Re: Debian Vs Gentoo
je suis abonné merci.
Rolland wrote:
Slut
j´ai essayé la methode de Justice pour pouvoir faire coahbiter gentoo et
deban mais ca ne maeche pas(quand je monte les fichiers de gentoo tout est
corect je chroot meme dans l´environnement gentoo et tout fonctionne
normalement mais au monent du botage je choisis gentoo mais ca ne demare
pas) ..
j´ai meme changé mon fichier /etc/fstab étant donné que mon disque boot
pour genntoo est sur une autre partition voila à quoi resemble mon fdick
/dev/hdb
Device Boot Start End Blocks Id System
/dev/hdb1 * 1 14 105808+ 83 Linux //Patition de
bootage
/dev/hdb2 15 81 506520 82 Linux swap //swap
/dev/hdb3 82 3876 28690200 83 Linux // Linux Racine
et voila à quoi resemble mon /etc/fstab
la partition de boot (hdb1) aurait été plus judicieusment placé en hda1,
m'enfin.
# /etc/fstab: static file system information.
## <file system> <mount point> <type> <options> <dump> <pass>
/dev/hda1 / ext2 errors=remount-ro 0 1
/dev/hda2 none swap sw 0 0
proc /proc proc defaults 0 0
/dev/fd0 /floppy auto user,noauto 0 0
/dev/hdc /cdrom iso9660 ro,user,noauto 0 0
sysfs /sys sysfs rw 0 0
# Gentoo configurations
/dev/hdb3 /gentoo ext3 users,owner,noatime,rw 0 2
já i meme essa celui ci apres rien
/dev/hdb3 /gentoo ext3 users, rw,owner,noatime 0 2
/dev/hdb1 /gentoo/boot ext2 owner,noatime,rw 0 2
proc /gentoo/proc proc defaults 0 0
normal que cela ne marche pas (les messages d'erreurs sont plus
explicite qu'un "ca marche pas !').
la fstab de gentoo doit ressembler à :
# Gentoo configurations
/dev/hdb3 / ext3 users,owner,noatime,rw 0 2
/dev/hda2 none swap sw 0 0
já i meme essa celui ci apres rien
proc /proc proc defaults 0 0
/dev/fd0 /floppy auto user,noauto 0 0
/dev/hdc /cdrom iso9660 ro,user,noauto 0 0
sysfs /sys sysfs rw 0 0 # uniquement pour noyau 2.6.x
voila mon fichier /etc/lilo.conf apres configuration
#
lba32
# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81
#disk=/dev/sda
# bios=0x80
boot=/dev/hda
ta partition de boot n'ets pas hdb1 ? donc boot = /dev/hdb
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda1
ne pas le mettre ici ! mais dans chacune des image
#
# compact
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-bmp.b
bitmap=/usr/share/lilo/contrib/sid.bmp
bmp-colors=1,,0,2,,0
bmp-table=120p,173p,1,15,17
bmp-timer=254p,432p,1,0,0
# Specifies the location of the map file
#
map=/boot/map
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
# single-key
# delay=100
timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Boot up Linux by default.
#
default=Linux
image=/vmlinuz
label=Linux
read-only
ici root=/dev/hda1
# restricted
# alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
#
# gentoo
image=/gentoo/boot/kernel-2.4.25-gentoo
label=Gentoo
read-only
root=/dev/hdb3
l'autre root préciser au départ doit interferer avec celle ci
Comment par faire la modif de ton lilo.conf et relance lilo
# restricted
# alias=3
Quand je fait # lilo
tout est okay
Linux*
LinuxOld
Gentoo
....
Mais quand je coisis Gentoo ...le boot image n´est pas reconnu
Peace
J8.
Reply to: