hde wird nicht erkannt
Hallo,
Ich habe ein Probelm mit einer nachträglich eingebauten Promise Ultra100TX2.
Die Karte wird zwar erkannt, die an ihr angeschlossene Platte aber nicht.
Auch fdisk /dev/hde sagt "Unable to open /dev/hde"
Allerdings hat ein älteres Knoppix damit überhaupt keine Probleme.
Wie kann ich den Kernel bzw. seine Module konfigurieren, dass beim Booten
auch die Hardware am Ultra100 erkannt wird?
Oder funkt mir da etwas anderes dazwischen? ACPI oder so?
Danke,
Robert
Ausgabe von dmesg
Linux version 2.6.8-2-686 (dilinger@toaster.hq.voxel.net) (gcc version 3.3.5
(Debian 1:3.3.5-6)) #1 Mon Jan 24 03:58:38 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffd000 (usable)
BIOS-e820: 0000000007ffd000 - 0000000007fff000 (ACPI data)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32765
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28669 pages, LIFO batch:6
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
ACPI disabled because your bios is from 98 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: root=/dev/sda6 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 512 (order 9: 4096 bytes)
Detected 350.846 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 121984k/131060k available (1550k kernel code, 8528k reserved, 688k
data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 690.17 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0183fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 350.0739 MHz.
..... host bus clock speed is 100.0211 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4672k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0750, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fd110
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xd140, dseg 0xf0000
pnp: 00:0f: ioport range 0x290-0x297 has been reserved
pnp: 00:0f: ioport range 0xe400-0xe43f has been reserved
pnp: 00:0f: ioport range 0xe800-0xe83f has been reserved
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:04.0
PCI: IRQ 0 for device 0000:00:04.2 doesn't match PIRQ mask - try
pci=usepirqmask
PCI: Found IRQ 5 for device 0000:00:04.2
PCI: Sharing IRQ 5 with 0000:00:06.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4672 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
PCI: Found IRQ 5 for device 0000:00:06.0
PCI: Sharing IRQ 5 with 0000:00:04.2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7890/91 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
Using anticipatory io scheduler
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 8
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p2 < p5 p6 p7 p8 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 377488k swap on /dev/sda5. Priority:-1 extents:1
EXT3 FS on sda6, internal journal
Real Time Clock Driver v1.12
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
Capability LSM initialized
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.100 (c) Dave Jones
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: Found IRQ 11 for device 0000:00:0c.0
eth0: Davicom DM9102 at pci0000:00:0c.0, 00:08:a1:2c:76:fb, irq 11.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 5 for device 0000:00:04.2
PCI: Sharing IRQ 5 with 0000:00:06.0
uhci_hcd 0000:00:04.2: Intel Corp. 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:04.2: irq 5, io base 0000d400
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
inserting floppy driver for 2.6.8-2-686
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: PC Speaker
agpgart: Detected an Intel 440BX Chipset.
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: AGP aperture is 64M @ 0xe4000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
Linux Tulip driver version 1.1.13 (May 11, 2002)
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02ff020(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Reply to: