Re: Etch Bootvorgang, USB-Disketten-Laufwerk
Hallo Dirk,
Am Mittwoch 06 Februar 2008 08:35 schrieben Sie:
> Hallo Manfred,
>
> 2008/2/6, Manfred Rebentisch <debianlist@comparat.de>:
> > Hallo,
> > ich habe an meinem PC ein über USB angeschlossenes Gerät mit CardReader
> > und Diskettenlaufwerk (im PC ist kein Floppy eingebaut). Seitdem ich Etch
> > installiert habe, wird beim Booten dieses Diskettenlaufwerk getestet.
> > Wenn keine Disk drin ist, dauert es mehrere Minuten, bis der Bootvorgang
> > weiterläuft. Mit Diskette wird wie zu altem IBM-Zeiten ein intensiver
> > Floppy-Test gefahren.
>
> [...]
> Wann genau wird der Test gemacht -- beim Suchen des Rootfilesystems?
> Verwendest Du ein initramfs -- wenn ja welches Werkzeug zu seiner
> Erzeugung ("initramfs-tools" oder "yaird")?
>
> Dirk
Ich glaube beim Starten von kjournald.
Ich habe einen USB-Scanner angeschlossen und eben dieses Gerät "MITSUMI USB
7-in-1 Media Drive" (FA401).
Ich trage mal ein paar USB-Infos aus dmesg her:
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 169
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 169, io mem 0xcfffd000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 177
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 177, io mem 0xcfffe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:03.2[D] -> GSI 23 (level, low) -> IRQ 185
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:03.2
ehci_hcd 0000:00:03.2: irq 185, io mem 0xcffff000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
[...]
usb 3-4: new high speed USB device using ehci_hcd and address 3
usb 3-4: configuration #1 chosen from 1 choice
ohci_hcd 0000:00:03.0: wakeup
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-2: new full speed USB device using ohci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011060000006027]
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
usb 1-2.1: new full speed USB device using ohci_hcd and address 4
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.2: new full speed USB device using ohci_hcd and address 5
usb 1-2.2: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
[...]
kjournald starting. Commit interval 5 seconds
Vendor: OEI-USB Model: MMC/SD Rev: 2.7
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
Vendor: MITSUMI Model: USB FDD Rev: 1043
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: Attached scsi removable disk sda
SCSI device sdb: 1440 512-byte hdwr sectors (1 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 46 1e 00
sdb: assuming drive cache: write through
SCSI device sdb: 1440 512-byte hdwr sectors (1 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 46 1e 00
sdb: assuming drive cache: write through
sdb: unknown partition table
sd 1:0:0:0: Attached scsi removable disk sdb
Manfred
Reply to: