MPPE-VPN-Verbindung einrichten
Moin
Ich bekomme meine VPN-Verbindung zum Firmen-Server nicht wirklich zum
Laufen. Das Protokoll:
----------------------------------------------------------------------------
Sep 30 22:40:22 localhost pppd[6918]: pppd 2.4.4 started by root, uid 0
Sep 30 22:40:22 localhost pppd[6918]: Using interface ppp0
Sep 30 22:40:22 localhost pppd[6918]: Connect: ppp0 <--> /dev/pts/4
Sep 30 22:40:22 localhost pptp[6919]: anon log[main:pptp.c:267]: The
synchronous pptp option is NOT activated
Sep 30 22:40:22 localhost pptp[6924]: anon
log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1
'Start-Control-Connection-Request'
Sep 30 22:40:22 localhost pptp[6924]: anon
log[ctrlp_disp:pptp_ctrl.c:738]: Received Start Control Connection Reply
Sep 30 22:40:22 localhost pptp[6924]: anon
log[ctrlp_disp:pptp_ctrl.c:772]: Client connection established.
Sep 30 22:40:23 localhost pptp[6924]: anon
log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7
'Outgoing-Call-Request'
Sep 30 22:40:23 localhost pptp[6924]: anon
log[ctrlp_disp:pptp_ctrl.c:857]: Received Outgoing Call Reply.
Sep 30 22:40:23 localhost pptp[6924]: anon
log[ctrlp_disp:pptp_ctrl.c:896]: Outgoing call established (call ID 0,
peer's call ID 8).
Sep 30 22:40:26 localhost pppd[6918]: CHAP authentication succeeded
Sep 30 22:40:27 localhost pppd[6918]: MPPE 40-bit stateless compression
enabled
Sep 30 22:40:30 localhost pppd[6918]: Cannot determine ethernet address
for proxy ARP
Sep 30 22:40:30 localhost pppd[6918]: local IP address 172.16.xxx.xxx
Sep 30 22:40:30 localhost pppd[6918]: remote IP address 62.109.xxx.xxx
Sep 30 22:41:35 localhost pptp[6924]: anon log[logecho:pptp_ctrl.c:676]:
Echo Request received.
Sep 30 22:41:35 localhost pptp[6924]: anon
log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 6 'Echo-Reply'
Sep 30 22:42:35 localhost pptp[6924]: anon
log[pptp_handle_timer:pptp_ctrl.c:1049]: closing control connection due
to missing echo reply
Sep 30 22:42:35 localhost pptp[6924]: anon
log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12
'Call-Clear-Request'
Sep 30 22:42:35 localhost pptp[6924]: anon
log[pptp_conn_close:pptp_ctrl.c:430]: Closing PPTP connection
Sep 30 22:42:35 localhost pptp[6924]: anon
log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 3
'Stop-Control-Connection-Request'
Sep 30 22:42:35 localhost pptp[6924]: anon
log[call_callback:pptp_callmgr.c:78]: Closing connection (call state)
Sep 30 22:42:35 localhost pppd[6918]: Modem hangup
Sep 30 22:42:35 localhost pppd[6918]: Connect time 2.1 minutes.
Sep 30 22:42:35 localhost pppd[6918]: Sent 749938979 bytes, received 0
bytes.
Sep 30 22:42:35 localhost pppd[6918]: MPPE disabled
Sep 30 22:42:35 localhost pppd[6918]: Connection terminated.
Sep 30 22:42:35 localhost pppd[6918]: Exit.
----------------------------------------------------------------------------
Mir fällt dabei auf, dass das ppp0-Interface 0 bytes erhält. :-(
Zur Server-Einstellung kann ich leider nichts sagen, außer dass ich die
Zugangsdaten habe und damit unter Win erfolgreich die Verbindung
aufbauen kann.
Hat jemand noch ein paar Tipps, wo man drehen könnte?
Danke und Gruß
Rüdiger
--
Reply to: