IBM Aptiva (Re: XF86Config)
Hola francisco,
ya he conseguido hacer *funcionar el XFree* (te paso los archivos
XF86Config y X.err) me funciona en *todas las resoluciones* (cuatro,
creo, no recuerdo estoy escribiendo de memória), peerooo,
peeeerroooooroooo!!!!, esto me va a costar de explicar pués es muy
difícil sin que veas mi pantalla, aunque todas las resoluciones me
funcionen (aún no he probado más de 8bpp) veo la pantalla al completo
del monitor, cosa buena, pero la veo más pequeña de lo que tendría.
Me explico, si puedo, es como si el XFree funcionase a una resolución
diferente a la pantalla (ya sé que suena raro pero es que no sé como
decirlo). Dicho de otra forma una cosa que ha 640x480 (en un monitor de
15") ocupa unos 5 cm de altura, por decir algo, a mi en 640x480, con
fvwm95, me ocupa 2,5cm.
Haber si lo has entendido:
- El la pantalla la tengo centrada correctamente, no me sale ovalada,
en fin, es perfecta, a 8bpp, no he probado a más.
- El problema es que me salen las cosas en pantalla más pequeñas de lo
que deben.
En fin, esto es todo, espero que te sirva de algo pués son todos mis
avances. Cuando puedas, explicame tus avances a ver que tal te ha ido
(espero que mejor que a mi :)).
Un cordial saludo,
J. Parera
P.D.
Perdona por ese rollo tan mal explicado pero es que no tenia ni remota
idea de como expresar esta situación. Espero haberme hecho entender.
XFree86 Version 3.3 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: Jun 2 1997
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.21 i486 [ELF]
Configured drivers:
SVGA: server for SVGA graphics adaptors (Patchlevel 0):
NV1, STG2000, ET4000, ET4000W32, ET4000W32i, ET4000W32i_rev_b,
ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a, ET4000W32p_rev_b,
ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, et3000, pvga1, wd90c00,
wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, ati, sis86c201,
sis86c202, sis86c205, tvga8200lx, tvga8800cs, tvga8900b, tvga8900c,
tvga8900cl, tvga8900d, tvga9000, tvga9000i, tvga9100b, tvga9200cxr,
tgui9320lcd, tgui9400cxi, tgui9420, tgui9420dgi, tgui9430dgi,
tgui9440agi, tgui96xx, cyber938x, clgd5420, clgd5422, clgd5424,
clgd5426, clgd5428, clgd5429, clgd5430, clgd5434, clgd5436, clgd5446,
clgd5480, clgd5462, clgd5464, clgd5465, clgd6205, clgd6215, clgd6225,
clgd6235, clgd7541, clgd7542, clgd7543, clgd7548, clgd7555, ncr77c22,
ncr77c22e, cpq_avga, mga2064w, mga1064sg, oti067, oti077, oti087,
oti037c, al2101, ali2228, ali2301, ali2302, ali2308, ali2401, cl6410,
cl6412, cl6420, cl6440, video7, ct65520, ct65525, ct65530, ct65535,
ct65540, ct65545, ct65546, ct65548, ct65550, ct65554, ct64200,
ct64300, ark1000vl, ark1000pv, ark2000pv, ark2000mt, mx, realtek,
AP6422, AT24, s3_virge, generic
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: disabled
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/mouse, baudrate: 1200,
3 button emulation (timeout: 50ms)
(**) SVGA: Graphics device ID: "Generic SVGA"
(**) SVGA: Monitor ID: "My Monitor"
(--) SVGA: Mode "320x200" needs vert refresh rate of 139.87 Hz. Deleted.
(--) SVGA: Mode "320x240" needs vert refresh rate of 120.11 Hz. Deleted.
(**) SVGA: Memory Base Address: 20000000
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(--) SVGA: PCI: SiS SG86C205 rev 211, Memory @ 0x20000000, 0x20400000, I/O @ 0x1200
(--) SVGA: using programmable clocks.
(**) SVGA: chipset: sis86c205
(--) SVGA: videoram: 2048k
(**) SVGA: Option "noaccel"
(**) SVGA: Option "no_bitblt"
(**) SVGA: Option "no_imageblt"
(**) SVGA: Using 8 bpp, Depth 8, Color weight: 666
(--) SVGA: Maximum allowed dot-clock: 135.000 MHz
(**) SVGA: Mode "640x480": mode clock = 25.175
(**) SVGA: Mode "800x600": mode clock = 50.000
(**) SVGA: Mode "1024x768": mode clock = 65.000
(--) SVGA: There is no mode definition named "320x240"
(--) SVGA: Removing mode "320x240" from list of valid modes.
(**) SVGA: Mode "640x400": mode clock = 25.175
(--) SVGA: Virtual resolution set to 1024x768
(--) SVGA: Generic SpeedUps selected (Flags=0x30)
(**) SVGA: base address is set at 0x20000000.
(--) SVGA: Using Linear Frame Buffer at 0x020000000, Size 2MB
(**) SVGA: SIS: Bit Block Transfert disabled
(**) SVGA: Using hardware cursor
(**) SVGA: SIS: Not using mono expand system-to-video BitBLT.
# File generated by xf86config.
#
# Copyright (c) 1995 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# For OSs that support Dynamically loaded modules, ModulePath can be
# used to set a search path for the modules. This is currently supported
# for Linux ELF, FreeBSD 2.x and NetBSD 1.x. The default path is shown
# here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which dynamically loadable modules to load. Dynamically loadable
# modules are currently supported only for Linux ELF, FreeBSD 2.x
# and NetBSD 1.x. Currently, dynamically loadable modules are used
# only for some extended input (XInput) device drivers.
# **********************************************************************
#
# Section "Module"
#
# This loads the module for the Joystick driver
#
# Load "xf86Jstk.so"
#
# EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# NoTrapSignals
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# DontZap
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# DontZoom
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# DisableVidModeExtension
# Uncomment this to enable the use of a non-local xvidtune client.
# AllowNonLocalXvidtune
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# DisableModInDev
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# AllowNonLocalModInDev
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Keyboard section
# **********************************************************************
Section "Keyboard"
Protocol "Standard"
# when using XQUEUE, comment out the above line, and uncomment the
# following line
# Protocol "Xqueue"
AutoRepeat 500 5
# Let the server do the NumLock processing. This should only be required
# when using pre-R6 clients
# ServerNumLock
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Xleds 1 2 3
# To set the LeftAlt to Meta, RightAlt key to ModeShift,
# RightCtl key to Compose, and ScrollLock key to ModeLock:
LeftAlt Meta
RightAlt Meta
# RightCtl Control
# ScrollLock Compose
# To disable the XKEYBOARD extension, uncomment XkbDisable.
XkbDisable
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# XkbModel "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# XkbModel "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# XkbLayout "de"
# or:
# XkbLayout "es"
# XkbVariant "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# XkbOptions "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# XkbRules "xfree86"
# XkbModel "pc101"
# XkbLayout "us"
# XkbVariant ""
# XkbOptions ""
XkbKeymap "xfree86(us)"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "Pointer"
Protocol "PS/2"
Device "/dev/mouse"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
# Protocol "Xqueue"
# Baudrate and SampleRate are only for some Logitech mice
# BaudRate 9600
# SampleRate 150
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Emulate3Buttons
Emulate3Timeout 50
# ChordMiddle is an option for some 3-button Logitech mice
# ChordMiddle
EndSection
# **********************************************************************
# Xinput section -- this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "Xinput"
# SubSection "WacomStylus"
# Port "/dev/ttyS1"
# DeviceName "Wacom"
# EndSubSection
# SubSection "WacomCursor"
# Port "/dev/ttyS1"
# EndSubSection
# SubSection "WacomEraser"
# Port "/dev/ttyS1"
# EndSubSection
#
# SubSection "Elographics"
# Port "/dev/ttyS1"
# DeviceName "Elo"
# MinimumXPosition 300
# MaximumXPosition 3500
# MinimumYPosition 300
# MaximumYPosition 3500
# Screen 0
# UntouchDelay 10
# ReportDelay 10
# EndSubSection
#
# SubSection "Joystick"
# Port "/dev/joy0"
# DeviceName "Joystick"
# TimeOut 10
# MinimumXPosition 100
# MaximumXPosition 1300
# MinimumYPosition 100
# MaximumYPosition 1100
# # CenterX 700
# # CenterY 600
# Delta 20
# EndSubSection
#
# The Mouse Subsection contains the same type of entries as the
# standard Pointer Section (see above), with the addition of the
# DeviceName entry.
#
# SubSection "Mouse"
# Port "/dev/mouse2"
# DeviceName "Second Mouse"
# Protocol "Logitech"
# EndSubSection
# EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "My Monitor"
VendorName "Unknown"
ModelName "Unknown"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
HorizSync 31-58
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-110
# This is a set of standard mode timings. Modes that are out of monitor spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.
# 320x200 @ 70 Hz, 31.5 kHz hsync, 8:5 aspect ratio
Modeline "320x200" 12.588 320 344 392 400 200 208 209 225
# 320x240 @ 60 Hz, 31.5 kHz hsync, 4:3 aspect ratio
Modeline "320x240" 12.588 320 348 396 400 240 245 246 262
# 640x400 @ 70 Hz, 31.5 kHz hsync
Modeline "640x400" 25.175 640 676 772 788 400 417 419 458
# 640x480 @ 60 Hz, 31.5 kHz hsync
Modeline "640x480" 25.175 640 676 772 780 480 491 493 521
# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600" 50.00 800 856 976 1040 600 633 639 650 +hsync +vsync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768" 65 1024 1056 1200 1340 768 775 781 814 -hsync
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Generic SVGA"
VendorName "Unknown"
BoardName "Unknown"
Chipset "sis86c205"
MemBase 0x020000000
#Option "nolinear"
Option "noaccel"
Option "no_bitblt"
Option "no_imageblt"
# La opciOn no_bitblt tengo que ponerla para que funcione el server
# o en vez de esta la no_imageblt, con el resto no noto la diferencia
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
Section "Screen"
Driver "SVGA"
Device "Generic SVGA"
Monitor "My Monitor"
# DefaultColorDepth 16
BlankTime 0
SuspendTime 0
OffTime 0
Subsection "Display"
Depth 8
Modes "640x480" "800x600" "1024x768" "320x240" "640x400"
ViewPort 0 0
# Virtual 1280 768
EndSubsection
SubSection "Display"
Depth 16
Modes "640x480" "800x600" "1024x768" "320x240" "640x400"
ViewPort 0 0
# Virtual 1280 768
EndSubsection
SubSection "Display"
Depth 24
Modes "640x480" "800x600" "1024x768" "320x240" "640x400"
EndSubsection
EndSection
Reply to: