Problèmes de démarrage sur carte Geode entre 2.6.17 et 2.6.18
Bonjour,
Sur une carte de type WAFER-LX800 (Geoge à 500Mhz avec 128Mo de Ram),
j'ai installé via un cd net-install une version etch avec un noyau dans
la famille des 2.6.17 => pas de Pb cela fonctionne.
Lorsque je la bascule sur un noyau de type lenny 2.6.18-4 (via un
apt-get dist-upgrade), au démarrage suivant la carte se gèle juste après
GRUB avec comme dernier message :
sauve default
Avec le 2.6.17 pas de Pb le démarrage continu.
Là je sèche...
Merci du coup de main.
Yann.
Ref :
La carte cpu http://www.aplus-sa.com/datasht/WAFER-LX.pdf
Un dmesg lorsque cela fonctionne
------------DMESG ---------------
Linux version 2.6.17-2-486 (Debian 2.6.17-9) (waldi@debian.org) (gcc
version 4.1.2 20060901 (prerelease) (Debian 4.1.1-13)) #1 Wed Sep 13
15:56:30 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000077c0000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
119MB LOWMEM available.
On node 0 totalpages: 30656
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 26560 pages, LIFO batch:7
DMI 2.2 present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 10000000 (gap: 077c0000:f8830000)
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro
No local APIC present or hardware disabled
mapped APIC to ffffd000 (010f1000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 498.139 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 114332k/122624k available (1456k kernel code, 7732k reserved,
566k data, 252k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay using timer specific routine.. 998.36 BogoMIPS
(lpj=1996722)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0088a93d c0c0a13d 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0088a93d c0c0a13d 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 128K (32 bytes/line)
CPU: After all inits, caps: 0088a93d c0c0a13d 00000000 00000000 00000000
00000000 00000000
CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
checking if image is initramfs... it is
Freeing initrd memory: 4136k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfa930, last bus=0
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xb00fb2c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb2f0, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:01.1
PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1183138036.620:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
Freeing unused kernel memory: 252k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
AMD5536: IDE controller at PCI slot 0000:00:0f.2
AMD5536: chipset revision 1
AMD5536: not 100% native mode: will probe irqs later
AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:DMA
Probing IDE interface ide0...
SCSI subsystem initialized
8139too Fast Ethernet driver 0.9.27
usbcore: registered new driver usbfs
usbcore: registered new driver hub
libata version 1.20 loaded.
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
hdb: LTN485S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
eth0: RealTek RTL8139 at 0xf400, 00:08:9b:69:c7:f0, IRQ 5
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth1: RealTek RTL8139 at 0xf600, 00:08:9b:69:c7:ef, IRQ 10
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
sata_uli 0000:00:11.0: version 0.5
ata1: SATA max UDMA/133 cmd 0xFD00 ctl 0xFC02 bmdma 0xF900 irq 11
ata2: SATA max UDMA/133 cmd 0xFB00 ctl 0xFA02 bmdma 0xF908 irq 11
hdb: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763
88:407f
ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_uli
ata2: SATA link down (SStatus 0)
scsi1 : sata_uli
Vendor: ATA Model: HDS728080PLA380 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 05
PCI: Setting latency timer of device 0000:00:0f.5 to 64
ehci_hcd 0000:00:0f.5: EHCI Host Controller
ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0f.5: irq 9, io mem 0xefffd000
ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
PCI: Setting latency timer of device 0000:00:0f.4 to 64
ohci_hcd 0000:00:0f.4: OHCI Host Controller
ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0f.4: irq 9, io mem 0xefffe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0f: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:10: ttyS2 at I/O 0x3e8 (irq = 5) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
PCI: Setting latency timer of device 0000:00:0f.3 to 64
hw_random hardware driver 1.0.0 loaded
Real Time Clock Driver v1.12ac
EXT3 FS on sda1, internal journal
loop: loaded (max 8 devices)
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
ohci_hcd 0000:00:0f.4: wakeup
usb 2-1: new full speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
i2c /dev entries driver
------------/DMESG---------------
Reply to: