AW: hde wird nicht erkannt
Habe jetzt meinen 2.4er Kernel gebootet.
Auch für den Kernel der config Auszug:
CONFIG_BLK_DEV_PDC202XX_OLD=m
CONFIG_PDC202XX_BURST=y
CONFIG_BLK_DEV_PDC202XX_NEW=m
CONFIG_PDC202XX_FORCE=y
Und hier die dmesg Ausgabe:
Linux version 2.4.27-ct-1 (root@debuild) (gcc version 3.3.4 (Debian
1:3.3.4-13)) #1 Sat Jan 15 16:14:04 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffd000 (usable)
BIOS-e820: 0000000007ffd000 - 0000000007fff000 (ACPI data)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32765
zone(0): 4096 pages.
zone(1): 28669 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 98 and too old
You can enable it with acpi=force
Kernel command line: root=/dev/sda6 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 350.800 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 122952k/131060k available (1242k kernel code, 7716k reserved, 478k
data, 120k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 350.8011 MHz.
..... host bus clock speed is 100.2286 MHz.
cpu: 0, clocks: 1002286, slice: 501143
CPU0<T0:1002272,T1:501120,D:9,S:501143,C:1002286>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xf0750, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:04.0
PCI: Found IRQ 5 for device 00:04.2
PCI: Sharing IRQ 5 with 00:06.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4020 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 4020k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 120k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 5 for device 00:06.0
PCI: Sharing IRQ 5 with 00:04.2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7890/91 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue c7ff3374, I/O limit 4095Mb (mask 0xffffffff)
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
blk: queue c7ff3474, I/O limit 4095Mb (mask 0xffffffff)
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p2 < p5 p6 p7 p8 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 377488k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: WDC WD307AA-00BAA0, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-M1202, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdb: attached ide-cdrom driver.
hdb: ATAPI 32X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.12
hdd: attached ide-cdrom driver.
hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache
hda: attached ide-disk driver.
hda: 60074784 sectors (30758 MB) w/2048KiB Cache, CHS=59598/16/63
/dev/ide/host0/bus0/target0/lun0: p2 p3 < p5 >
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: Found IRQ 11 for device 00:0c.0
eth0: Davicom DM9102 at pci00:0c.0, 00:08:a1:2c:76:fb, irq 11.
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:DMA
PDC20268: IDE controller at PCI slot 00:0a.0
PCI: Found IRQ 10 for device 00:0a.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:pio, hdh:pio
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 16:28:01 Jan 15 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:04.2
PCI: Sharing IRQ 5 with 00:06.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002)
uhci.c: USB Universal Host Controller Interface driver v1.1
Reply to: