Re: DriveReady SeekComplete Error
Ben il est sur deuxieme disque ide sur une carte pci ata133 Promise
donc hde/hdf, le pc est ancien.
hde c'est le systeme et je contais mettre les data sur hdf
lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3]
(rev 04)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
MVP3/Pro133x AGP]
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA
[Apollo VP] (rev 41)
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 02)
0000:00:07.3 Host bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
0000:00:12.0 Ethernet controller: National Semiconductor Corporation
DP83815 (MacPhyter) Ethernet Controller
0000:00:14.0 Unknown mass storage controller: Promise Technology, Inc.
20269 (rev 02)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV15
[GeForce2 GTS/Pro] (rev a4)
sudo hdparm /dev/hdf
Password:
/dev/hdf:
multcount = 0 (off)
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 65535/16/63, sectors = 240121728, start = 0
sudo hdparm -I /dev/hdf
/dev/hdf:
ATA device, with non-removable media
Model Number: Maxtor 6Y120P0
Serial Number: Y33VAM6E
Firmware Revision: YAR41BW0
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 240121728
device size with M = 1024*1024: 117246 MBytes
device size with M = 1000*1000: 122942 MBytes (122 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 1 determined by the jumper
Checksum: correct
Georges
Jean-Luc Coulon (f5ibh) wrote:
Je vois hdf... Je pense donc qu'il se trouve sur un contrôleur raid ?
Si oui, quel est le type du contrôleur et le driver utilisé ?
Quel est le mode dma actif du disque ? (hdparm /dev/hdf et hdparm -I
/dev/hdf)
--
- Jean-Luc
Reply to: