Je désespère d'avoir du son :-(
Bonjour à tous et tous mes voeux :-)
Comme indiqué dans le sujet, je désespère d'avoir du son sur mon portable...
J'ai essayé tout plein de remèdes : méthode alsa-project.org,
installation de discover udev (suggéré sur la liste alsa-user), rien n'y
fait.
Sous Win2000, j'ai un très bon son mais j'ai remarqué quelque chose :
l'IRQ 11 semble partagée entre le codec son Ac'97 et l'IEEE 1394 et je
me demande si, au cours de l'installation de la Sarge, je n'ai pas vu un
message du type disabling IRQ 11.
Quelqu'un aurait-il une piste ?
Je suis sous Sarge, noyau 2.6.9 et j'utilise Gnome.
Merci d'avance !
Guillaume
lspci donne :
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97
Audio Controller (rev 02)
lsmod donne :
snd_intel8x0m 17492 4
snd_ac97_codec 65248 2 snd_intel8x0,snd_intel8x0m
snd_pcm_oss 48040 1
snd_mixer_oss 17408 2 snd_pcm_oss
snd_pcm 85640 4
snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_oss
snd_timer 23300 1 snd_pcm
snd 52196 13
snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
snd_page_alloc 9736 3 snd_intel8x0,snd_intel8x0m,snd_pcm
dmesg donne (j'ai tout copié, je ne sais pas trop ce qui pourrait être
utile !)
>EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:09.0 [1558:8880]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:09.0, mfunc 0x01001c00, devctl 0x66
Yenta: ISA IRQ mask 0x0098, PCI irq 10
Socket status: 30000006
ACPI: PCI interrupt 0000:02:09.1[B] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:09.1 [1558:8880]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:09.1, mfunc 0x01001c00, devctl 0x66
Yenta: ISA IRQ mask 0x0098, PCI irq 11
Socket status: 30000006
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:02:05.2[C] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:02:05.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:02:05.2: irq 10, pci mem f8934000
ehci_hcd 0000:02:05.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:05.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usb 1-4: new high speed USB device using address 2
hub 1-4:1.0: USB hub found
hub 1-4:1.0: 4 ports detected
usb 1-4.1: new low speed USB device using address 3
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.0: Intel Corp. 82801CA/CAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 10, io base 0000e000
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. 82801CA/CAM USB (Hub #2)
usb 1-4.4: new high speed USB device using address 4
hub 1-4.4:1.0: USB hub found
hub 1-4.4:1.0: 4 ports detected
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 0000e120
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:02:05.2-4.1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.2: Intel Corp. 82801CA/CAM USB (Hub #3)
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 10, io base 0000e240
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:02:05.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:02:05.0: irq 10, io base 0000a000
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
uhci_hcd 0000:02:05.0: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:02:05.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:02:05.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:02:05.1: irq 11, io base 0000a120
uhci_hcd 0000:02:05.1: new USB bus registered, assigned bus number 6
usb 1-4.4.4: new full speed USB device using address 5
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 1-4.4.4: device descriptor read/all, error -71
usb 1-4.4.4: new full speed USB device using address 6
usb 1-4.4.4: device descriptor read/all, error -71
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11]
MMIO=[d0000800-d0000fff] Max Packet=[2048]
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xa400, 00:90:f5:0d:18:5a, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090f501000d185a]
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.6 to 64
Real Time Clock Driver v1.12
input: PC Speaker
Synaptics Touchpad, model: 1
Firmware: 5.6
180 degree mounted touchpad
Sensor: 18
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
inserting floppy driver for 2.6.9
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP]
irda_init()
NET: Registered protocol family 23
agpgart: Detected an Intel i845 Chipset.
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 64M @ 0xa0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
hw_random hardware driver 1.0.0 loaded
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49383 usecs
intel8x0: clocking to 48000
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03221e0(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 24
ip_tables: (C) 2000-2002 Netfilter core team
cs: IO port probe 0x0100-0x04ff: excluding 0x110-0x117
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
eth0: no IPv6 routers present
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies
Inc Radeon R250 Lf [Radeon Mobility 9000 M9]
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R200 Microcode
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x301300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 300 bytes per conntrack
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300300]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:402:
codec_semaphore: semaphore is not ready [0x1][0x300304]
ALSA /usr/src/alsa/alsa-driver-1.0.7/alsa-kernel/pci/intel8x0m.c:417:
codec_write 1: semaphore is not ready for register 0x54
Reply to: