Montage disque en USB 3.0 [aptosid]
Bonjour à tous,
une petite question pas cruciale mais cela me ferait gagner du temps
si je pouvais fluidifier mes backups mobiles sur 1 disque 1To USB 3.0
Samsung
Il marche très bien en USB 2.0 mais je viens d'essayer de le monter en
USB 3.0 et je ne vois rien dans les logs qui me prouve que cela
fonctionne...
La carte expresscard USB 3.0 marche bien elle , les logs du kernel le
prouvent....
Je suis en aptosid avec un kernel très récent
root@aptosidbox:/home/romje# lspci |grep -i USB
00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset
USB2 Enhanced Host Controller (rev 06)
00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset
USB2 Enhanced Host Controller (rev 06)
05:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host
Controller (rev 03)
root@aptosidbox:/home/romje# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip
Fingerprint Sensor
Bus 003 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller
Bus 003 Device 005: ID 17ef:4816 Lenovo
Bus 004 Device 003: ID 05c6:9204 Qualcomm, Inc.
extrait d'une sortie dmesg:
[ 802.689709] xhci_hcd 0000:05:00.0: PME# disabled
[ 802.689736] xhci_hcd 0000:05:00.0: setting latency timer to 64
[ 802.715119] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 802.726033] ehci_hcd 0000:00:1a.0: BAR 0: set to [mem
0xf2728000-0xf27283ff] (PCI address [0xf2728000-0xf27283ff])
[ 802.726044] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 802.726068] ehci_hcd 0000:00:1a.0: restoring config space at offset
0xf (was 0x400, writing 0x40b)
[ 802.726098] ehci_hcd 0000:00:1a.0: restoring config space at offset
0x1 (was 0x2900000, writing 0x2900102)
[ 802.726134] ehci_hcd 0000:00:1a.0: PME# disabled
[ 802.726142] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 802.726149] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 802.726162] ehci_hcd 0000:00:1a.0: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 802.726173] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 802.748439] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 802.758898] ehci_hcd 0000:00:1d.0: BAR 0: set to [mem
0xf2728400-0xf27287ff] (PCI address [0xf2728400-0xf27287ff])
[ 802.758909] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 802.758932] ehci_hcd 0000:00:1d.0: restoring config space at offset
0xf (was 0x400, writing 0x40b)
[ 802.758962] ehci_hcd 0000:00:1d.0: restoring config space at offset
0x1 (was 0x2900000, writing 0x2900102)
[ 802.759001] ehci_hcd 0000:00:1d.0: PME# disabled
[ 802.759010] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 802.759017] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 802.759028] ehci_hcd 0000:00:1d.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 802.759038] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 804.930058] xhci_hcd 0000:05:00.0: PME# enabled
[ 807.324607] xhci_hcd 0000:05:00.0: PME# disabled
[ 807.324631] xhci_hcd 0000:05:00.0: setting latency timer to 64
[ 809.915125] xhci_hcd 0000:05:00.0: PME# enabled
[ 813.929992] ehci_hcd 0000:00:1a.0: PCI INT D disabled
[ 813.930050] ehci_hcd 0000:00:1a.0: PME# enabled
[ 813.937893] ehci_hcd 0000:00:1d.0: PCI INT D disabled
[ 813.937949] ehci_hcd 0000:00:1d.0: PME# enabled
[ 813.940952] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D3
[ 813.948928] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D3
[ 908.483048] xhci_hcd 0000:05:00.0: PME# disabled
[ 908.483071] xhci_hcd 0000:05:00.0: setting latency timer to 64
[ 908.505248] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 908.515819] ehci_hcd 0000:00:1a.0: BAR 0: set to [mem
0xf2728000-0xf27283ff] (PCI address [0xf2728000-0xf27283ff])
[ 908.515831] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 908.515854] ehci_hcd 0000:00:1a.0: restoring config space at offset
0xf (was 0x400, writing 0x40b)
[ 908.515885] ehci_hcd 0000:00:1a.0: restoring config space at offset
0x1 (was 0x2900000, writing 0x2900102)
[ 908.515919] ehci_hcd 0000:00:1a.0: PME# disabled
[ 908.515927] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 908.515934] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D0
[ 908.515947] ehci_hcd 0000:00:1a.0: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 908.515958] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 908.536102] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 908.546746] ehci_hcd 0000:00:1d.0: BAR 0: set to [mem
0xf2728400-0xf27287ff] (PCI address [0xf2728400-0xf27287ff])
[ 908.546758] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 908.546782] ehci_hcd 0000:00:1d.0: restoring config space at offset
0xf (was 0x400, writing 0x40b)
[ 908.546812] ehci_hcd 0000:00:1d.0: restoring config space at offset
0x1 (was 0x2900000, writing 0x2900102)
[ 908.546849] ehci_hcd 0000:00:1d.0: PME# disabled
[ 908.546857] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 908.546865] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 908.546876] ehci_hcd 0000:00:1d.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 908.546886] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 910.663637] xhci_hcd 0000:05:00.0: PME# enabled
[ 914.787176] ehci_hcd 0000:00:1a.0: PCI INT D disabled
[ 914.787234] ehci_hcd 0000:00:1a.0: PME# enabled
[ 914.798131] ehci_hcd 0000:00:1a.0: power state changed by ACPI to D3
[ 914.831064] ehci_hcd 0000:00:1d.0: PCI INT D disabled
[ 914.831114] ehci_hcd 0000:00:1d.0: PME# enabled
[ 914.841998] ehci_hcd 0000:00:1d.0: power state changed by ACPI to D3
les entrées en xhci_hcd sont bien celles concernées par l'usb 3.0 ?
mon disque USB contient un volume group LVM2 (peut etre pas une bonne
idée mais il y est lol)
vgscan ne voit rien ....
je précise que le disque semble bien branché et tourne , il est
convenablement alimenté...
Avez vous des pistes pour débloquer la situation ?
Google n'a pas été trop mon ami sur le coup....
merci par avance
Jerome
J.MOLIERE - Mentor/J
auteur Eyrolles
blog: http://romjethoughts.blogspot.com
Reply to: