Hallo,
ich versuche einen Sedlbauer SpeedFax Pci zu faxen zu bewegen, leider
ohne den gewünschten Erfolg.
System:
Debian 3.0 r1
Kernel 2.4.20
Hylafax 4.1.2
Die Karte läuft ansonsten einwandfrei und der Faxempfang klappt auch
wunderbar, nur das Senden ist ein Problem. Ein Logfile habe ich
beigefuegt.
Vielleicht hat ja jemand einen Tipp für mich.
Gruss
Marco Zwillich
Your facsimile job to 85005 failed because:
Stop and wait failure (modem on hook); Giving up after 3 attempts to
send same page
---- Transcript of session follows ----
May 06 15:13:05.75: [ 1052]: SESSION BEGIN 00000028 49540685005
May 06 15:13:05.75: [ 1052]: HylaFAX (tm) Version 4.1.2
May 06 15:13:05.75: [ 1052]: SEND FAX: JOB 7 DEST 85005 COMMID 00000028
DEVICE '/dev/ttyI0'
May 06 15:13:05.75: [ 1052]: MODEM set DTR OFF
May 06 15:13:05.75: [ 1052]: DELAY 75 ms
May 06 15:13:05.82: [ 1052]: MODEM set DTR ON
May 06 15:13:05.82: [ 1052]: DELAY 2600 ms
May 06 15:13:08.43: [ 1052]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
May 06 15:13:08.43: [ 1052]: MODEM flush i/o
May 06 15:13:08.43: [ 1052]: <-- [4:ATZ\r]
May 06 15:13:08.43: [ 1052]: --> [2:OK]
May 06 15:13:08.43: [ 1052]: DELAY 3000 ms
May 06 15:13:11.43: [ 1052]: <-- [10:AT&E85006\r]
May 06 15:13:11.44: [ 1052]: --> [9:AT&E85006]
May 06 15:13:11.44: [ 1052]: --> [2:OK]
May 06 15:13:11.44: [ 1052]: <-- [5:ATE0\r]
May 06 15:13:11.45: [ 1052]: --> [4:ATE0]
May 06 15:13:11.45: [ 1052]: --> [2:OK]
May 06 15:13:11.45: [ 1052]: <-- [5:ATV1\r]
May 06 15:13:11.46: [ 1052]: --> [2:OK]
May 06 15:13:11.46: [ 1052]: <-- [5:ATQ0\r]
May 06 15:13:11.47: [ 1052]: --> [2:OK]
May 06 15:13:11.47: [ 1052]: <-- [7:ATS0=0\r]
May 06 15:13:11.48: [ 1052]: --> [2:OK]
May 06 15:13:11.48: [ 1052]: <-- [7:ATS8=2\r]
May 06 15:13:11.49: [ 1052]: --> [2:OK]
May 06 15:13:11.49: [ 1052]: <-- [8:ATS7=60\r]
May 06 15:13:11.50: [ 1052]: --> [2:OK]
May 06 15:13:11.50: [ 1052]: <-- [12:AT+FCLASS=1\r]
May 06 15:13:11.51: [ 1052]: --> [2:OK]
May 06 15:13:11.51: [ 1052]: <-- [5:ATM0\r]
May 06 15:13:11.52: [ 1052]: --> [2:OK]
May 06 15:13:11.52: [ 1052]: MODEM input buffering enabled
May 06 15:13:11.53: [ 1052]: <-- [12:AT+FCLASS=1\r]
May 06 15:13:11.63: [ 1052]: --> [2:OK]
May 06 15:13:11.63: [ 1052]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
May 06 15:13:11.64: [ 1052]: DIAL 85005
May 06 15:13:11.64: [ 1052]: <-- [10:ATDT85005\r]
May 06 15:13:16.76: [ 1052]: --> [7:CONNECT]
May 06 15:13:16.77: [ 1052]: MODEM input buffering disabled
May 06 15:13:19.01: [ 1052]: --> [2:OK]
May 06 15:13:19.01: [ 1052]: REMOTE CSI "Marco Zwillich"
May 06 15:13:19.01: [ 1052]: <-- [9:AT+FRH=3\r]
May 06 15:13:19.02: [ 1052]: --> [7:CONNECT]
May 06 15:13:19.37: [ 1052]: --> [2:OK]
May 06 15:13:19.37: [ 1052]: REMOTE best rate 14400 bit/s
May 06 15:13:19.37: [ 1052]: REMOTE max page width 2432 pixels in 303 mm
May 06 15:13:19.37: [ 1052]: REMOTE max unlimited page length
May 06 15:13:19.38: [ 1052]: REMOTE best vres 7.7 line/mm
May 06 15:13:19.38: [ 1052]: REMOTE best format 2-D MR
May 06 15:13:19.38: [ 1052]: REMOTE best 0 ms/scanline
May 06 15:13:19.38: [ 1052]: USE 14400 bit/s
May 06 15:13:19.38: [ 1052]: USE 0 ms/scanline
May 06 15:13:19.38: [ 1052]: SEND file "docq/doc7.tif;00"
May 06 15:13:19.38: [ 1052]: USE page width 1728 pixels in 215 mm
May 06 15:13:19.38: [ 1052]: USE unlimited page length
May 06 15:13:19.38: [ 1052]: USE 3.85 line/mm
May 06 15:13:19.38: [ 1052]: USE 1-D MR
May 06 15:13:19.38: [ 1052]: SEND training at v.17 14400 bit/s
May 06 15:13:19.38: [ 1052]: <-- [9:AT+FTH=3\r]
May 06 15:13:21.13: [ 1052]: --> [7:CONNECT]
May 06 15:13:21.16: [ 1052]: --> [7:CONNECT]
May 06 15:13:22.15: [ 1052]: --> [2:OK]
May 06 15:13:22.15: [ 1052]: <-- [9:AT+FTS=7\r]
May 06 15:13:22.16: [ 1052]: --> [5:ERROR]
May 06 15:13:22.16: [ 1052]: MODEM Command error
May 06 15:13:22.17: [ 1052]: SEND: Stop and wait failure (modem on
hook); Giving up after 3 attempts to send same page "docq/doc7.tif;00",
dirnum 0
May 06 15:13:22.17: [ 1052]: <-- [9:AT+FTH=3\r]
May 06 15:13:23.79: [ 1052]: --> [7:CONNECT]
May 06 15:13:24.05: [ 1052]: --> [2:OK]
May 06 15:13:24.05: [ 1052]: MODEM input buffering enabled
May 06 15:13:24.05: [ 1052]: <-- [5:ATH0\r]
May 06 15:13:24.16: [ 1052]: --> [10:NO CARRIER]
May 06 15:13:24.16: [ 1052]: MODEM No carrier
May 06 15:13:24.16: [ 1052]: MODEM set DTR OFF
May 06 15:13:24.17: [ 1052]: SESSION END
---- Unsent job status ----
Destination: 85005
JobID: 7
GroupID: 7
Sender: root
Mailaddr: zwillich@server.zwillich.netz
CommID: 00000028
Submitted From: desktop.zwillich.netz
Page Width: 210 (mm)
Page Length: 297 (mm)
Resolution: 98 (lpi)
Status: Stop and wait failure (modem on hook); Giving up after 3
attempts to send same page
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 3 (total phone calls placed)
Pages: 0 (pages transmitted)
TotPages: 1 (total pages to transmit)
Attempts: 3 (attempts to send current page)
Dirnum: 0 (directory of next page to send)
---- Documents submitted for transmission ----
The following documents were submitted for transmission and are
available on the server for reuse until they are automatically
purged when this job is removed. Documents may also be manually
removed using the faxrm command; consult faxrm(1) for information.
Filename Size Type
docq/doc7.tif 0 TIFF