Re: woody als t-dsl-router
Hallo!
also hier die Ausgaben nach der Einwahl:
route -n sagt nun:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
217.5.98.173 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0
und ifconfig:
eth0 Link encap:Ethernet HWaddr 00:60:97:80:3F:81
inet addr:192.168.100.100 Bcast:192.168.100.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:17 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:846 (846.0 b) TX bytes:643 (643.0 b)
Interrupt:10 Base address:0x300
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:85 (85.0 b) TX bytes:85 (85.0 b)
ppp0 Link encap:Point-to-Point Protocol
inet addr:217.232.150.224 P-t-P:217.5.98.173
Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
RX bytes:366 (366.0 b) TX bytes:392 (392.0 b)
und in meiner /etc/network/interfaces steht:
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface
# automatically added when upgrading
auto lo
iface lo inet loopback
# The first network card - this entry was created during the Debian
installation
# (network, broadcast and gateway are optional)
# automatically added when upgrading
auto eth0
iface eth0 inet static
address 192.168.100.100
netmask 255.255.255.0
network 192.168.100.0
broadcast 192.168.100.255
gateway 192.168.100.1
iface eth1 inet static
address 192.168.100.1
netmask 255.255.255.0
network 192.168.100.0
broadcast 192.168.100.255
gateway 192.168.100.1
ich sehe, dass es in meiner ifconfig Ausgabe heisst, das ppp0 device hätte
die Maske 255.255.255.255, sollte die nicht 0.0.0.0 sein?
Grüße
manuel
> Hi,
>
> > Kernel IP routing table
> > Destination Gateway Genmask Flags Metric Ref Use
> > Iface
> > 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0
> e
> th0
> > 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0
> e
> th0
>
> mach' bitte das route -n noch mal _nach_ der Einwahl.
>
> > und ein ifconfig:
> >
> > eth0 Link encap:Ethernet HWaddr 00:60:97:80:3F:81
> > inet addr:192.168.100.100 Bcast:192.168.100.255
> > Mask:255.255.255.0
> > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:100
> > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> > Interrupt:10 Base address:0x300
> >
> > lo Link encap:Local Loopback
> > inet addr:127.0.0.1 Mask:255.0.0.0
> > UP LOOPBACK RUNNING MTU:3924 Metric:1
> > RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:0
> > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>
> hier fehlt auch noch etwas, das ppp0 device.
> Lass mal das ifconfig ebenfalls nach der Einwahl laufen!
>
> > meine eth1 is anscheinend nicht dauerhaft eingebunden. :(
> > das kernel-modul für meine 2. netzwerkkarte is aber geladen.
>
> Deshalb wäre deine /etc/network/interfaces auch noch ganz hilfreich.
>
>
> Gruß
> --
> Valentin Funk, Stuttgart, <lists4funk@kleinhohenheim.de>
>
--
GMX - Die Kommunikationsplattform im Internet.
http://www.gmx.net
--
Zum AUSTRAGEN schicken Sie eine Mail an debian-user-german-request@lists.debian.org
mit dem Subject "unsubscribe". Probleme? Mail an listmaster@lists.debian.org (engl)
Reply to: