SuperTrak100 und normale IDE
Hallo,
wie kann ich in Woody einen Promise SuperTrak 100
mit 4 Platten (Raid1+0) einbinden?
Ich habe i2o_block als Module geladen, aber irgendwie scheint
es ein Problem zwischen der Platte /dev/hda und dem Controller
zu geben (siehe unten bei dmseg).
Ich weiss nicht so recht weiter und alle HowTos, die ich gefunden
habe gehen von einem Raid und aus.
Was muss ich jetzt wohin linken bzw. wo finde ich die Platte?
Vielen Dank
Daniel
---------------------------------------------------------------
# dmesg
ide: Found promise 20265 in RAID mode.
ide: Skipping Promise PDC20265 attached to I2O RAID controller.
hda: ST320011A, ATA DISK drive
hdc: CD-ROM CCD-52X6S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [2434/255/63] p1 p2 p3
cramfs: wrong magic
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=2
Freeing unused kernel memory: 212k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 248996k swap-space (priority -1)
Real Time Clock Driver v1.10e
PCI: Found IRQ 10 for device 02:0b.0
PCI: Sharing IRQ 10 with 00:1f.4
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
02:0b.0: 3Com PCI 3c905C Tornado at 0xd880. Vers LK1.1.16
Linux I2O PCI support (c) 1999 Red Hat Software.
I2O Core - (C) Copyright 1999 Red Hat Software
i2o: Checking for PCI I2O controllers...
PCI: Found IRQ 9 for device 02:0d.1
i2o: I2O controller on bus 2 at 105.
i2o: PCI I2O controller at 0xF4000000 size=4194304
I2O: Promise workarounds activated.
I2O: MTRR workaround for Intel i960 processor
i2o/iop0: Installed at IRQ9
i2o: 1 I2O controller found and installed.
I2O: Event thread created as pid 59
Activating I2O controllers...
This may take a few minutes if there are many devices
i2o/iop0: Reset rejected, trying to clear
i2o/iop0: LCT has 8 entries.
i2o/iop0: Configuration dialog desired.
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: registered device at major 80
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
i2ob: Installing tid 14 device at unit 0
i2o/hda: Max segments 8, queue depth 4, byte limit 6144.
i2o/hda: Type 60: 190792MB, 512 byte sectors.
i2o/hda: Maximum sectors/read set to 32.
i2o/hda: unknown partition table
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
SCSI subsystem driver Revision: 1.00
----------------------------------------------------------------
lsmod (Ausschnitt)
sd_mod 10556 0 (autoclean) (unused)
scsi_mod 84984 1 (autoclean) [sd_mod]
ataraid 6400 0 (unused)
i2o_config 6984 0 (unused)
i2o_proc 40480 0 (unused)
i2o_block 33888 0 (unused)
i2o_core 40800 0 [i2o_config i2o_proc i2o_block]
i2o_pci 2884 1 [i2o_core]
3c59x 24936 1
Reply to: