Lenny, Kernel 2.6.25/26, IDE, BX-Chipsatz, I/O Error
Hallo Liste,
nachdem Kernelupdate auf 2.6.26 meinte das System es sollte nach 194
Tagen mal wieder einen fscheck machen. Soweit ganz normal. Dann gab es
jedoch mehrfach folgende Fehlermeldung:
ide: failed opcode was: unknown
end requst: I/O error, dev hda, sector xxxxx
Buffer I/O error on device hda8 logical block xxxx
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: status=0x40 { UncorrectableError } LBAsect=xxxx, sector=xxxx
Gleiches Bild auch mit dem 2.6.25 Kernel (jeweils Debian Pakete aus Lenny).
Da ich nichts anderes zur Hand hatte, habe ich ein SuSE 10.0
Rescuesystem gebootet und dort den fscheck durchgeführt, was problemlos
ging. Das ganze ist reproduzierbar. Unter Debian gibt es die
Fehlermeldung sobald ich einen fscheck auf einer Platte am
Onboardcontroller starte. Sonst läuft das System problemlos.
Noch ein paar Details zur Hardware (die schon recht gut abgehangen ist)
Board: P2B-S (Intel 440 BX Chipsatz)
Eine kurze Suche bei google war erfolglos. Deswegen frage ich mal hier,
ob das Problem vielleicht bekannt ist und bedanke mich schonmal für
Antworten.
Hier noch ein paar gesammelte Infos aus dem System:
hdparm -i /dev/hda
/dev/hda:
Model=IBM-DTLA-305020, FwRev=TW2OA60A, SerialNo=YE0YELT6577
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40188960
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: ATA/ATAPI-2,3,4,5
* signifies the current active mode
hdparm -I /dev/hda
/dev/hda:
ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.
Model Number: IBM-DTLA-305020
Serial Number: YE0YELT6577
Firmware Revision: TW2OA60A
Standards:
Used: ATA/ATAPI-5 T13 1321D revision 1
Supported: 5 4 3 & some of 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 40188960
device size with M = 1024*1024: 19623 MBytes
device size with M = 1000*1000: 20576 MBytes (20 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 40 Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: disabled
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
Release interrupt
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* READ/WRITE_DMA_QUEUED
Advanced Power Management feature set
Power-Up In Standby feature set
SET_FEATURES required to spinup after power up
Address Offset Reserved Area Boot
SET_MAX security extension
Automatic Acoustic Management feature set
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
22min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
smartctl -H /dev/hda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
lspci
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 03)
00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:06.0 SCSI storage controller: Adaptec AHA-2940U2/U2W / 7890/7891
00:0a.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 74)
00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20267
(FastTrak100/Ultra100) (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RF/SG AGP
lsmod | grep ide
ide_cd_mod 27684 0
cdrom 30176 1 ide_cd_mod
ide_disk 10496 14
ide_pci_generic 3908 0 [permanent]
ide_core 92628 5
ide_cd_mod,ide_disk,ide_pci_generic,pdc202xx_old,piix
uname -a
Linux srv01 2.6.26-1-686 #1 SMP Wed Aug 20 12:56:41 UTC 2008 i686 GNU/Linux
Reply to: