placa de rede não funciona
Olá pessoAll,
estou com um computador com placa mãe Soyo KT400 Dragon Lite, Placas de
Rede 3Com 3c905b e uma VIA on-board.
com o kernel 2.2.x vai blz... mas qualquer kernel 2.4.x, as placas de rede
simplismente não pingam... e ainda fica aparecendo uma mensagem de erro
quanto ao irq. segue em anexo o resultado do dmesg.
Obs.: já tirei do setup as referências quanto à Sistema Operacional plug
and play. Já tentei colocar no lilo append="acpi=off apm=off"
Já tentei também com o kernel 2.5.74, mas não consegui fazer funcionar os
módulos... mas a prioridade está sendo funcionar as interfaces em um
kernel >= 2.4.x
Se alguém tiver alguma idéia...
000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f5c30
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=2.4.21 ro root=302
Initializing CPU#0
Detected 2166.485 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4325.37 BogoMIPS
Memory: 515520k/524224k available (1446k kernel code, 8316k reserved, 663k data, 108k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU0: AMD Athlon(tm) XP 3000+ stepping 00
per-CPU timeslice cutoff: 1462.69 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-17, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 001 01 1 1 0 1 0 1 1 71
0c 001 01 0 0 0 0 0 1 1 79
0d 001 01 0 0 0 0 0 1 1 81
0e 001 01 0 0 0 0 0 1 1 89
0f 001 01 0 0 0 0 0 1 1 91
10 001 01 1 1 0 1 0 1 1 71
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 1 0 1 1 99
13 001 01 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:19
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:18
IRQ11 -> 0:11-> 0:16
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2166.4655 MHz.
..... host bus clock speed is 333.3024 MHz.
cpu: 0, clocks: 3333024, slice: 1666512
CPU0<T0:3333024,T1:1666512,D:0,S:1666512,C:3333024>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/3177] at 00:11.0
PCI->APIC IRQ transform: (B0,I10,P0) -> 18
PCI->APIC IRQ transform: (B0,I14,P0) -> 19
PCI->APIC IRQ transform: (B0,I17,P0) -> 11
PCI->APIC IRQ transform: (B0,I18,P0) -> 16
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
[drm] AGP 0.99 on VIA Apollo KT400 @ 0xe0000000 64MB
[drm] Initialized radeon 1.1.1 20010405 on minor 0
[drm] AGP 0.99 on VIA Apollo KT400 @ 0xe0000000 64MB
[drm] Initialized i810 1.2.0 20010920 on minor 1
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: ST340014A, ATA DISK drive
hdd: HL-DT-ST CD-ROM GCR-8520B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63
hdd: attached ide-cdrom driver.
hdd: ATAPI 52X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 108k freed
Adding Swap: 257000k swap-space (priority -1)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0a.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xd000. Vers LK1.1.16
00:10:5a:c9:7e:07, IRQ 18
product code 5152 rev 00.12 date 11-01-98
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
Enabling bus-master transmits and whole-frame receives.
00:0a.0: scatter/gather enabled. h/w checksums enabled
via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth1: VIA VT6102 Rhine-II at 0xe800, 00:50:2c:07:9e:51, IRQ 16.
eth1: MII PHY found at address 1, status 0x7809 advertising 01e1 Link 0000.
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
cmpci: version $Revision: 5.64 $ time 17:41:45 Sep 1 2003
cmpci: found CM8738 adapter at io 0xd400 irq 19
cmpci: chip version = 055
cmpci: Inverse SPDIF-in
cmpci: Enable SPDIF loop
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e601.
diagnostics: net 0cd8 media 8880 dma 0000003a.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
Flags; bus-master 1, dirty 16(0) current 16(0)
Transmit list 00000000 vs. df8d2200.
0: @df8d2200 length 8000002a status 0001002a
1: @df8d2240 length 8000002a status 0001002a
2: @df8d2280 length 8000002a status 0001002a
3: @df8d22c0 length 8000002a status 0001002a
4: @df8d2300 length 8000002a status 0001002a
5: @df8d2340 length 8000002a status 0001002a
6: @df8d2380 length 8000002a status 0001002a
7: @df8d23c0 length 8000002a status 0001002a
8: @df8d2400 length 8000002a status 0001002a
9: @df8d2440 length 8000002a status 0001002a
10: @df8d2480 length 8000002a status 0001002a
11: @df8d24c0 length 8000002a status 0001002a
12: @df8d2500 length 8000002a status 0001002a
13: @df8d2540 length 8000002a status 0001002a
14: @df8d2580 length 8000002a status 8001002a
15: @df8d25c0 length 8000002a status 8001002a
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e601.
diagnostics: net 0cd8 media 8880 dma 0000003a.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
Flags; bus-master 1, dirty 32(0) current 32(0)
Transmit list 00000000 vs. df8d2200.
0: @df8d2200 length 8000002a status 0001002a
1: @df8d2240 length 8000002a status 0001002a
2: @df8d2280 length 8000002a status 0001002a
3: @df8d22c0 length 8000002a status 0001002a
4: @df8d2300 length 8000002a status 0001002a
5: @df8d2340 length 8000002a status 0001002a
6: @df8d2380 length 8000002a status 0001002a
7: @df8d23c0 length 8000002a status 0001002a
8: @df8d2400 length 8000002a status 0001002a
9: @df8d2440 length 8000002a status 0001002a
10: @df8d2480 length 8000002a status 0001002a
11: @df8d24c0 length 8000002a status 0001002a
12: @df8d2500 length 80000062 status 00010062
13: @df8d2540 length 80000062 status 00010062
14: @df8d2580 length 80000062 status 80010062
15: @df8d25c0 length 80000062 status 80010062
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e601.
diagnostics: net 0cd8 media 8880 dma 0000003a.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
Flags; bus-master 1, dirty 48(0) current 48(0)
Transmit list 00000000 vs. df8d2200.
0: @df8d2200 length 80000062 status 00010062
1: @df8d2240 length 80000062 status 00010062
2: @df8d2280 length 80000062 status 00010062
3: @df8d22c0 length 80000062 status 00010062
4: @df8d2300 length 80000062 status 00010062
5: @df8d2340 length 80000062 status 00010062
6: @df8d2380 length 80000062 status 00010062
7: @df8d23c0 length 8000002a status 0001002a
8: @df8d2400 length 8000002a status 0001002a
9: @df8d2440 length 8000002a status 0001002a
10: @df8d2480 length 8000002a status 0001002a
11: @df8d24c0 length 8000002a status 0001002a
12: @df8d2500 length 8000002a status 0001002a
13: @df8d2540 length 80000062 status 00010062
14: @df8d2580 length 80000062 status 80010062
15: @df8d25c0 length 80000062 status 80010062
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e601.
diagnostics: net 0cd8 media 8880 dma 0000003a.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
Flags; bus-master 1, dirty 64(0) current 64(0)
Transmit list 00000000 vs. df8d2200.
0: @df8d2200 length 80000062 status 00010062
1: @df8d2240 length 80000062 status 00010062
2: @df8d2280 length 80000062 status 00010062
3: @df8d22c0 length 80000062 status 00010062
4: @df8d2300 length 80000062 status 00010062
5: @df8d2340 length 80000062 status 00010062
6: @df8d2380 length 80000062 status 00010062
7: @df8d23c0 length 80000062 status 00010062
8: @df8d2400 length 80000062 status 00010062
9: @df8d2440 length 80000062 status 00010062
10: @df8d2480 length 80000062 status 00010062
11: @df8d24c0 length 80000062 status 00010062
12: @df8d2500 length 80000062 status 00010062
13: @df8d2540 length 80000062 status 00010062
14: @df8d2580 length 80000062 status 80010062
15: @df8d25c0 length 80000062 status 80010062
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e601.
diagnostics: net 0cd8 media 8880 dma 0000003a.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
Flags; bus-master 1, dirty 80(0) current 80(0)
Transmit list 00000000 vs. df8d2200.
0: @df8d2200 length 80000062 status 00010062
1: @df8d2240 length 80000062 status 00010062
2: @df8d2280 length 80000062 status 00010062
3: @df8d22c0 length 80000062 status 00010062
4: @df8d2300 length 80000062 status 00010062
5: @df8d2340 length 80000062 status 00010062
6: @df8d2380 length 80000062 status 00010062
7: @df8d23c0 length 80000062 status 00010062
8: @df8d2400 length 80000062 status 00010062
9: @df8d2440 length 80000062 status 00010062
10: @df8d2480 length 80000062 status 00010062
11: @df8d24c0 length 80000062 status 00010062
12: @df8d2500 length 80000062 status 00010062
13: @df8d2540 length 80000062 status 00010062
14: @df8d2580 length 80000062 status 80010062
15: @df8d25c0 length 80000062 status 80010062
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e601.
diagnostics: net 0cd8 media 8880 dma 0000003a.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
Flags; bus-master 1, dirty 96(0) current 96(0)
Transmit list 00000000 vs. df8d2200.
0: @df8d2200 length 80000062 status 00010062
1: @df8d2240 length 80000062 status 00010062
2: @df8d2280 length 80000062 status 00010062
3: @df8d22c0 length 80000062 status 00010062
4: @df8d2300 length 8000002a status 0001002a
5: @df8d2340 length 80000062 status 00010062
6: @df8d2380 length 8000002a status 0001002a
7: @df8d23c0 length 80000062 status 00010062
8: @df8d2400 length 80000062 status 00010062
9: @df8d2440 length 80000062 status 00010062
10: @df8d2480 length 80000062 status 00010062
11: @df8d24c0 length 80000062 status 00010062
12: @df8d2500 length 8000002a status 0001002a
13: @df8d2540 length 80000062 status 00010062
14: @df8d2580 length 8000002a status 8001002a
15: @df8d25c0 length 8000002a status 8001002a
eth0: Resetting the Tx ring pointer.
Reply to: