Re: Adaptec 3200S RAID-Controller unter Debian
> --- Ursprüngliche Nachricht ---
> Von: Markus Boas <ryven@gmx.de>
> An: debian-user-german@lists.debian.org
> Betreff: Re: Adaptec 3200S RAID-Controller unter Debian
> Datum: Tue, 23 Aug 2005 07:05:30 +0200
>
> Am Dienstag 23 August 2005 00:13 schrieb Sebastian Brüchner:
> > Hallo @ all,
> >
> > ich habe folgendes Problem:
> > Ich möchte unter Debian ein Hardwareraid mit einem Adaptec 3200S
> > Raidcontroller realisieren. Nun habe ich schon statt des 2.4er Kernels
> den
> > 2.6.8er Kernel zusammengebaut und der Controller sowie die beiden RAID
> Sets
> > werden beim Starten auch erkannt.
> > Mein Problem ist jetzt, dass ich die RAIDs nicht partitionieren kann.
> Wenn
> > ich "cfdisk /dev/sda" versuche auszuführen, hängt die Konsole und ich
> kann
> > den Prozess auch nicht mehr "killen".
> > Da das ganze über das i2o System läuft, dachte ich, dass es vielleicht
> über
> > "/dev/i2o/sda" zu regeln wäre aber "/dev/i2o" existiert schon nicht.
>
> Der Ansatz war richtig, über i2o sind die Platten dann aber hda.
> Zumindest wars bei mir mit 3410s so.
Das habe ich auch überprüft, da sagt er mir aber auch, dass keine Festplatte
vorhanden ist. Ausserdem hat er beim Booten (DMESG) folgendes ausgegeben:
<snip>
SCSI device sda: 71131136 512-byte hdwr sectors (36419 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SCSI device sdb: 250904576 512-byte hdwr sectors (128463 MB)
SCSI device sdb: drive cache: write through
sdb: unknown partition table
<snip>
Was den beiden Raids entspricht.
>
> Ok gibt mir mal bitte nur das cat /proc/scsi/scsi.
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: ADAPTEC Model: RAID-5 Rev: 370F
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: ADAPTEC Model: RAID-0 Rev: 370F
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 06 Lun: 00
Vendor: SEAGATE Model: SX150176LC Rev: BA08
Type: Direct-Access ANSI SCSI revision: 02
Auch hier, wird alles richtig anzeigeigt.
> Zudem sieht das hier aus als hättest du die dt_i2o Module erst geladen und
> dann den Kontroller zusätzlich über i2o angesproche.
Das hatte ich zu Anfangs auch gemacht, dann habe ich das aber festgestellt
und das i2o Modul aus dem Kernel geschmissen und nur noch das dpt_i2o drin
gelassen
> Ist der 3200s in der Performance auch so schlecht wie der 3400s?
Kann ich nicht beurteilen, habe den 3400S noch nicht in den Fingern gehabt.
Dürften sich an und für sich ja nicht großartig unterscheiden, da der 3400S
ja im Prinzip der selbe Controller ist, nur mit Daugtherboard als
Kanalerweiterung. Oder irre ich mich?
>
> Mfg
> Ryven
Gruß
Sebastian
>
> >
> > Ich bin echt Ratlos.
> >
> > Hoffentlich kann mir jemand helfen.
> >
> > Vielen Dank schonmal im voraus!
> >
> > Gruß
> >
> > Sebastian
> >
> > Anbei noch ein DMESG:
> >
> > hashdb:/# dmesg
> > Linux version 2.6.8 (root@hashdb) (gcc version 3.3.5 (Debian
> 1:3.3.5-13))
> > #2 Sun Aug 21 03:48:28 CEST 2005
> > BIOS-provided physical RAM map:
> > BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> > BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
> > BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
> > BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
> > BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
> > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> > 511MB LOWMEM available.
> > On node 0 totalpages: 131052
> > DMA zone: 4096 pages, LIFO batch:1
> > Normal zone: 126956 pages, LIFO batch:16
> > HighMem zone: 0 pages, LIFO batch:1
> > DMI 2.3 present.
> > ACPI: RSDP (v000 ASUS ) @ 0x000f6a10
> > ACPI: RSDT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec000
> > ACPI: FADT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec080
> > ACPI: BOOT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec040
> > ACPI: DSDT (v001 ASUS A7V-133 0x00001000 MSFT 0x0100000b) @ 0x00000000
> > Built 1 zonelists
> > Kernel command line: BOOT_IMAGE=LinuxNEW2 ro root=822
> > Local APIC disabled by BIOS -- reenabling.
> > Found and enabled local APIC!
> > Initializing CPU#0
> > PID hash table entries: 2048 (order 11: 16384 bytes)
> > Detected 1273.397 MHz processor.
> > Using tsc for high-res timesource
> > Console: colour VGA+ 80x25
> > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> > Memory: 515068k/524208k available (2138k kernel code, 8392k reserved,
> 895k
> > data, 164k init, 0k highmem)
> > Checking if this processor honours the WP bit even in supervisor mode...
> > Ok. Calibrating delay loop... 2498.56 BogoMIPS
> > Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> > CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000
> > CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000
> > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> > CPU: L2 Cache: 256K (64 bytes/line)
> > CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020
> > CPU: AMD Athlon(tm) Processor stepping 02
> > Enabling fast FPU save and restore... done.
> > Checking 'hlt' instruction... OK.
> > enabled ExtINT on CPU#0
> > ESR value before enabling vector: 00000000
> > ESR value after enabling vector: 00000000
> > Using local APIC timer interrupts.
> > calibrating APIC timer ...
> > ..... CPU clock speed is 1273.0020 MHz.
> > ..... host bus clock speed is 268.0004 MHz.
> > NET: Registered protocol family 16
> > PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=3
> > PCI: Using configuration type 1
> > mtrr: v2.0 (20020519)
> > ACPI: Subsystem revision 20040326
> > ACPI: IRQ9 SCI: Edge set to Level Trigger.
> > ACPI: Interpreter enabled
> > ACPI: Using PIC for interrupt routing
> > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
> > ACPI: PCI Root Bridge [PCI0] (00:00)
> > PCI: Probing PCI hardware (bus 00)
> > Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f ->
> 09
> > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> > SCSI subsystem initialized
> > PCI: Using ACPI for IRQ routing
> > ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15
> > ACPI: PCI interrupt 0000:00:04.2[D] -> GSI 15 (level, low) -> IRQ 15
> > ACPI: PCI interrupt 0000:00:04.3[D] -> GSI 15 (level, low) -> IRQ 15
> > ACPI: PCI interrupt 0000:00:09.1[A] -> GSI 15 (level, low) -> IRQ 15
> > ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
> > ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
> > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3
> > ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 3 (level, low) -> IRQ 3
> > ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
> > ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 10 (level, low) -> IRQ 10
> > ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 15 (level, low) -> IRQ 15
> > ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 11 (level, low) -> IRQ 11
> > ACPI: PCI interrupt 0000:03:07.0[A] -> GSI 3 (level, low) -> IRQ 3
> > spurious 8259A interrupt: IRQ7.
> > vesafb: probe of vesafb0 failed with error -6
> > vga16fb: initializing
> > vga16fb: mapped to 0xc00a0000
> > fb0: VGA16 VGA frame buffer device
> > Simple Boot Flag at 0x3a set to 0x1
> > NTFS driver 2.1.15 [Flags: R/O].
> > udf: registering filesystem
> > Initializing Cryptographic API
> > Applying VIA southbridge workaround.
> > PCI: Disabling Via external APIC routing
> > Real Time Clock Driver v1.12
> > Using anticipatory io scheduler
> > Floppy drive(s): fd0 is 1.44M
> > FDC 0 is a post-1991 82077
> > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> > loop: loaded (max 8 devices)
> > pcnet32.c:v1.30i 06.28.2004 tsbogend@alpha.franken.de
> > Loading Adaptec I2O RAID: Version 2.4 Build 5go
> > Detecting Adaptec I2O RAID controllers...
> > ACPI: PCI interrupt 0000:00:09.1[A] -> GSI 15 (level, low) -> IRQ 15
> > Adaptec I2O RAID controller 0 at e0824000 size=100000 irq=15
> > dpti: If you have a lot of devices this could take a few minutes.
> > dpti0: Reading the hardware resource table.
> > TID 008 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001
> > TID 009 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001
> > TID 531 Vendor: ADAPTEC Device: RAID-5 Rev: 370F
> > TID 537 Vendor: ADAPTEC Device: RAID-0 Rev: 370F
> > scsi0 : Vendor: Adaptec Model: 3200S FW:370F
> > Vendor: ADAPTEC Model: RAID-5 Rev: 370F
> > Type: Direct-Access ANSI SCSI revision: 02
> > Vendor: ADAPTEC Model: RAID-0 Rev: 370F
> > Type: Direct-Access ANSI SCSI revision: 02
> > ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
> > scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
> >
> > aic7892: Ultra160 Wide Channel A, SCSI Id=15, 32/253 SCBs
> >
> > (scsi1:A:3): 20.000MB/s transfers (20.000MHz, offset 16)
> > (scsi1:A:6): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
> > Vendor: TEAC Model: CD-ROM CD-532S Rev: 1.0A
> > Type: CD-ROM ANSI SCSI revision: 02
> > Vendor: SEAGATE Model: SX150176LC Rev: BA08
> > Type: Direct-Access ANSI SCSI revision: 02
> > scsi1:A:6:0: Tagged Queuing enabled. Depth 8
> > SCSI device sda: 71131136 512-byte hdwr sectors (36419 MB)
> > SCSI device sda: drive cache: write back
> > sda: unknown partition table
> > Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
> > SCSI device sdb: 250904576 512-byte hdwr sectors (128463 MB)
> > SCSI device sdb: drive cache: write through
> > sdb: unknown partition table
> > Attached scsi disk sdb at scsi0, channel 0, id 4, lun 0
> > SCSI device sdc: 97693755 512-byte hdwr sectors (50019 MB)
> > SCSI device sdc: drive cache: write through
> > sdc: sdc1 sdc2 sdc3
> > Attached scsi disk sdc at scsi1, channel 0, id 6, lun 0
> > sr0: scsi3-mmc drive: 0x/0x caddy
> > Uniform CD-ROM driver Revision: 3.20
> > Attached scsi CD-ROM sr0 at scsi1, channel 0, id 3, lun 0
> > mice: PS/2 mouse device common for all mice
> > serio: i8042 AUX port at 0x60,0x64 irq 12
> > serio: i8042 KBD port at 0x60,0x64 irq 1
> > input: AT Translated Set 2 keyboard on isa0060/serio0
> > I2O Core - (C) Copyright 1999 Red Hat Software
> > I2O: Event thread created as pid 163
> > i2o: Checking for PCI I2O controllers...
> > ACPI: PCI interrupt 0000:00:09.1[A] -> GSI 15 (level, low) -> IRQ 15
> > i2o: I2O controller on bus 0 at 73.
> > i2o: PCI I2O controller at E0000000 size=33554432
> > I2O: MTRR workaround for Intel i960 processor
> > i2o/iop0: Installed at IRQ15
> > i2o: 1 I2O controller found and installed.
> > Activating I2O controllers...
> > This may take a few minutes if there are many devices
> > dpti: Could Not find task 0 in wait queue
> > Tasks in wait queue:
> > i2o_scsi.c: Version 0.1.2
> > chain_pool: 0 bytes @ c15edd60
> > (512 byte buffers X 4 can_queue X 0 i2o controllers)
> > NET: Registered protocol family 2
> > IP: routing cache hash table of 4096 buckets, 32Kbytes
> > TCP: Hash tables configured (established 32768 bind 65536)
> > NET: Registered protocol family 1
> > NET: Registered protocol family 17
> > ACPI: (supports S0 S1 S4 S5)
> > kjournald starting. Commit interval 5 seconds
> > EXT3-fs: mounted filesystem with ordered data mode.
> > VFS: Mounted root (ext3 filesystem) readonly.
> > Freeing unused kernel memory: 164k freed
> > Adding 995988k swap on /dev/sdc1. Priority:-1 extents:1
> > EXT3 FS on sdc2, internal journal
> > 0000:03:04.0: DC21143 at 0x9800, h/w address 00:c0:95:e2:b6:44,
> > and requires IRQ10 (provided by PCI BIOS).
> > de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
> > 0000:03:05.0: DC21143 at 0x9400, h/w address 00:c0:95:e2:b6:45,
> > and requires IRQ15 (provided by PCI BIOS).
> > de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
> > 0000:03:06.0: DC21143 at 0x9000, h/w address 00:c0:95:e2:b6:46,
> > and requires IRQ11 (provided by PCI BIOS).
> > de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
> > 0000:03:07.0: DC21143 at 0x8800, h/w address 00:c0:95:e2:b6:47,
> > and requires IRQ3 (provided by PCI BIOS).
> > de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
> > I2O Block Storage OSM v0.9
> > (c) Copyright 1999-2001 Red Hat Software.
> > i2o_block: registered device at major 80
> > i2o_block: Checking for Boot device...
> > i2o_block: Checking for I2O Block devices...
> > I2O configuration manager v 0.04.
> > (C) Copyright 1999 Red Hat Software
> > kjournald starting. Commit interval 5 seconds
> > EXT3 FS on sdc3, internal journal
> > EXT3-fs: mounted filesystem with ordered data mode.
> > eth0: media is 100Mb/s.
> >
> > Und ein LSPCI -v:
> >
> > hashdb:/# lspci -v
> > 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365
> [KT133/KM133]
> > (rev 03)
> > Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
> > Flags: bus master, medium devsel, latency 8
> > Memory at e4000000 (32-bit, prefetchable) [size=64M]
> > Capabilities: [a0] AGP version 2.0
> > Capabilities: [c0] Power Management version 2
> >
> > 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133
> > AGP] (prog-if 00 [Normal decode])
> > Flags: bus master, 66MHz, medium devsel, latency 0
> > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> > Memory behind bridge: de000000-dfcfffff
> > Prefetchable memory behind bridge: e3f00000-e3ffffff
> > Capabilities: [80] Power Management version 2
> >
> > 0000:00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
> > South] (rev 40)
> > Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
> > Flags: bus master, stepping, medium devsel, latency 0
> > Capabilities: [c0] Power Management version 2
> >
> > 0000:00:04.1 IDE interface: VIA Technologies, Inc.
> > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
> (prog-if
> > 8a [Master SecP PriP])
> > Flags: medium devsel
> > I/O ports at d800 [disabled] [size=16]
> > Capabilities: [c0] Power Management version 2
> >
> > 0000:00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
> 1.1
> > Controller (rev 16) (prog-if 00 [UHCI])
> > Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
> > Flags: bus master, medium devsel, latency 32, IRQ 15
> > I/O ports at d400 [size=32]
> > Capabilities: [80] Power Management version 2
> >
> > 0000:00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
> 1.1
> > Controller (rev 16) (prog-if 00 [UHCI])
> > Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
> > Flags: bus master, medium devsel, latency 32, IRQ 15
> > I/O ports at d000 [size=32]
> > Capabilities: [80] Power Management version 2
> >
> > 0000:00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> > (rev 40)
> > Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
> > Flags: medium devsel, IRQ 9
> > Capabilities: [68] Power Management version 2
> >
> > 0000:00:09.0 PCI bridge: Adaptec (formerly DPT) PCI Bridge (rev 02)
> > (prog-if 00 [Normal decode])
> > Flags: bus master, medium devsel, latency 32
> > Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
> > Capabilities: [68] Power Management version 2
> >
> > 0000:00:09.1 0ebc: Adaptec (formerly DPT) SmartRAID V Controller (rev
> 02)
> > (prog-if 03)
> > Subsystem: Adaptec (formerly DPT) 3000S Ultra3 Dual Channel
> > Flags: bus master, medium devsel, latency 64, IRQ 15
> > BIST result: 00
> > Memory at e0000000 (32-bit, prefetchable) [size=32M]
> > Capabilities: [80] Power Management version 2
> >
> > 0000:00:0a.0 PCI bridge: Digital Equipment Corporation DECchip 21152
> (rev
> > 03) (prog-if 00 [Normal decode])
> > Flags: bus master, medium devsel, latency 32
> > Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
> > I/O behind bridge: 00008000-00009fff
> > Memory behind bridge: dc000000-ddffffff
> > Prefetchable memory behind bridge: 00000000dfe00000-00000000dfe00000
> > Capabilities: [dc] Power Management version 1
> >
> > 0000:00:0c.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
> > Subsystem: Adaptec 29160 Ultra160 SCSI Controller
> > Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
> > BIST result: 00
> > I/O ports at 7800 [disabled] [size=256]
> > Memory at db800000 (64-bit, non-prefetchable) [size=4K]
> > Capabilities: [dc] Power Management version 2
> >
> > 0000:01:01.0 VGA compatible controller: Trident Microsystems 3DImage
> 9750
> > (rev f3) (prog-if 00 [VGA])
> > Subsystem: Trident Microsystems 3DImage 9750
> > Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency 64,
> IRQ
> > 3
> > Memory at df000000 (32-bit, non-prefetchable) [size=4M]
> > Memory at de800000 (32-bit, non-prefetchable) [size=128K]
> > Memory at de000000 (32-bit, non-prefetchable) [size=4M]
> > Expansion ROM at e3ff0000 [disabled] [size=64K]
> >
> > 0000:03:04.0 Ethernet controller: Digital Equipment Corporation DECchip
> > 21142/43 (rev 41)
> > Subsystem: Znyx Advanced Systems: Unknown device 0013
> > Flags: bus master, medium devsel, latency 96, IRQ 10
> > I/O ports at 9800 [size=128]
> > Memory at dd800000 (32-bit, non-prefetchable) [size=1K]
> >
> > 0000:03:05.0 Ethernet controller: Digital Equipment Corporation DECchip
> > 21142/43 (rev 41)
> > Subsystem: Znyx Advanced Systems: Unknown device 0013
> > Flags: bus master, medium devsel, latency 96, IRQ 15
> > I/O ports at 9400 [size=128]
> > Memory at dd000000 (32-bit, non-prefetchable) [size=1K]
> >
> > 0000:03:06.0 Ethernet controller: Digital Equipment Corporation DECchip
> > 21142/43 (rev 41)
> > Subsystem: Znyx Advanced Systems: Unknown device 0013
> > Flags: bus master, medium devsel, latency 96, IRQ 11
> > I/O ports at 9000 [size=128]
> > Memory at dc800000 (32-bit, non-prefetchable) [size=1K]
> >
> > 0000:03:07.0 Ethernet controller: Digital Equipment Corporation DECchip
> > 21142/43 (rev 41)
> > Subsystem: Znyx Advanced Systems: Unknown device 0013
> > Flags: bus master, medium devsel, latency 96, IRQ 3
> > I/O ports at 8800 [size=128]
> > Memory at dc000000 (32-bit, non-prefetchable) [size=1K]
>
Reply to: