Re: Configurar Tarjeta NE2000 ISA
Gracias Ernesto, parece que la cosa progresa, pero todavía no está
lista. Creo que he hecho lo que me comentas. He intentado activar la
tarjeta con ifconfig eth1, pero me responde, dispositivo
desconocido. Adjunto los ficheros isapnp.conf y modules.conf. A ver si
veis el error, o me comentais cual es el siguiente paso. Un saludo y
gracias.
Isaac.
On Thu, 7 Feb 2002, Ernesto wrote:
>
> mmmm...
> yo tenia una tarjeta compatible con ne2000 y iba muy
> bien.
> en
> isapnp
> tienes que descomentar (quitar el #) a donde esta la
> configuracion del IRQ=10 y io=0x220
> y quitar tambien el # de (ACT Y) para que funcione
>
> y en el Conf.modules lo tines
> que poner algo asi
> alias eth0 ne
> options ne io=0x220 irq=10
>
> y con eso debe funcionar
>
> si no mandanos tu isapnp.conf y modules.con y te dijo
> donde estas mal..
# $Id: pnpdump.c,v 1.21 1999/12/09 22:28:33 fox Exp $
# Release isapnptools-1.21 (library isapnptools-1.21)
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
# = 10
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
# (for library: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR)
#
# Trying port address 0273
# Board 1 has serial identifier 58 08 35 65 18 19 80 63 5e
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 58 08 35 65 18 19 80 63 5e)
# Vendor Id WSC8019, Serial Number 137717016, checksum 0x58.
# Version 1.0, Vendor version 1.0
# ANSI string -->Plug & Play Ethernet Card<--
#
# Logical device id RTL8019
# Device supports I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE WSC8019/137717016 (LD 0
# Compatible device id PNP80d6
# Logical device decodes 10 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0380
# IO base alignment 32 bytes
# Number of IO addresses required: 32
(IO 0 (SIZE 32) (BASE 0x220) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11, 12 or 15.
# High true, edge sensitive interrupt
(INT 0 (IRQ 10 (MODE +E)))
(NAME "WSC8019/137717016[0]{Plug & Play Ethernet Card}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
### This file is automatically generated by update-modules
#
# Please do not edit this file directly. If you want to change or add
# anything please take a look at the files in /etc/modutils and read
# the manpage for update-modules.
#
### update-modules: start processing /etc/modutils/0keep
# DO NOT MODIFY THIS FILE!
# This file is not marked as conffile to make sure if you upgrade modutils
# it will be restored in case some modifications have been made.
#
# The keep command is necessary to prevent insmod and friends from ignoring
# the builtin defaults of a path-statement is encountered. Until all other
# packages use the new `add path'-statement this keep-statement is essential
# to keep your system working
keep
### update-modules: end processing /etc/modutils/0keep
### update-modules: start processing /etc/modutils/aliases
# Aliases to tell insmod/modprobe which modules to use
#@@@# Alias para la tarjeta ethernet ISA NE2000 von Novell/Anthem.
alias eth0 ne
options ne io=0x220 irq=10
#@@@#
# Uncomment the network protocols you don't want loaded:
# alias net-pf-1 off # Unix
# alias net-pf-2 off # IPv4
# alias net-pf-3 off # Amateur Radio AX.25
# alias net-pf-4 off # IPX
# alias net-pf-5 off # DDP / appletalk
# alias net-pf-6 off # Amateur Radio NET/ROM
# alias net-pf-9 off # X.25
# alias net-pf-10 off # IPv6
# alias net-pf-11 off # ROSE / Amateur Radio X.25 PLP
# alias net-pf-19 off # Acorn Econet
alias char-major-10-130 softdog
alias char-major-10-175 agpgart
alias char-major-81 bttv
alias char-major-108 ppp_generic
alias /dev/ppp ppp_generic
alias tty-ldisc-3 ppp_async
alias tty-ldisc-14 ppp_synctty
alias ppp-compress-21 bsd_comp
alias ppp-compress-24 ppp_deflate
alias ppp-compress-26 ppp_deflate
# Crypto modules (see http://www.kerneli.org/)
alias loop-xfer-gen-0 loop_gen
alias loop-xfer-3 loop_fish2
alias loop-xfer-gen-10 loop_gen
alias cipher-2 des
alias cipher-3 fish2
alias cipher-4 blowfish
alias cipher-6 idea
alias cipher-7 serp6f
alias cipher-8 mars6
alias cipher-11 rc62
alias cipher-15 dfc2
alias cipher-16 rijndael
alias cipher-17 rc5
### update-modules: end processing /etc/modutils/aliases
### update-modules: start processing /etc/modutils/paths
# This file contains a list of paths that modprobe should scan,
# beside the once that are compiled into the modutils tools
# themselves.
# This used to be quite a list, but upstream merged some Debian patches
# so we currently don't need to do anything here
### update-modules: end processing /etc/modutils/paths
### update-modules: start processing /etc/modutils/setserial
#
# This is what I wanted to do, but logger is in /usr/bin, which isn't loaded
# when the module is first loaded into the kernel at boot time!
#
#post-install serial /etc/init.d/setserial start | logger -p daemon.info -t "setserial-module reload"
#pre-remove serial /etc/init.d/setserial stop | logger -p daemon.info -t "setserial-module uload"
post-install serial /etc/init.d/setserial modload > /dev/null 2> /dev/null
pre-remove serial /etc/init.d/setserial modsave > /dev/null 2> /dev/null
### update-modules: end processing /etc/modutils/setserial
### update-modules: start processing /etc/modutils/arch/i386
alias parport_lowlevel parport_pc
alias char-major-10-144 nvram
alias binfmt-0064 binfmt_aout
alias char-major-10-135 rtc
### update-modules: end processing /etc/modutils/arch/i386
Reply to: