0xfb5f0, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Unknown bridge resource 0: assuming transparent
> PCI: Using IRQ router VIA [1106/0686] at 00:07.0
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> Starting kswapd
> Journalled Block Device driver loaded
> NTFS driver v1.1.22 [Flags: R/O]
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> block: 128 slots per queue, batch=32
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
> ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
> hda: ST340016A, ATA DISK drive
> hdb: HL-DT-ST CD-ROM GCR-8520B, ATAPI CD/DVD-ROM drive
> hdc: ST38420A, ATA DISK drive
> hdd: MATSHITA CD-R CW-7582, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
> hdc: 16841664 sectors (8623 MB) w/512KiB Cache, CHS=16708/16/63, UDMA(33)
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> hdc: [PTBL] [1048/255/63] hdc1 hdc2 hdc3 hdc4
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> PPP generic driver version 2.4.1
> PPP Deflate Compression module registered
> PPP BSD Compression module registered
> Linux agpgart interface v0.99 (c) Jeff Hartmann
> agpgart: Maximum main memory to use for agp memory: 439M
> agpgart: unsupported bridge
> agpgart: no supported devices found.
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> Vendor: HL-DT-ST Model: CD-ROM GCR-8520B Rev: 1.00
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: MATSHITA Model: CD-R CW-7582 Rev: 1.05
> Type: CD-ROM ANSI SCSI revision: 02
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
> sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.12
> sr1: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
> Via 686a audio driver 1.9.1
> PCI: Found IRQ 10 for device 00:07.5
> ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
> via82cxxx: Codec rate locked at 48Khz
> via82cxxx: board #1 at 0xE000, IRQ 10
> es1371: version v0.30 time 03:25:22 Oct 10 2002
> usb.c: registered new driver hub
> uhci.c: USB Universal Host Controller Interface driver v1.1
> PCI: Found IRQ 12 for device 00:07.2
> PCI: Sharing IRQ 12 with 00:07.3
> uhci.c: USB UHCI at I/O 0xd800, IRQ 12
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 2 ports detected
> PCI: Found IRQ 12 for device 00:07.3
> PCI: Sharing IRQ 12 with 00:07.2
> uhci.c: USB UHCI at I/O 0xdc00, IRQ 12
> usb.c: new USB bus registered, assigned bus number 2
> hub.c: USB hub found
> hub.c: 2 ports detected
> Initializing USB Mass Storage driver...
> usb.c: registered new driver usb-storage
> USB Mass Storage support registered.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 4096 buckets, 32Kbytes
> TCP: Hash tables configured (established 32768 bind 32768)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 192k freed
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hdb: DMA disabled
> ide0: reset: success
> Adding Swap: 996020k swap-space (priority -1)
> nvidia: loading NVIDIA Linux x86 NVdriver Kernel Module 1.0-3123 Tue Aug 27 15:56:48 PDT 2002
> NVRM: AGPGART: unable to retrieve symbol table
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide1(22,4), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
>
>
>
>
>
> Linux version 2.2.20-idepci (herbert@gondolin) (gcc version 2.7.2.3) #1 Sat Apr 20 12:45:19 EST 2002
> BIOS-provided physical RAM map:
> BIOS-e820: 000a0000 @ 00000000 (usable)
> BIOS-e820: 1fef0000 @ 00100000 (usable)
> Detected 1541261 kHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 3073.63 BogoMIPS
> Memory: 517148k/524224k available (1164k kernel code, 408k reserved, 5432k data, 72k init)
> Dentry hash table entries: 65536 (order 7, 512k)
> Buffer cache hash table entries: 524288 (order 9, 2048k)
> Page cache hash table entries: 131072 (order 7, 512k)
> CPU: L1 I Cache: 64K L1 D Cache: 64K
> CPU: L2 Cache: 256K
> CPU: AMD Athlon(tm) XP 1800+ stepping 02
> Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
> Checking 'hlt' instruction... OK.
> Checking for popad bug... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
> PCI: PCI BIOS revision 2.10 entry at 0xfb5f0
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Enabling I/O for device 00:00
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> TCP: Hash tables configured (ehash 524288 bhash 65536)
> Starting kswapd v 1.5
> vga16fb: initializing
> vga16fb: mapped to 0xc00a0000
> Console: switching to colour frame buffer device 80x30
> fb0: VGA16 VGA frame buffer device
> Detected PS/2 Mouse Port.
> Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> pty: 256 Unix98 ptys configured
> RAM disk driver initialized: 16 RAM disks of 4096K size
> loop: registered device at major 7
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
> hda: ST340016A, ATA DISK drive
> hdb: HL-DT-ST CD-ROM GCR-8520B, ATAPI CDROM drive
> hdc: ST38420A, ATA DISK drive
> hdd: MATSHITA CD-R CW-7582, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: ST340016A, 38166MB w/2048kB Cache, CHS=4865/255/63
> hdc: ST38420A, 8223MB w/512kB Cache, CHS=16708/16/63
> hdb: ATAPI 52X CD-ROM drive, 128kB Cache
> Uniform CD-ROM driver Revision: 3.11
> hdd: ATAPI 8X CD-ROM CD-R drive, 1024kB Cache
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> 3c59x.c 18Feb01 Donald Becker and others http://www.scyld.com/network/vortex.html
> pcnet32.c: PCI bios is present, checking for devices...
> via-rhine.c:v1.08b-LK1.0.1 12/14/2000 Written by Donald Becker
> http://www.scyld.com/network/via-rhine.html
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> hdc: [PTBL] [1048/255/63] hdc1 hdc2 hdc3 hdc4
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
> apm: disabled on user request.
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 72k freed
> Adding Swap: 996020k swap-space (priority -1)
> NTFS version 000607
> CSLIP: code copyright 1989 Regents of the University of California
> SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256).
> SLIP linefill/keepalive option.
>
>
> --
> To UNSUBSCRIBE, email to debian-user-spanish-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
>
--
Reply to: