[OT] PIO Modus statt DMA ab bestimmtem Sektor der HD?
Hallo Liste,
ich habe eine neue P-ATA Platte in mein Fossil eingebaut und bin
erstaunt, daß ab Sektor BlaBla bloß noch Zugriffe im PIO Modus statt,
wie gewohnt, im DMA Modus erfolgen sollen.
hda: cannot use LBA48 DMA - PIO mode will be used for accessing sectors
> 268435456
Der Delinquent ist eine Seagate Barracuda 160 GB 7200.7.
LBA48 kann nicht benutzt werden - sowas!
Die S-ATA Seagates haben am Promise damit keine Probleme. Die kleineren
P-ATA Seagates brauchen scheinbar kein LBA48 (weniger als 268435456
Sektoren).
Welche magische Grenze verlangt hier nach einem Visum? Zu altes BIOS?
Tschüss und vielen Dank im Voraus
dirk
INFO:
System: AMD K6-2, Etch/i386 - Kernel 2.6.18-4-486 (Out of the box. Hab'
noch keinen gebacken)
Auszug aus dmesg:
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ALI15X3: chipset revision 194
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST3160023A, ATA DISK drive
hdb: HL-DT-STDVD-ROM GDR8164B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST3120022A, ATA DISK drive
hdd: ST3120022A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: cannot use LBA48 DMA - PIO mode will be used for accessing sectors
> 268435456
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63,
UDMA(66)
hdb: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdc: max request size: 128KiB
hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63,
UDMA(66)
hdd: max request size: 128KiB
hdd: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63,
UDMA(66)
ata1: SATA link down (SStatus 0 SControl 300)
scsi1 : sata_promise
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-6, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi2 : sata_promise
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_promise
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-6, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
Vendor: ATA Model: ST3160827AS Rev: 3.42
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3160827AS Rev: 3.42
Type: Direct-Access ANSI SCSI revision: 05
Reply to: