Re: APIC anstatt XT-PIC auf nem Asus A7V8X mit Via KT400?
Hallo.
Am Donnerstag, 15. Mai 2003 18:59 schrieb Robert Rakowicz:
> > > > So und eigentlich habe ich den Kernel für APIC und ACPI konfiguriert
> > > > und gebacken. Muss ich da noch irgendein Parameter beim Laden des
> > > > Kernel's über Lilo übergeben? Oder geht das mit dem 2.4.19er Kernel
> > > > nicht?
> > >
> > > tja, wenn Du es im BIOS nicht eingestellt hast bzw. nicht einstellen
> > > kannst, hast Du schlechte Karten
> > >
> > > Pozdrawiam/Gruß/Regards
> > > Robert Rakowicz
> >
> > Doch kann ich. Dort steht auch drin, dass die IRQ Verteilung via APIC
> > geschehen soll. Funktionieren tut es aber trotzdem nicht.
> > Unter Wintendo XP geht das ohne Probs :(
>
> hmm, an sich geht es aber schon. Hast Du den Kernel selbst übersetzt
> oder ist das ein *fertiger*? Mit dmesg solltest Du etwas mehr erfahren.
>
> Pozdrawiam/Gruß/Regards
> Robert Rakowicz
Also der Kernel ist selbst gebacken!
Dmesg sagt auch das der APIC aktiviert ist, aber klappen tut es anscheinend
nicht :( Vielleicht noch Jemand ne Idee? Post mal nen Teil der Kernel-Config
und die Ausgabe von Dmesg mit.
Konfiguration des Kernel's (2.4.19):
<schnipp>
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_MCE=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_BIGPHYS_AREA is not set
# CONFIG_SMP is not set
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
</schnapp>
Dmesg ausgabe direkt nach dem starten:
<schnipp>
Linux version 2.4.19 (root@theoracle) (gcc version 3.2.3) #1 Son Mai 11
23:55:03 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fffc000 (usable)
BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
Advanced speculative caching feature present
On node 0 totalpages: 131068
zone(0): 4096 pages.
zone(1): 126972 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux-2.4.19
Found and enabled local APIC!
Initializing CPU#0
Detected 1533.426 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3060.53 BogoMIPS
Memory: 515608k/524272k available (1262k kernel code, 8276k reserved, 302k
data, 292k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
Advanced speculative caching feature present
Disabling advanced speculative caching
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbf7 c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbf7 c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbf7 c1c3fbff 00000000 00000000
CPU: AMD Athlon(TM) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1533.4559 MHz.
..... host bus clock speed is 266.6880 MHz.
cpu: 0, clocks: 2666880, slice: 1333440
CPU0<T0:2666880,T1:1333440,D:0,S:1333440,C:2666880>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf1720, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/3177] at 00:11.0
PCI: Found IRQ 10 for device 00:07.0
PCI: Sharing IRQ 10 with 00:08.0
PCI: Sharing IRQ 10 with 00:0e.0
PCI: Found IRQ 3 for device 00:10.2
IRQ routing conflict for 00:10.0, have irq 9, want irq 3
IRQ routing conflict for 00:10.1, have irq 9, want irq 3
PCI: Sharing IRQ 3 with 00:10.3
PCI: Via IRQ fixup for 00:10.2, from 255 to 3
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI
enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
HPT370A: IDE controller on PCI bus 00 dev 68
PCI: Found IRQ 11 for device 00:0d.0
PCI: Sharing IRQ 11 with 01:00.0
HPT370A: chipset revision 4
HPT370A: not 100% native mode: will probe irqs later
HPT370: using 33MHz PCI clock
ide0: BM-DMA at 0x9400-0x9407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x9408-0x940f, BIOS settings: hdc:DMA, hdd:DMA
VP_IDE: IDE controller on PCI bus 00 dev 89
PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using
pci=biosirq.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, contact Vojtech Pavlik <vojtech@ucw.cz>
hda: IC35L060AVVA07-0, ATA DISK drive
hdb: IC35L060AVVA07-0, ATA DISK drive
hdc: IBM-DTLA-307060, ATA DISK drive
hdd: IBM-DHEA-36481, ATA DISK drive
hde: TOSHIBA DVD-ROM SD-M1502, ATAPI CD/DVD-ROM drive
hdf: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive
hdg: ATAPI-CD ROM-DRIVE-52MAX, ATAPI CD/DVD-ROM drive
ide0 at 0xa800-0xa807,0xa402 on irq 11
ide1 at 0xa000-0xa007,0x9802 on irq 11
ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2: probed IRQ 14 failed, using default.
ide3 at 0x170-0x177,0x376 on irq 15
ide3: probed IRQ 15 failed, using default.
hda: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63, UDMA(100)
hdb: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63, UDMA(100)
hdc: 120103200 sectors (61493 MB) w/1916KiB Cache, CHS=119150/16/63, UDMA(44)
hdd: 12692736 sectors (6499 MB) w/472KiB Cache, CHS=12592/16/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 >
/dev/ide/host0/bus0/target1/lun0: p1
/dev/ide/host0/bus1/target0/lun0: [PTBL] [7476/255/63] p1 p2 < p5 >
/dev/ide/host0/bus1/target1/lun0: [PTBL] [790/255/63] p1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
tg3.c:v0.99 (Jun 11, 2002)
PCI: Enabling device 00:09.0 (0014 -> 0016)
PCI: Assigned IRQ 5 for device 00:09.0
PCI: Sharing IRQ 5 with 00:0f.0
eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit)
10/100/1000BaseT Ethernet 00:e0:18:99:fd:a0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: unsupported bridge
agpgart: no supported devices found.
Creative EMU10K1 PCI Audio Driver, version 0.19, 23:56:20 May 11 2003
PCI: Enabling device 00:0b.0 (0004 -> 0005)
PCI: Assigned IRQ 5 for device 00:0b.0
emu10k1: EMU10K1 rev 7 model 0x8061 found, IO at 0xb400-0xb41f, IRQ 5
ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
emu10k1: SBLive! 5.1 card detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 292k freed
Adding Swap: 119912k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,65), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide1(22,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
spurious 8259A interrupt: IRQ7.
Real Time Clock Driver v1.10e
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack (4095 buckets, 32760 max)
CAPI-driver Rev 1.1.4.1: loaded
capifs: Rev 1.1.4.1
capi20: started up with major 68
kcapi: capi20 attached
capi20: Rev 1.1.4.2: started up with major 68 (middleware+capifs)
b1: revision 1.1.4.1
b1dma: revision 1.1.4.1
b1pci: revision 1.1.4.1
kcapi: driver b1pci attached
b1pciv4: revision 1.1.4.1
kcapi: driver b1pciv4 attached
PCI: Enabling device 00:0f.0 (0004 -> 0007)
PCI: Found IRQ 5 for device 00:0f.0
PCI: Sharing IRQ 5 with 00:09.0
b1pciv4: PCI BIOS reports AVM-B1 V4 at i/o 0x8800, irq 5, mem 0xeb000000
kcapi: Controller 1: b1pciv4-8800 attached
b1pciv4: AVM B1 PCI V4 at i/o 0x8800, irq 5, mem 0xeb000000, revision 4 (dma)
b1pci: 1 B1-PCI card(s) detected
eth0: Link is up at 100 Mbps, full duplex.
eth0: Flow control is off for TX and off for RX.
b1pciv4-8800: card 1 "B1" ready.
b1pciv4-8800: card 1 Protocol: DSS1
b1pciv4-8800: card 1 Linetype: point to multipoint
b1pciv4-8800: B1-card (3.10-02) now active
kcapi: card 1 "b1pciv4-8800" ready.
kcapi: notify up contr 1
capi: controller 1 up
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
kcapi: appl 1 up
kcapi: appl 2 up
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
devfs_mk_dir(isdn): using old entry in dir: dfff25c0 ""
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded
kcapi: capidrv attached
kcapi: appl 3 up
capidrv-1: now up (2 B channels)
capidrv-1: D2 trace enabled
capidrv: Rev 1.1.4.1: loaded
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 00:01:39 May 12 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 3 for device 00:10.0
IRQ routing conflict for 00:10.0, have irq 9, want irq 3
IRQ routing conflict for 00:10.1, have irq 9, want irq 3
PCI: Sharing IRQ 3 with 00:10.2
PCI: Sharing IRQ 3 with 00:10.3
usb-uhci.c: USB UHCI at I/O 0x8400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 3 for device 00:10.1
IRQ routing conflict for 00:10.0, have irq 9, want irq 3
IRQ routing conflict for 00:10.1, have irq 9, want irq 3
PCI: Sharing IRQ 3 with 00:10.2
PCI: Sharing IRQ 3 with 00:10.3
usb-uhci.c: USB UHCI at I/O 0x8000, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 00:10.2 (0014 -> 0015)
PCI: Found IRQ 3 for device 00:10.2
IRQ routing conflict for 00:10.0, have irq 9, want irq 3
IRQ routing conflict for 00:10.1, have irq 9, want irq 3
PCI: Sharing IRQ 3 with 00:10.3
usb-uhci.c: USB UHCI at I/O 0x7800, IRQ 3
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x711/0x230) is not claimed by any active
driver.
hub.c: USB new device connect on bus1/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x67b/0x2303) is not claimed by any active
driver.
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
hub.c: USB new device connect on bus2/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x4b8/0x10c) is not claimed by any active
driver.
usbserial.c: USB Serial support registered for Magic Control Technology
USB-RS232
usbserial.c: USB Serial support registered for MCT/Sitecom USB-RS232
usbserial.c: MCT/Sitecom USB-RS232 converter detected
usbserial.c: MCT/Sitecom USB-RS232 converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: USB Serial support registered for MCT/D-Link DU-H3SP USB BAY
mct_u232.c: v1.1:Magic Control Technology USB-RS232 converter driver
usbserial.c: USB Serial support registered for PL-2303
usbserial.c: PL-2303 converter detected
usbserial.c: PL-2303 converter now attached to ttyUSB1 (or usb/tts/1 for
devfs)
pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.9
hub.c: USB new device connect on bus2/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x4b8/0x5) is not claimed by any active driver.
usb.c: registered new driver usbscanner
scanner.c: 0.4.6:USB Scanner Driver
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid
0x04B8 pid 0x0005
printer.c: v0.11: USB Printer Device Class driver
</schnapp>
Ich hoffe das mir da noch Jemand helfen kann.
Das nervt total mit den IRQ Konflikten.
Im Bios ist die IRQ-Verteilung auf APIC eingestellt.
bye Ingo
Reply to: