Adaptec 3200S RAID-Controller unter Debian
Hallo @ all,
ich habe folgendes Problem:
Ich möchte unter Debian ein Hardwareraid mit einem Adaptec 3200S
Raidcontroller realisieren. Nun habe ich schon statt des 2.4er Kernels den
2.6.8er Kernel zusammengebaut und der Controller sowie die beiden RAID Sets
werden beim Starten auch erkannt.
Mein Problem ist jetzt, dass ich die RAIDs nicht partitionieren kann. Wenn
ich "cfdisk /dev/sda" versuche auszuführen, hängt die Konsole und ich kann
den Prozess auch nicht mehr "killen".
Da das ganze über das i2o System läuft, dachte ich, dass es vielleicht über
"/dev/i2o/sda" zu regeln wäre aber "/dev/i2o" existiert schon nicht.
Ich bin echt Ratlos.
Hoffentlich kann mir jemand helfen.
Vielen Dank schonmal im voraus!
Gruß
Sebastian
Anbei noch ein DMESG:
hashdb:/# dmesg
Linux version 2.6.8 (root@hashdb) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #2
Sun Aug 21 03:48:28 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131052
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126956 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS ) @ 0x000f6a10
ACPI: RSDT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec000
ACPI: FADT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec080
ACPI: BOOT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec040
ACPI: DSDT (v001 ASUS A7V-133 0x00001000 MSFT 0x0100000b) @ 0x00000000
Built 1 zonelists
Kernel command line: BOOT_IMAGE=LinuxNEW2 ro root=822
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1273.397 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 515068k/524208k available (2138k kernel code, 8392k reserved, 895k
data, 164k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2498.56 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1273.0020 MHz.
..... host bus clock speed is 268.0004 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15
ACPI: PCI interrupt 0000:00:04.2[D] -> GSI 15 (level, low) -> IRQ 15
ACPI: PCI interrupt 0000:00:04.3[D] -> GSI 15 (level, low) -> IRQ 15
ACPI: PCI interrupt 0000:00:09.1[A] -> GSI 15 (level, low) -> IRQ 15
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3
ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 15 (level, low) -> IRQ 15
ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:03:07.0[A] -> GSI 3 (level, low) -> IRQ 3
spurious 8259A interrupt: IRQ7.
vesafb: probe of vesafb0 failed with error -6
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb0: VGA16 VGA frame buffer device
Simple Boot Flag at 0x3a set to 0x1
NTFS driver 2.1.15 [Flags: R/O].
udf: registering filesystem
Initializing Cryptographic API
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
Real Time Clock Driver v1.12
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
pcnet32.c:v1.30i 06.28.2004 tsbogend@alpha.franken.de
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
ACPI: PCI interrupt 0000:00:09.1[A] -> GSI 15 (level, low) -> IRQ 15
Adaptec I2O RAID controller 0 at e0824000 size=100000 irq=15
dpti: If you have a lot of devices this could take a few minutes.
dpti0: Reading the hardware resource table.
TID 008 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001
TID 009 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001
TID 531 Vendor: ADAPTEC Device: RAID-5 Rev: 370F
TID 537 Vendor: ADAPTEC Device: RAID-0 Rev: 370F
scsi0 : Vendor: Adaptec Model: 3200S FW:370F
Vendor: ADAPTEC Model: RAID-5 Rev: 370F
Type: Direct-Access ANSI SCSI revision: 02
Vendor: ADAPTEC Model: RAID-0 Rev: 370F
Type: Direct-Access ANSI SCSI revision: 02
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
aic7892: Ultra160 Wide Channel A, SCSI Id=15, 32/253 SCBs
(scsi1:A:3): 20.000MB/s transfers (20.000MHz, offset 16)
(scsi1:A:6): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
Vendor: TEAC Model: CD-ROM CD-532S Rev: 1.0A
Type: CD-ROM ANSI SCSI revision: 02
Vendor: SEAGATE Model: SX150176LC Rev: BA08
Type: Direct-Access ANSI SCSI revision: 02
scsi1:A:6:0: Tagged Queuing enabled. Depth 8
SCSI device sda: 71131136 512-byte hdwr sectors (36419 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SCSI device sdb: 250904576 512-byte hdwr sectors (128463 MB)
SCSI device sdb: drive cache: write through
sdb: unknown partition table
Attached scsi disk sdb at scsi0, channel 0, id 4, lun 0
SCSI device sdc: 97693755 512-byte hdwr sectors (50019 MB)
SCSI device sdc: drive cache: write through
sdc: sdc1 sdc2 sdc3
Attached scsi disk sdc at scsi1, channel 0, id 6, lun 0
sr0: scsi3-mmc drive: 0x/0x caddy
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 3, lun 0
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 163
i2o: Checking for PCI I2O controllers...
ACPI: PCI interrupt 0000:00:09.1[A] -> GSI 15 (level, low) -> IRQ 15
i2o: I2O controller on bus 0 at 73.
i2o: PCI I2O controller at E0000000 size=33554432
I2O: MTRR workaround for Intel i960 processor
i2o/iop0: Installed at IRQ15
i2o: 1 I2O controller found and installed.
Activating I2O controllers...
This may take a few minutes if there are many devices
dpti: Could Not find task 0 in wait queue
Tasks in wait queue:
i2o_scsi.c: Version 0.1.2
chain_pool: 0 bytes @ c15edd60
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k freed
Adding 995988k swap on /dev/sdc1. Priority:-1 extents:1
EXT3 FS on sdc2, internal journal
0000:03:04.0: DC21143 at 0x9800, h/w address 00:c0:95:e2:b6:44,
and requires IRQ10 (provided by PCI BIOS).
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
0000:03:05.0: DC21143 at 0x9400, h/w address 00:c0:95:e2:b6:45,
and requires IRQ15 (provided by PCI BIOS).
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
0000:03:06.0: DC21143 at 0x9000, h/w address 00:c0:95:e2:b6:46,
and requires IRQ11 (provided by PCI BIOS).
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
0000:03:07.0: DC21143 at 0x8800, h/w address 00:c0:95:e2:b6:47,
and requires IRQ3 (provided by PCI BIOS).
de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: registered device at major 80
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdc3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: media is 100Mb/s.
Und ein LSPCI -v:
hashdb:/# lspci -v
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
(rev 03)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Flags: bus master, medium devsel, latency 8
Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133
AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: de000000-dfcfffff
Prefetchable memory behind bridge: e3f00000-e3ffffff
Capabilities: [80] Power Management version 2
0000:00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 40)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:04.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Flags: medium devsel
I/O ports at d800 [disabled] [size=16]
Capabilities: [c0] Power Management version 2
0000:00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
0000:00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
0000:00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 40)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Flags: medium devsel, IRQ 9
Capabilities: [68] Power Management version 2
0000:00:09.0 PCI bridge: Adaptec (formerly DPT) PCI Bridge (rev 02) (prog-if
00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Capabilities: [68] Power Management version 2
0000:00:09.1 0ebc: Adaptec (formerly DPT) SmartRAID V Controller (rev 02)
(prog-if 03)
Subsystem: Adaptec (formerly DPT) 3000S Ultra3 Dual Channel
Flags: bus master, medium devsel, latency 64, IRQ 15
BIST result: 00
Memory at e0000000 (32-bit, prefetchable) [size=32M]
Capabilities: [80] Power Management version 2
0000:00:0a.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03) (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 00008000-00009fff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfe00000
Capabilities: [dc] Power Management version 1
0000:00:0c.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
BIST result: 00
I/O ports at 7800 [disabled] [size=256]
Memory at db800000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
0000:01:01.0 VGA compatible controller: Trident Microsystems 3DImage 9750
(rev f3) (prog-if 00 [VGA])
Subsystem: Trident Microsystems 3DImage 9750
Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency 64, IRQ
3
Memory at df000000 (32-bit, non-prefetchable) [size=4M]
Memory at de800000 (32-bit, non-prefetchable) [size=128K]
Memory at de000000 (32-bit, non-prefetchable) [size=4M]
Expansion ROM at e3ff0000 [disabled] [size=64K]
0000:03:04.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev 41)
Subsystem: Znyx Advanced Systems: Unknown device 0013
Flags: bus master, medium devsel, latency 96, IRQ 10
I/O ports at 9800 [size=128]
Memory at dd800000 (32-bit, non-prefetchable) [size=1K]
0000:03:05.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev 41)
Subsystem: Znyx Advanced Systems: Unknown device 0013
Flags: bus master, medium devsel, latency 96, IRQ 15
I/O ports at 9400 [size=128]
Memory at dd000000 (32-bit, non-prefetchable) [size=1K]
0000:03:06.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev 41)
Subsystem: Znyx Advanced Systems: Unknown device 0013
Flags: bus master, medium devsel, latency 96, IRQ 11
I/O ports at 9000 [size=128]
Memory at dc800000 (32-bit, non-prefetchable) [size=1K]
0000:03:07.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev 41)
Subsystem: Znyx Advanced Systems: Unknown device 0013
Flags: bus master, medium devsel, latency 96, IRQ 3
I/O ports at 8800 [size=128]
Memory at dc000000 (32-bit, non-prefetchable) [size=1K]
Reply to: