Trekstor i.beat organix mounten
Hey Liste!
Wenn ich meinen Trekstor über USB an meinem Laptop anstecke, bekomme
ich folgende Fehler, mitdenen ich nichts anzufangen weiß:
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x183f, Product: 0x0101, Revision: 0x1001
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: *** thread sleeping.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00
len=1
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL
6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: TrekStor Model: i.Beat_organix. Rev: 0100
Type: Direct-Access ANSI SCSI revision: 04
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
Fehlt da irgendei Modul? Könnte durchaus sein, weil hier ein
selbstgebauter 2.6.19 Kernel mit fest eincompilierten Modulen läuft.
Ansonsten meldet sich weder hal, noch kann ich den Player manuell
mounten, da kein Device vorhanden ist.
Laut Trekstor ist ein Betrieb mit dem 2.6 Kernel möglich.
Hat jemand einen Tipp für mich, was da falschläuft?
Danke und Tschau
Sandro
Reply to: