Arranque dual LILO (linux + windows 98)
Hola:
No soy capaz de poner a funcionar el LILO con windows 98. Tengo dos
discos duros hdc de 10 Gb con Potato y el hda de 2.4Gb, donde contra mi
voluntad he tenido que instalar el windows ese. Instalo el LILO y no
logra arrancar, me da el error 40, osea
L 40 40 40 40 ...
He mirado en la documentación del LILO y para este error en concreto no
dice gran cosa ("Seek failure". This might be a media problem. Try
booting again) lo intento y nada. También he probado a especificar la
geometría del disco...más de lo mismo.
¿Dónde puedo encontrar más información al respecto?¿Alguien ha tenido
algún problema similar?
Muchas gracias,
Quique
Mi lilo.conf es el siguiente:
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Disk geometry.
#
#disk = /dev/hda
# bios = 0x80
# sectors = 63
# heads = 64
# cylinders = 1023
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
prompt
timeout=50
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
#compact
#linear
# Specifies the VGA text mode at boot time. (normal, extended, ask,
<mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hdc1
# Installs the specified file as the new boot sector
#
install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
# prompt
# single-key
# delay=100
# timeout=100
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=DebianPotato
image=/vmlinuz
label=DebianPotato
read-only
# restricted
alias=1
#image=/mnt/hdc2/boot/vmlinuz-2.0.35-2
# label=RedHat5.1
# root=/dev/hdc2
# read-only
# alias=2
#image=/boot/vmlinuz-2.0.35-2
# label=DebianOld
# read-only
# alias=2
#image=/vmlinuz.old
# label=LinuxOLD
# read-only
# optional
# restricted
# alias=3
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
other=/dev/hda1
label=Windows
# restricted
alias=2
Reply to: