kernel 2.4.9 et initrd ...
Bonjour,
Après quelques recherches infructeuses dans les archives des listes
Debien et dans la documentation du kernel, je dois me tourner vers vous.
Voilà mon petit problème :
Après téléchargement et installation d'un kernel-2.4.9-586 de Debian,
changement du lilo.conf pour prendre en compte le initrd (nouveau depuis
le 2.2.17 que j'avais avant ...) he ben au démarrage, après chargement
du ramdisk (normal apparemment) et prompt pour avoir le shell , il me
fait un "kernel panic : attempt to kill init" et bloque là !!!
Qu'est ce que j'ai fait (ou plutôt pas fait) de mal pour tant de haine ?
Heureusement j'avais encore l'ancien kernel en secours sinon ...
Le initrd fournit avec le kernel serait-il incomplet ? Faut-il y changer
quelquechose, ajouter un programme, une commande ?
Je joint mon lilo.conf au cas où ...
Merci d'avance
Didier
--
+---- \\\// --[Didier Link -> dLink@hfsp.org]-----------------+
| (0 -) |
+-oOO--(_)--OOo-------- -> Use Debian GNU/LinuX <- -----------+
-+
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda2
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
#
install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
#delay=0
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
message=/boot/bootmess.txt
prompt
# single-key
delay=100
timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
vga=ask
# vga=9
# vga=extended
# vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=Linux
image=/vmlinuz
label=Linux
read-only
initrd=/boot/initrd
append="root=/dev/rd/0 init=/linuxrc rw"
# restricted
# alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
Reply to: