[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Sedlbauer Speedfax+ und Hylafax

Hallo zusammen,

ich bemühe mich seit längerer zeit darum, Sedlbauer Speedfax+ und
Hylafax zum Laufen zu bringen.

Der Faxempfang scheint zu funktionieren.

Beim Versandversuch erhalten Meldungen, wie diese angehängt per Mail.

Kann mir jemand sagen, was dort schief läuft? Die Konfiguration wurde
mir von der Fa. Seldbauer zur Verfügung gestellt, dennoch scheint es
Probleme mit dem AT+FTS=7 zu geben...

Vielen Dank!

Michael Hierweck
--- Begin Message --- 
Your facsimile job to 02314650137 was not sent because:
    Stop and wait failure (modem on hook)

The job will be retried at 11:29.

    ---- Transcript of session follows ----

May 27 11:28:29.32: [10882]: SESSION BEGIN 00000089 492314650137
May 27 11:28:29.32: [10882]: HylaFAX (tm) Version 4.1.1
May 27 11:28:29.45: [10882]: SEND FAX: JOB 14 DEST 02314650137 COMMID 00000089 DEVICE '/dev/ttyI0'
May 27 11:28:29.45: [10882]: MODEM set DTR OFF
May 27 11:28:29.45: [10882]: DELAY 75 ms
May 27 11:28:29.53: [10882]: MODEM set DTR ON
May 27 11:28:29.53: [10882]: DELAY 2600 ms
May 27 11:28:32.13: [10882]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
May 27 11:28:32.13: [10882]: MODEM flush i/o
May 27 11:28:32.14: [10882]: <-- [4:ATZ\r]
May 27 11:28:32.14: [10882]: --> [2:OK]
May 27 11:28:32.14: [10882]: DELAY 3000 ms
May 27 11:28:35.14: [10882]: <-- [12:AT&E9698472\r]
May 27 11:28:35.15: [10882]: --> [11:AT&E9698472]
May 27 11:28:35.15: [10882]: --> [2:OK]
May 27 11:28:35.15: [10882]: <-- [5:ATE0\r]
May 27 11:28:35.16: [10882]: --> [4:ATE0]
May 27 11:28:35.16: [10882]: --> [2:OK]
May 27 11:28:35.16: [10882]: <-- [5:ATV1\r]
May 27 11:28:35.17: [10882]: --> [2:OK]
May 27 11:28:35.17: [10882]: <-- [5:ATQ0\r]
May 27 11:28:35.18: [10882]: --> [2:OK]
May 27 11:28:35.18: [10882]: <-- [7:ATS0=0\r]
May 27 11:28:35.19: [10882]: --> [2:OK]
May 27 11:28:35.19: [10882]: <-- [7:ATS8=2\r]
May 27 11:28:35.20: [10882]: --> [2:OK]
May 27 11:28:35.20: [10882]: <-- [8:ATS7=60\r]
May 27 11:28:35.21: [10882]: --> [2:OK]
May 27 11:28:35.21: [10882]: <-- [12:AT+FCLASS=1\r]
May 27 11:28:35.22: [10882]: --> [2:OK]
May 27 11:28:35.22: [10882]: <-- [5:ATM0\r]
May 27 11:28:35.23: [10882]: --> [2:OK]
May 27 11:28:35.23: [10882]: MODEM input buffering enabled
May 27 11:28:35.24: [10882]: <-- [12:AT+FCLASS=1\r]
May 27 11:28:35.34: [10882]: --> [2:OK]
May 27 11:28:35.34: [10882]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
May 27 11:28:35.47: [10882]: DIAL 02314650137
May 27 11:28:35.47: [10882]: <-- [16:ATDT02314650137\r]
May 27 11:28:47.94: [10882]: --> [7:CONNECT]
May 27 11:28:47.95: [10882]: MODEM input buffering disabled
May 27 11:28:49.21: [10882]: --> [2:OK]
May 27 11:28:49.21: [10882]: REMOTE NSF "00 00 56 55 55 00 8C 90 80 C1 02 5A"
May 27 11:28:49.21: [10882]: NSF remote fax equipment: Brother 
May 27 11:28:49.21: [10882]: <-- [9:AT+FRH=3\r]
May 27 11:28:49.21: [10882]: --> [7:CONNECT]
May 27 11:28:49.91: [10882]: --> [2:OK]
May 27 11:28:49.91: [10882]: REMOTE CSI "+49 231 4650137"
May 27 11:28:49.91: [10882]: <-- [9:AT+FRH=3\r]
May 27 11:28:49.91: [10882]: --> [7:CONNECT]
May 27 11:28:50.35: [10882]: --> [2:OK]
May 27 11:28:50.35: [10882]: REMOTE best rate 14400 bit/s
May 27 11:28:50.35: [10882]: REMOTE max page width 1728 pixels in 215 mm
May 27 11:28:50.35: [10882]: REMOTE max unlimited page length 
May 27 11:28:50.35: [10882]: REMOTE best vres 7.7 line/mm
May 27 11:28:50.35: [10882]: REMOTE best format 2-D MMR
May 27 11:28:50.35: [10882]: REMOTE supports T.30 Annex A, ECM
May 27 11:28:50.35: [10882]: REMOTE best 0 ms/scanline
May 27 11:28:50.35: [10882]: USE 14400 bit/s
May 27 11:28:50.35: [10882]: USE 0 ms/scanline
May 27 11:28:50.35: [10882]: SEND file "docq/doc14.cover;00"
May 27 11:28:50.35: [10882]: USE page width 1728 pixels in 215 mm
May 27 11:28:50.35: [10882]: USE unlimited page length 
May 27 11:28:50.36: [10882]: USE 3.85 line/mm
May 27 11:28:50.36: [10882]: USE 1-D MR
May 27 11:28:50.36: [10882]: SEND training at v.17 14400 bit/s
May 27 11:28:50.36: [10882]: <-- [9:AT+FTH=3\r]
May 27 11:28:52.16: [10882]: --> [7:CONNECT]
May 27 11:28:52.20: [10882]: --> [7:CONNECT]
May 27 11:28:53.21: [10882]: --> [2:OK]
May 27 11:28:53.21: [10882]: <-- [9:AT+FTS=7\r]
May 27 11:28:53.22: [10882]: --> [5:ERROR]
May 27 11:28:53.22: [10882]: MODEM Command error
May 27 11:28:53.22: [10882]: <-- [9:AT+FTH=3\r]
May 27 11:28:54.85: [10882]: --> [7:CONNECT]
May 27 11:28:55.09: [10882]: --> [2:OK]
May 27 11:28:55.09: [10882]: MODEM input buffering enabled
May 27 11:28:55.09: [10882]: <-- [5:ATH0\r]
May 27 11:28:55.21: [10882]: --> [10:NO CARRIER]
May 27 11:28:55.21: [10882]: MODEM No carrier
May 27 11:28:55.21: [10882]: MODEM set DTR OFF
May 27 11:28:55.21: [10882]: SESSION END

--- End Message ---

Attachment: signature.asc
Description: This is a digitally signed message part

Reply to: